|
|
|
Machinery Accessories - Band Saws
|
STEEL CITY™ 14" BAND SAW HAS 2 SPEEDS AND COMES WITH LOADS OF CONVENIENT FEATURES
|
| Riser Block Kit For 14" Band Saw
...plus other(s)
|
THE STEEL CITY™ 50100 14" DELUXE BAND SAW HAS THE FEATURES FOR VERY CONVENIENT OPERATION:
1-1/2HP, 115/230V, 1PH TEFC MOTOR W/MECHANICAL ON/OFF SWITCH - 1,500/3,000 SFPM. 13" BLADE TO FRAME 6-1/4" UNDER GUIDE (12" WITH OPTIONAL RISER BLOCK). 16" X 16" CAST IRON TABLE WITH MITER SLOT TILTS 48° RIGHT AND 10° LEFT. 93-1/2" STANDARD BLADE LENGTH, 1/8" TO 3/4" WIDTH. 7-1/2" MAXIMUM RIP RIGHT OF BLADE; 11-3/4" LEFT (USING OPTIONAL RIP FENCE). COMES WITH MOBILE BASE INTEGRATED INTO THE STAND, WHEEL BRUSH, WRENCHES AND INSTRUCTIONS. 68"H X 38"W X 27"D. 271 LBS. NET WEIGHT; 291 LBS. SHIPPING WEIGHT. FIVE YEAR MANUFACTURER'S WARRANTY. IMPORTED.
|
|
|
|
Machinery Accessories - Band Saws
|
COOL BLOCKS® FINE TUNE YOUR BAND SAW
|
| Cool Blocks 14" Delta
...plus other(s)
|
THE HEAT AND FRICTION CAUSED BY METAL GUIDE BLOCKS ARE ELIMINATED WITH PATENTED OLSON® COOL BLOCKS®, WHICH REPLACE YOUR STANDARD UPPER AND LOWER BLADE GUIDES, ALLOWING BLADES TO RUN COOLER, QUIETER AND LAST LONGER - FOUR-PIECE SETS REQUIRE NO BAND SAW MODIFICATION:
CB50000 - DELTA® 14"
|
|
|
|
Machinery Accessories - Band Saws
|
BRETT-GUARD® BAND SAW GUARD ADDS SAFETY AND VISIBILITY TO YOUR WORK
|
| Brett Band Saw Guard, Jet 14"
...plus other(s)
|
BUILT-IN 120V LIGHT NOT ONLY ILLUMINATES THE CUTTING LINE BUT ALSO BRIGHTENS THE WORK AREA WHEN YOU USE THE BRETT-GUARD® BAND SAW GUARD, FROM HTC PRODUCTS:
GUARD MOUNTS AT AN ANGLE TO PREVENT INTERFERENCE WITH SAW GUIDE COMPONENTS. A SINGLE KNOB ADJUSTS THE CLEAR, PLEXIGLAS SHIELD. ATTACHED TO THE BLADE SUPPORT ARM, IT MOVES AS YOU ADJUST DEPTH OF CUT. A-100-4 FITS JET® 14" BANDSAWS. A-100-14 FITS DELTA® 14" BANDSAWS. MOUNTING BRACKET, POWER CORD, HARDWARE AND INSTRUCTIONS INCLUDED. SHIPPING WEIGHT 6 LBS.
|
|
|
|
Machinery Accessories - Band Saws
|
ADJUST BANDSAW BLADE TENSION WITH THE FLIP OF A LEVER
|
| Carter Quick Release
|
USING THE CARTER QUICK RELEASE™ ON YOUR BANDSAW, IT'S EASY TO INSTANTLY RELIEVE TENSION TO PREVENT DAMAGE TO THE TIRE AND PROLONG THE LIFE OF THE BLADE AND SAW:
THREE POSITION LEVER CONTROL ALLOWS FULL RELEASE, PARTIAL TENSION OR FULL TENSION (FINE TUNE USING BANDSAW SCREW CONTROL). USE WITH BLADES FROM 1/8"W TO 3/4"W. INSTALLS IN JUST MINUTES; ALL HARDWARE PROVIDED ALONG WITH DETAILED, FULLY ILLUSTRATED MOUNTING INSTRUCTIONS. FITS JET, DELTA®, RIDGID® AND SEARS® CONTRACTOR 14" BANDSAWS. BUILT TO LAST WITH SOLID STEEL CONSTRUCTION AND HIGH QUALITY COMPONENTS. USA.
|
|
|
|
Machinery Accessories - Band Saws
|
CERAMIC GUIDE BLOCKS AND BEARINGS IMPROVE BAND SAW PERFORMANCE
|
| Ceramic Guide Blocks For Delta 14"
...plus other(s)
|
GET COOLER, QUIETER BANDSAW OPERATION WITH ALUMINA-OXIDE SPACEAGE CERAMIC GUIDEBLOCKS® AND THRUST BEARINGS. FOUR-PIECE GUIDE BLOCK SETS HANDLE UPPER AND LOWER GUIDES AND WORK WITH ANY BLADE WIDTH:
108-443 SET FITS DELTA® 14" BAND SAWS (THREE 1/2" X 1/2" X 3/4" BLOCKS; ONE 1/2" X 3/8" X 1"). 108-737 SET IS DESIGNED FOR JET®, GRIZZLY®, OTHER IMPORTED 14" PLUS GENERAL 15" BAND SAWS (FOUR 1/2" X 1/2" X 3/4" BLOCKS). 126-461 TWO-PIECE THRUST BEARING SET (1-3/16 DIA. W/WASHERS) REPLACES DELTA®, JET®, GRIZZLY® AND OTHER IMPORTED 14" BAND SAW UPPER AND LOWER BEARINGS. INSTALLATION INSTRUCTIONS INCLUDED. LIFETIME MANUFACTURER'S WARRANTY. USA.
|
|
|
|
Machinery Accessories - Band Saws
|
ADD A SAWMILL TO YOUR SHOP
|
| Large Hand Held Saw Mill
...plus other(s)
|
USING THE HAND HELD SAWMILL™ AND YOUR BAND SAW, YOU CAN SAFELY CUT BOARDS TO YOUR SPECIFICATIONS FROM SMALL LOGS OR ROUGH STOCK - MAKE LUMBER AT A FRACTION OF THE COST OF COMMERCIALLY MILLED LUMBER!
LARGE HAND HELD SAWMILL™ FITS FLOOR MOUNTED BAND SAWS; 6-1/2"H X 8"W X 15"L; ADJUSTABLE BAR FITS MOST MITER SLOTS. SMALL HAND HELD SAWMILL™ FITS TABLE TOP BANDSAWS; 4-1/2"H X 6"W X 8"L.
|
|
|
|
Machinery Accessories - Band Saws
|
BOLT-ON BAND SAW FENCE FEATURES T-SLOT DESIGN AND LOTS OF OPTIONS
|
| 18" Capacity Bandsaw Fence System
...plus other(s)
|
THE PATENTED 18" CAPACITY BOLT-ON BAND SAW FENCE IS DESIGNED TO ATTACH TO 14" DELTA® AND MOST IMPORTED BAND SAWS (SAE AND METRIC FASTENERS INCLUDED) TO PROVIDE GREATER ACCURACY AND ADDITIONAL OPTIONS:
MOUNTING BRACKET, RAIL AND FENCE ARE EXTRUDED ALUMINUM FOR DURABILITY. T-SLOTS ON TOP AND FACE OF RAIL AND FENCE ALLOW SIMPLE JIG AND FIXTURE ATTACHMENTS, USING 1/4"-20 CAP SCREWS. FENCE AND RAIL ARE EACH 19-1/4" LONG - RAIL SLIDES TO ONE SIDE TO ALLOW USE OF MITER SLOT.
BY ADDING THE 4-1/2" RESAW GUIDE TO THE BOLT-ON BAND SAW FENCE, STOCK CAN BE RESAWN TO UNIFORM THICKNESS BY ELIMINATING "DRIFT" THAT CAN MAKE BAND SAW CUTS DIFFICULT: RESAW GUIDE BOLTS SECURELY ONTO FENCE RAIL AND ITS CURVED FACE SUPPORTS WOOD, BUT ALLOWS FEED ANGLES TO BE ADJUSTED WHILE THE DISTANCE BETWEEN GUIDE AND BLADE REMAINS CONSTANT.
WHEN STOP POSITIONS NEED TO BE ADJUSTED BY THOUSANDTHS OF AN INCH, ADD THE PATENTED MICROADJUSTER TO YOUR BOLT-ON BAND SAW FENCE: CLAMPED ONTO THE RAIL BESIDE THE FENCE, MICROADJUSTER ALLOWS FOR VERY PRECISE (0.008") ADJUSTMENTS TO FENCE SETTINGS.
ALL HARDWARE AND INSTRUCTIONS INCLUDED WITH EACH ITEM.
|
|
|
|
Machinery Accessories - Band Saws
|
ULTRA BLUE™ URETHANE BANDSAW TIRES INSTALL FASTER, LAST LONGER
|
| 10" X 7/8" Urethane Bandsaw Tire
...plus other(s)
|
CARTER ULTRA BLUE™ URETHANE BANDSAW TIRES INSTALL WITHOUT ADHESIVE BONDING, MEANING YOUR SAW CAN BE RETURNED TO SERVICE UP TO 48 HOURS SOONER COMPARED TO USING NATURAL RUBBER TIRES:
URETHANE IS STRONGER, LONGER LASTING AND TRUER RUNNING THAN RUBBER - INSTALLATION INSTRUCTIONS INCLUDED. NOTE: MEASUREMENTS APPROXIMATE DUE TO MANUFACTURING DIFFERENCES. USA.
|
|
|
|
Machinery Accessories - Band Saws
|
PRECISION BLADE GUIDES AND CAST IRON TABLE KEEP THE WOODTEK® TWO SPEED 14" BANDSAW RUNNING SMOOTHER
|
| Zero Clearance Insert (white)
...plus other(s)
|
WITH TWO UPPER AND TWO LOWER SIDE BEARINGS THAT STAY IN ROLLING CONTACT WITH THE BLADE, THE WOODTEK® TWO SPEED 14" BANDSAW TRACKS STRAIGHT AND RUNS COOL - A THIRD BEARING SUPPORTS THE BACK OF THE BLADE FOR MORE CONSISTENT CUTS WITH LESS FEED PRESSURE (ESPECIALLY HELPFUL WHEN RESAWING):
HEAVY CAST IRON TABLE HAS 3/8" X 3/4" MITER SLOT AND OFFERS VIBRATION FREE PERFORMANCE. BLADE CHANGES ARE QUICK AND EASY WITH DOORS THAT SWING WIDE OPEN. AIR NOZZLE, SAWBLADE, URETHANE TIRES, MITER GAUGE, EXTRUDED ALUMINUM FENCE SYSTEM, WRENCHES AND INSTRUCTION MANUAL INCLUDED. ONE YEAR PARTS AND WORKMANSHIP WARRANTY. IMPORTED.
SPECIFICATIONS:
MOTOR - 1HP, 120V, 1PH, 10A, 1,750 RPM - "V" BELT DRIVE (8' POWER CORD AND PLUG INCLUDED). ON/OFF SWITCH - PUSH BUTTON, MECHANICAL. BLADE SPEED - 1,720 OR 2,900 FPM. BLADE SIZE - 93-1/2", 1/4" TO 3/4" WIDE (13-7/8" DIA. WHEELS). HEIGHT CAPACITY - 6". DEPTH CAPACITY - 13-1/2". TABLE SIZE - 16-1/16" X 16-1/2"; TILTS 13°L AND 50°R. DUST PORT - 2-1/4" DIA. OVERALL DIMENSIONS - 67"H X 29-1/2"W X 19-1/8"D. SHIPPING WEIGHT - 194 LBS.
WOODWORKER'S SUPPLY® STOCKS MORE THAN 5,000 WOODTEK® PARTS IN ITS WYOMING WAREHOUSE. EXPERIENCED TECHNICIANS READY TO ASSIST YOU - SAME DAY SHIPPING ON MOST ORDERS. CALL 1-800-545-9663, M-F, 7 AM-4 PM, MOUNTAIN TIME.
|
|
|
|
Machinery Accessories - Band Saws
|
POWERMATIC® PWBS-14CS CLOSED STAND 14" BAND SAW INCLUDES RIP FENCE WITH RESAW ASSEMBLY
|
| 6" Riser Block For Pwbs-14cs
...plus other(s)
|
"ONE SOLID MACHINE" AND "PURRED LIKE A KITTEN" ARE WORDS WOOD® MAGAZINE EDITORS USED TO DESCRIBE THE POWERMATIC® PWBS-14CS 14" BAND SAW:
1-1/2 HP, 115/230V, 1PH MOTOR - 3,000 SFPM. MICRO ADJUSTABLE, DUAL BEARING BLADE GUIDE SYSTEM ABOVE AND BELOW THE TABLE - 6" UNDER GUIDE CAPACITY; 13-1/2" FRAME TO BLADE CLEARANCE. TWO PIECE CAST IRON TABLE HAS 5" X 15" TILTING (45° RIGHT, 10° LEFT) SECTION AND FIXED 15" X 5" EXTENSION - CHIP BLOWER ENSURES CLEAN, VISIBLE CUT LINE. TENSIONING GAUGE SETTINGS INDICATED IN "BLADE WIDTH" INCREMENTS - CARTER QUICK RELEASE™ LEVER SPEEDS BLADE CHANGES. BALANCED, NINE SPOKE CAST IRON WHEELS RUN SMOOTHLY - POLY V-BELT MAXIMIZES POWER TRANSMISSION WHILE MINIMIZING NOISE AND VIBRATION. ONE PIECE WELDED STAND REQUIRES NO ASSEMBLY - BUILT IN 4" DUST PORT. MITER GAUGE, 1/4" X 93-1/2" BLADE, 60 WATT HALOGEN WORK LIGHT, TOOL KIT AND INSTRUCTIONS INCLUDED. 68"H X 34"W X 20"L. 203 LBS. NET WEIGHT; 221 LBS. SHIPPING WEIGHT. FIVE YEAR MANUFACTURER'S WARRANTY. IMPORTED.
|
|
|
|
Machinery Accessories - Band Saws
|
BAND SAW FENCE SYSTEM FEATURES T-SLOT DESIGN AND LOTS OF OPTIONS
|
| Kreg Precision Band Saw Fence
...plus other(s)
|
THE PATENTED KREG™ KMS7200 PRECISION BAND SAW FENCE COMBINES UNPARALLELED RIGIDITY AND PRECISION:
TWO DIMENSIONAL ADJUSTMENT SIMPLIFIES SETTING THE FENCE PARALLEL TO THE BLADE. CUTTING ACCURACY AND REPEATABILITY ENHANCED BY PRECISION LENS CURSOR AND INCLUDED SCALE. RIGID, INTERLOCKING DOVETAIL DESIGN - FITS MOST DELTA®, JET®, GENERAL®, GRIZZLY® AND OTHER 14" BAND SAWS. OPTIONAL KMS7215 MICRO-ADJUSTER CLAMPS ONTO RAIL BESIDE FENCE ALLOWING VERY PRECISE (0.008") ADJUSTMENTS. OPTIONAL KMS7213 4-1/2" AND KMS7214 7" RESAW GUIDES ELIMINATE "DRIFT" SO STOCK CAN BE CUT TO UNIFORM THICKNESS. GUIDES BOLT ONTO FENCE RAIL BUT ALLOW FEED ANGLES TO BE ADJUSTED WHILE GUIDE-TO-BLADE DISTANCE REMAINS CONSTANT. ONE YEAR MANUFACTURERS WARRANTY. USA.
|
|
|
|
Machinery Accessories - Band Saws
|
JET® 14" BAND SAWS
|
| Rip Fence For Jet 14" Band Saw
...plus other(s)
|
WITH ALL OF ITS FEATURES, THE JET® JWBS-14CS (708115K) 14" CLOSED STAND WOODWORKING BAND SAW WILL BE A WELCOME ADDITION TO YOUR SHOP:
1HP, 115/230V, 1PH TEFC MOTOR - 3,000 SFPM. MICRO ADJUSTABLE BLADE GUIDE WITH GRAPHITE IMPREGNATED JET BLOCKS™ FOR SMOOTHER RUNNING. 6" UNDER GUIDE CAPACITY; 13-1/2" FRAME TO BLADE CLEARANCE. 15" X 15" CAST IRON TABLE TILTS 45°R AND 10°L. ONE PIECE WELDED STAND REQUIRES NO ASSEMBLY - BUILT IN 4" DUST PORT. 3/8" X 93-1/2" 6TPI BLADE AND INSTRUCTIONS INCLUDED. SIMILAR JWBS-14MW (708116K) 14" CLOSED STAND METALWORKING BAND SAW FEATURES THREE SPEEDS (735, 1,470, 2,350 SFPM) FOR NON-FERROUS METAL AND WOODWORKING APPLICATIONS. 68"H X 26"W X 19"D. 185 LBS. NET WEIGHT; 200 LBS. SHIPPING WEIGHT. JWBS-14OS (708113A) 14" OPEN STAND WOODWORKING BAND SAW FEATURES: 3/4HP, 115/230V, 1PH TEFC MOTOR - 3,000 SFPM. 6" UNDER GUIDE CAPACITY; 13-1/2" FRAME TO BLADE CLEARANCE. 14" X 14" CAST IRON TABLE TILTS 45°R AND 15°L. 16GA STEEL STAND - BUILT IN 4" DUST PORT. 3/8" X 93-1/2" 6TPI BLADE AND INSTRUCTIONS INCLUDED. 68"H X 24"W X 26-1/2"D. 172 LBS. NET WEIGHT; 187 LBS. SHIPPING WEIGHT.
5 YEAR MANUFACTURER'S WARRANTY. IMPORTED.
|
|
|
|
Machinery Accessories - Band Saws
|
REPLACEMENT SPRING ALLOWS YOU TO BOOST BANDSAW BLADE TENSION 200% TO 300%
|
| Cobra Coil
|
AFTER INSTALLING THE CARTER COBRA COIL™ BANDSAW TENSION SPRING REPLACEMENT IN YOUR 14" BANDSAW, YOU SHOULD BE ABLE TO CUT FASTER, MORE ACCURATELY, REDUCE MAINTENANCE AND REPLACE YOUR BLADES LESS FREQUENTLY:
3/4" OD X 2-9/16" SPRING ALSO ALLOWS USE OF LARGER BLADES THAT REQUIRE TENSION NOT AVAILABLE WITH STOCK SPRINGS. MANUFACTURED TO ASTM SPECIFICATIONS USING HEAT TREATED AND TEMPERED CHROMIUM VANADIUM STEEL. SIMPLE INSTALLATION (INSTRUCTIONS INCLUDED). FITS 14" JET®, DELTA®, GENERAL®, RIDGID®, RELIANT, GRIZZLY®, SEARS® CONTRACTOR AND MOST IMPORTED BANDSAWS. USA.
|
|
|
|
Machinery Accessories - Band Saws
|
CARTER CLEAN SWEEP™ BANDSAW WHEEL BRUSH
|
| Band Saw Lower Wheel Brush
|
A GREAT IDEA IF YOU ARE LOOKING AT AN UPGRADE, THE CARTER CLEAN SWEEP™ 14" BANDSAW WHEEL BRUSH EXTENDS TIRE LIFE, IMPROVES BLADE TRACKING AND - BEST OF ALL - IS EASY TO INSTALL:
BRUSH INSTALLS WITHIN REACH OF YOUR BANDSAW'S LOWER WHEEL (MOUNTING INSTRUCTIONS AND MOUNTING SCREW INCLUDED). USA.
|
|
|
|
Machinery Accessories - Band Saws
|
KEEP YOUR FINGERS FURTHER AWAY FROM THE BLADE WHEN CUTTING SMALL WORKPIECES ON A BAND SAW
|
| Joy-jaw Bandsaw Pushstick
|
JOY-JAW™ BAND SAW PUSH BLOCK CAN BE USED TO FEED SMALL WORK PIECES THROUGH WOOD CUTTING OR METAL CUTTING BAND SAWS. THE STEPPED JAWS HOLD THE WORK PIECE IN PLACE WHILE MOLDED GRIPS AND WIRE GUARDS SHIELD FINGERS.
DESIGNED TO BE USED IN MULTIPLE POSITIONS MAKING IT THE IDEAL TOOL TO MEET YOUR SPECIFIC PROJECT REQUIREMENTS. MOLDED CO-POLYMER PLASTIC IS TOUGH AND RIGID YET WONT DAMAGE SAW BLADE. STURDY HANDLES PROVIDE COMFORTABLE CONTROL. DESIGNED AND MADE IN USA.
|
|
|
|
Machinery Accessories - Band Saws
|
RATCHET-ROD™/ MAKES BAND SAW BLADE TENSION ADJUSTMENT EASY
|
| Ratchet-rod Band Saw Blade Tension
|
CARTER® RATCHET-ROD™/ BAND SAW BLADE TENSION ROD KIT ADDS CONVENIENCE TO YOUR 14" BAND SAW.
QUICKLY TIGHTEN OR LOOSEN BLADE TENSION WITH PALM STYLE RATCHET. ACME THREADS HAVE SUPERIOR STABILITY AND REDUCED FRICTION FOR EASY OPERATION. KIT INCLUDES BLACK OXIDE COATED ROD & NUT AND CHROME PLATED PALM RATCHET. FITS 14" BAND SAWS, MOST BRANDS. ONE YEAR MANUFACTURER'S WARRANTY. USA.
|
|
|
|
Machinery Accessories - Band Saws
|
CARTER ROLLER GUIDES FOR DELTA® 14" BAND SAWS
|
| 28-198 Carter Roller Guides
|
CARTER ROLLER GUIDES REPLACE YOUR EXISTING GUIDES TO PROVIDE EXCELLENT CONTROL FOR BOTH GENERAL BAND SAW WORK AND RESAWING:
SIDE ROLLERS HOLD THE BLADE IN PLACE AND THE REAR THRUST BEARING IS ENGAGED BY CUTTING PRESSURE TO PROVIDE UNEQUALLED BLADE SUPPORT. TWO YEAR MANUFACTURER'S WARRANTY. IMPORTED.
|
|
|
|
Machinery Accessories - Band Saws
|
DELTA® BAND SAW BLADE GUIDES
|
| 14" Band Saw Blade Guides
...plus other(s)
|
DELTA® BLADE GUIDES HELP KEEP THE COMPANY'S 9" AND 14" BAND SAWS RUNNING SMOOTHER AND COOLER:
UPPER AND LOWER PHENOLIC GUIDES WILL NOT DAMAGE BLADE TEETH THROUGH ACCIDENTAL CONTACT. TWO YEAR MANUFACTURER'S WARRANTY. IMPORTED.
|
|
|
|
Machinery Accessories - Band Saws
|
ADD RIP FENCE ACCURACY TO YOUR DELTA® 14" BANDSAW
|
| Band Saw Rip Fence, 24" Rails
...plus other(s)
|
A GENUINE DELTA® MODEL 28-858 24" RIP FENCE MOUNTS DIRECTLY ONTO THE TABLE AND CAN BE THE MOST VALUABLE ACCESSORY YOU CAN ADD TO YOUR DELTA® 14" BANDSAW:
USE THE FENCE AND SAW TO PREPARE STOCK FOR TURNING, SPLIT DOWELS, RIP BEVELS, RIP EXTRA THICK STOCK, RESAW ACCURATELY AND MUCH MORE. INCLUDES STURDY ALUMINUM BODY, REMOVABLE PIVOT BAR FOR FREEHAND RESAWING, GUIDE RAILS AND MOUNTING HARDWARE. WEIGHS 15 LBS. 28-856 - HAVING SIMILAR FEATURES, THIS SMALLER DELTA® RIP FENCE (NOT SHOWN) IS 12" LONG BUT ALSO FITS 14" BANDSAWS. WEIGHS 12 LBS. TWO YEAR MANUFACTURER'S WARRANTY. IMPORTED.
|
|
|
|
Machinery Accessories - Band Saws
|
DOUBLE THE HEIGHT CAPACITY OF YOUR DELTA® 14" BANDSAW WITH A FACTORY BUILT ATTACHMENT
|
| Height Attachment/14" Bs
|
WHEN YOU ADD THE MODEL 28-984 HEIGHT ATTACHMENT TO YOUR DELTA® 14" BANDSAW, THE CAPACITY UNDER THE GUIDE INCREASES FROM 6-1/4" TO 12-1/4"!
GREAT FOR RESAWING, CUTTING ANGULAR PIECES LIKE CHAIR BACKS AND FOR CUTTING THICK CORBELS OR LOGS. INCLUDES CAST BLOCK, DOWELS AND BOLT, EXTENSION AND FRONT AND BACK BLADE GUARDS. WEIGHS 12 LBS. MUST BE USED WITH 105" BLADES.
|
|
|
|
Machinery Accessories - Band Saws
|
HITACHI® 14-1/2" BANDSAW FEATURES 3" WIDE BLADE FOR PRECISION RESAWING
|
| 1" Blade Guide For Cb75f
...plus other(s)
|
RESAWING VALUABLE WOOD IS FASTER AND MORE ACCURATE WITH THE LARGE BLADE CAPACITY OF THE HITACHI® CB 75F RESAW BANDSAW COMBINED WITH THE SAW'S 11-3/16" MAXIMUM CUTTING HEIGHT:
2.8HP, 120VAC, 15A, 1PH MOTOR - 900 RPM. HAND BRAKE NEXT TO START AND STOP BUTTONS FOR EXTRA SAFETY. 20-1/2" X 19-1/4" CAST IRON TABLE TILTS 45° AND HAS MITER GAUGE GROOVE. RACK AND PINION FENCE ADJUSTMENT PROVIDES SMOOTH OPERATION AND ACCURACY. ACCEPTS BLADES 1/4" TO 3" WIDE. ALL-STEEL BODY WITH BUILT-IN 4" DIA. DUST PORT. INCLUDES DURABLE 3" WIDE STELLITE® BLADE, GUIDE ASSEMBLY, TWO DOUBLE-END WRENCHES, BOX WRENCH, HEX BAR WRENCH, 6-1/2' LONG GROUNDED POWER CORD WITH PLUG AND INSTRUCTION MANUAL. 60"H X 37"W X 29"D, WEIGHS 308 LBS - DESIGNED FOR FLOOR MOUNTING. FIVE-YEAR MANUFACTURER'S WARRANTY. JAPAN.
HITACHI® CB 75F BANDSAW REPLACEMENT BLADES:
939-971 - 3" X 111.8" X 0.023" STELLITE® BLADE (12 TPF). 967-701 - 3" X 111.8" X 0.023" ALTERNATE-TOOTH STELLITE® BLADE (16 TPF). 921-705 - 1" X 110.75" X 0.025" SWAGED STEEL BLADE (24 TPF). 921-712 - 1/2" X 110.75" X 0.025" SWAGED STEEL BLADE (35 TPF). 921-719 - 1/4" X 110.75" X 0.025" SWAGED STEEL BLADE (48 TPF). 923-537 - 1" BLADE GUIDE (REQUIRED FOR 1" BLADE USE). 923-544 - 1/4" AND 1/2" BLADE GUIDE (REQUIRED FOR 1/4" AND 1/2" BLADE USE).
|
|
|
|
Machinery Accessories - Band Saws
|
EZ LOAD RADIUS CUTTER TAKES THE CHORE OUT OF CUTTING CIRCLES ON BANDSAWS; ALSO GREAT FOR RADIUS SANDING ON BELT/DISC MACHINES
|
| Ez Load Radius Cutter, 1"-48"
|
USING A BANDSAW AND THE EZ LOAD RADIUS CUTTER, YOU CAN CUT 1" TO 48" CIRCLES QUICKLY, EASILY AND ACCURATELY - EVERY TIME:
GLASS FILLED ABS BASE IS ATTACHED TO A MITER SLIDE ROD THAT LOCKS INTO BANDSAW TABLE MITER SLOT - TWO OPPOSING WEDGES LOCK THE SLIDER BASE INTO ANY 3/4" X 3/8" (OR DEEPER) MITER SLOT. DESIGN PROVIDES GREAT ACCURACY BY PREVENTING THE JIG FROM MOVING OR COMING OFF OF THE TABLE. 11-1/2" X 8" BASE OFFERS GREAT WEAR RESISTANCE, REDUCES FRICTION BETWEEN IT AND THE WORKPIECE AND PROVIDES A STABLE CUTTING PLATFORM. AN EXTRUDED ALUMINUM PIVOT BAR SLIDES AND LOCKS IN PLACE IN THE BASE - BAR HAS FOUR STRATEGICALLY LOCATED 1/4"-20 THREADED HOLES FOR LOCATING THE CENTERING PIN. EZ LOAD WILL NOT FIT SHOPSMITH MACHINERY. WEIGHS 3-1/2 LBS. USA.
|
|
|
|
Machinery Accessories - Band Saws
|
IMPROVE THE ACCURACY OF YOUR 14" BANDSAW
|
| Roller Guides, Jet 14" All Models
...plus other(s)
|
USING COMPACT, RUGGED, LUBRICATED FOR LIFE BALL BEARING GUIDES AT THE SIDES AND REAR OF THE BLADE, CARTER GUIDE SETS GIVE AN INCREDIBLE BOOST TO BANDSAW PERFORMANCE:
EASY TO INSTALL, ADJUST AND USE ON AN EVERYDAY BASIS. ECCENTRIC MOUNTS ALLOW FOR PRECISE POSITIONING FOR SUPERIOR CUTTING PERFORMANCE. DESIGN ALLOWS TABLE TO TILT FULL 45° FOR VERSATILITY AND HANDLES BLADES FROM 1/8" TO 1". INCLUDES UPPER AND LOWER GUIDE ASSEMBLIES, UPPER AND LOWER MOUNTING STUDS, UPPER AND LOWER MOUNTING ADAPTER BLOCKS AND NECESSARY MOUNTING HARDWARE. CHECK BANDSAW MOUNTING SHAFT - OLDER SAWS HAVE HEX SHAPED SHAFTS. USA.
|
|
|
|
Machinery Accessories - Band Saws
|
NATURAL RUBBER 70 DUROMETER BAND SAW TIRES
|
| 24" X 2" Rubber Bandsaw Tire
...plus other(s)
|
SOLD INDIVIDUALLY, 3/16" THICK NATURAL RUBBER BAND SAW TIRES ARE CONTINUOUS (ONE PIECE), WITH NO SPLICES THAT CAN CAUSE BUMPS OR BALANCE PROBLEMS:
EACH TIRE IS ABOUT 20% UNDERSIZED FOR PROPER TENSION AFTER STRETCHING AND IS OF STANDARD WIDTH. ONCE APPLIED USING ANY GOOD GRADE OF GLUE OR RUBBER CEMENT, EXCESS WIDTH CAN BE TRIMMED USING A SHARP KNIFE OR RAZOR BLADE. OIL, WEATHER, SUNLIGHT, OZONE AND ABRASION RESISTANT. BAND SAW SHOULD STAND 24 TO 48 HOURS BEFORE USE TO MAKE CERTAIN CEMENT IS DRY AND WELL SET. USA. NOTE: MEASUREMENTS CAN VARY DUE TO MANUFACTURING PROCESS.
|
|
|
|
Machinery Accessories - Band Saws
|
ZERO CLEARANCE TABLE INSERTS FOR DELTA® AND JET® BAND SAWS
|
| Zero Clearance Insert (yellow)
...plus other(s)
|
MADE OF 30% GLASS FILLED ABS PLASTIC FOR EXTREME DURABILITY AND RESILIENCY, ZERO CLEARANCE TABLE INSERTS HELP PROTECT BAND SAW BLADES IN CASE OF ACCIDENTAL CONTACT:
SPECIFICALLY DESIGNED TO FIT DELTA® AND JET 14" BAND SAWS. 2.49" DIA. X 3/32" THICK; KEEP SEVERAL ON HAND FOR USE WITH VARIOUS BLADES. A LOCATOR LINE MAKES IT EASY TO MAKE THE INITIAL CUT TO FIT THE DESIRED BLADE FOR PERFECT ZERO CLEARANCE CUTTING. SOLD IN PACKAGES OF FOUR - DELTA® INSERTS ARE YELLOW; JET® ARE WHITE.
|
|
|
|
Machinery Accessories - Band Saws
|
GET MORE PRECISION AND LONGER BAND SAW BLADE LIFE WITH AFFORDABLE BALL BEARING GUIDES
|
| Roller Guide Blocks, Delta 14"
...plus other(s)
|
BY REPLACING FACTORY BAND SAW BLADE GUIDES WITH THESE BALL BEARING GUIDES, YOU CAN IMPROVE PERFORMANCE AND INCREASE BLADE LIFE:
USE WITH 1/4" AND WIDER BLADES - VERY EASY TO INSTALL AND ADJUST. INCLUDES FOUR ALUMINUM BAR STOCK GUIDES, EACH WITH TWO DOUBLE SEALED, MICRO-PRECISION BALL BEARINGS. YOU'LL IMMEDIATELY NOTICE THAT THE BLADE CUTS STRAIGHTER AND WANDERS LESS, WHILE RUNNING COOLER. ON DELTA® BAND SAWS YOU CAN STILL TAKE ADVANTAGE OF THE FINE ADJUSTMENT SCREWS. USA.
|
|
|
|
Machinery Accessories - Band Saws
|
REPLACE YOUR BANDSAW SIDE SUPPORT BLOCKS TO GET UNMATCHED BLADE STABILITY
|
| Stabilizer For Shopsmith Bandsaws
...plus other(s)
|
CUTTING WITH 1/4" OR NARROWER BANDSAW BLADES CAN BE FRUSTRATING DUE TO A WANDERING BLADE. HOWEVER, WITH THE CARTER STABILIZER® YOUR SAW CAN HAVE UNMATCHED ACCURACY:
A SPECIAL GROOVED SUPPORT BEARING GIVES FULL SUPPORT TO THE BLADE'S REAR EDGE, PREVENTING IT FROM MOVING BACKWARDS OR SIDEWAYS. THE FRONT EDGE OF THE BLADE IS FREE TO FLEX INTO THE CUT, ALLOWING THE BLADE TO TRACK THROUGH THE TIGHTEST ALLOWABLE TURNS WITHOUT OVERSTRESSING. EASY TO INSTALL; SIMPLY REPLACE YOUR EXISTING UPPER GUIDE SUPPORT BLOCK ASSEMBLY AND THE STABILIZER® WILL PROVIDE RUGGED SUPPORT WITHOUT BINDING, ALLOWING THE BLADE TO RUN COOLER AND FRICTION FREE.
STD1 - FITS MOST 14" BANDSAWS INCLUDING DELTA®, JET, RIGID, SEARS® CONTRACTOR AND GRIZZLY®. SHS1 - FITS ALL SHOPSMITH MODEL BANDSAWS. SEA1 - FITS SEARS® 12", 1990 TO 1998 BANDSAWS WITH TWO PRONG GUIDE MOUNTING CONFIGURATION. SEA2 - FITS SEARS® 12" PRE-1990 BANDSAWS WITH HEX SHAPED UPPER GUIDE POSTS. SEA3 - FITS OLDER SEARS® MODELS WITH VERTICAL GUIDE ATTACHMENT BOLT.
|
|
|
|
Machinery Accessories - Boring
|
TWIN OVERLAY DOORS ARE SIMPLE WITH BLUM® HINGES
|
| Insertion Ram 107-120+ Hinges
...plus other(s)
|
THESE BLUM® BACK TO BACK OVERLAY DOOR HINGES ARE AVAILABLE IN SCREW-ON, PRESS-IN OR INSERTA™ TOOL-FREE MOUNTING STYLES:
MOUNT DOORS BACK TO BACK ON A SINGLE PANEL WITH THESE HINGE AND PLATE COMBINATIONS. THREE OPENING ANGLES (107°, 120°+, 170°). CHOOSE EXPANDO™ PLATE TO MOUNT TWIN DOORS INTO LINE BORED PANELS. A TRIAL MOCKUP IS SUGGESTED FOR ALL APPLICATIONS. LIFETIME MANUFACTURER'S WARRANTY. AUSTRIA.
|
|
|
|
Machinery Accessories - Boring
|
THESE BLUM® CLIP TOP™ HINGES GIVE INTERIOR DRAWERS FULL CLEARANCE
|
| Insertion Ram For Zero Protr. Hing
...plus other(s)
|
ALL METAL WITH NICKEL PLATING, THESE BLUM® CLIP TOP™ HINGES ARE FOR FRAMELESS OR FRAME APPLICATIONS IN CABINETS WITH INTERIOR DRAWERS OR PULLOUTS:
THREE DIMENSIONAL ADJUSTMENT FOR HORIZONTAL, VERTICAL AND IN/OUT ALIGNMENT, INCLUDING SPIRAL-TECH™ DEPTH ADJUSTMENT. DOORS COMPLETELY CLEAR THE CABINET OPENING STARTING AT 90° ALLOWING PULLOUTS TO PASS. MINIMUM -2.3MM PROTRUSION AT 90° WHEN USED WITH ZERO-HEIGHT MOUNTING PLATE. AVAILABLE IN SCREW-ON, PRESS-IN OR TOOL-FREE INSERTA™ MOUNTING. FOR MAXIMUM STRENGTH IN FACE FRAME APPLICATIONS, USE WRAPAROUND MOUNTING PLATE 175L6600.24. A TRIAL MOCKUP IS SUGGESTED FOR ALL APPLICATIONS. LIFETIME MANUFACTURER'S WARRANTY. AUSTRIA.
|
|
|
|
Machinery Accessories - Boring
|
BORE CABINET PARTS AND INSERT ALL TYPES OF BLUM® HARDWARE
|
| 7-spindle Boring Head F/minipress
...plus other(s)
|
THE BLUM® MINIPRESS P IS AN EASY TO USE MACHINE, DESIGNED FOR BORING ALL HINGE AND MOUNTING PLATE SYSTEMS, METABOX™ FRONT FIXING BRACKETS AND 32MM LINE BORING FOR CABINET SIDES USING AN OPTIONAL SEVEN SPINDLE LINE BORING HEAD:
220V, 1PH MOTOR - 220V, 3PH AVAILABLE AS A SPECIAL ORDER. SPINDLE CONFIGURATION IS ADJUSTED BY A 90° ROTATION OF THE HEAD. ONE SETTING IS DEDICATED TO THE BLUM® HINGE BORING PATTERN. PRESET DEPTH POSITIONS AND ADJUSTABLE FENCE STOPS MAKE SETUPS SIMPLE. THE MACHINE FEATURES A FIVE SPINDLE SWIVELING HEAD, PNEUMATIC MOISTURE TRAP, ADJUSTABLE STROKE AND BORING DEPTH, PNEUMATIC HOLD DOWN CLAMPS, SWING ARM FOR INSERTION RAM, DUST EVACUATION JET AND DUST COLLECTION ADAPTER. WORK TABLE, CENTER RULER, FOUR RULER STOPS, TWO FIXED BORING DEPTH STOPS, REPLACEMENT BREAKAWAY CLUTCH AND TOOL KIT INCLUDED. OPTIONAL INSERTION RAMS ARE AVAILABLE FOR MOST COMPONENTS. MANUFACTURER'S LIFETIME WARRANTY. AUSTRIA.
|
|
|
|
Machinery Accessories - Boring
|
KREG™ SEMI-AUTOMATIC POCKET HOLE MACHINE...WHEN IT'S TIME TO MOVE UP
|
| Dkdb 3/8" Step Drill Bit
...plus other(s)
|
IF YOUR PRODUCTION NEEDS HAVE OUTPACED MANUAL JIGS, IT MIGHT BE TIME TO CONSIDER THE ADDED SPEED AND CONVENIENCE OF THE KREG™ SEMI-AUTOMATIC FOREMAN:
DB55 PNEUMATIC FEATURES A 3/4HP PNEUMATIC MOTOR, AUTOMATIC AIR CLAMPING - 90-120 RECOMMENDED PSI; 5.3 CFM @ 90 PSI MINIMUM COMPRESSOR CAPACITY. DB110 ELECTRIC IS ENTIRELY ELECTRIC NO COMPRESSED AIR REQUIRED. LEVER OPERATED - ONE-SECOND CYCLE TIME. 3/8" DIA. STEP BIT PRODUCES FLAT BOTTOM, ROUND SIDED POCKET HOLES SO SCREW HEADS SEAT FLUSH AND HOLES CAN BE PLUGGED. 1/2" TO 1-1/2" MATERIAL CAPACITY. STABLE WORK SURFACE HAS EASILY ADJUSTABLE "SWING-STOP" MATERIAL POSITIONING GUIDES. HINGED TOP ALLOWS EASY ACCESS TO DRILL BIT AND MOTOR. 6-3/4"H (19" INCLUDING HANDLE) X 13-5/8"W X 22-5/8"D. 35 LBS. NET WEIGHT; 40 LBS. SHIPPING WEIGHT. ONE YEAR MANUFACTURER'S WARRANTY. USA
|
|
|
|
Machinery Accessories - Boring
|
DELTA® 32-350 HORIZONTAL BORING MACHINE
|
| 1/4" 10mm X 27mm Ct Boring Bit
...plus other(s)
|
MANUFACTURED FOR CABINET AND FURNITURE SHOPS, THE DELTA® MODEL 32-350 HORIZONTAL BORING MACHINE PERFORMS REPETITIVE OPERATIONS, QUICKLY AND EASILY:
1HP, 115/230V (WIRED 230V), 1PH, 3,450 RPM MOTOR - REQUIRES 90 PSI FOR OPERATION. 8-1/2" MAXIMUM MATERIAL THICKNESS. 3-7/8" HEAD TRAVEL; 3-1/2" TABLE TRAVEL TO CENTER OF BIT. SPINDLE ACCEPTS 7/16"-14 RH TPI. HEAVY 15-3/4" X 9-7/8" CAST IRON TABLE HAS DOVETAILED WAYS WITH AN ADJUSTABLE GIB. MITER GAUGE, ADJUSTABLE HOLD DOWN CLAMP WITH SEE-THROUGH GUARD, ADJUSTABLE STOCK STOP, ADJUSTABLE BORING HEAD, DRILL BIT ADAPTER, FOOT PEDAL, STEEL CABINET, DUST CHUTE, WRENCHES AND INSTRUCTION MANUAL INCLUDED. 48"H X 15-3/4"W X 37-1/2"L. 303 LBS. NET WEIGHT; 350 LBS. SHIPPING WEIGHT. TWO YEAR MANUFACTURER'S WARRANTY. IMPORTED
|
|
|
|
Machinery Accessories - Boring
|
QUICKLY COMPLETE CABINET ASSEMBLY WITH THE WOODTEK USA™ FACE FRAME ASSEMBLY SYSTEM
|
| 4'x8' Assembly Table
|
THE WOODTEK USA™ FACE FRAME ASSEMBLY SYSTEM HANDLES MATERIALS FROM 1/2" TO 1-1/2" THICK AND IS THE PERFECT CHOICE FOR FAST AND EFFICIENT CABINET ASSEMBLY:
4' X 8' FACE FRAME CLAMPING TABLE INCLUDES CLAMPING BEAM AND 4 INDIVIDUALLY CONTROLLED CLAMPING CYLINDERS (100-125 PSI REQUIRED). STRONG, ALL STEEL CONSTRUCTION. SHIPPED UNASSEMBLED (USER MUST SUPPLY DECK MATERIAL). WEIGHS 400 LBS. USA. NOTE: SHIPPED DIRECTLY FROM FACTORY - PLEASE ALLOW 4-6 WEEKS FOR DELIVERY.
|
|
|
|
Machinery Accessories - Drill Presses
|
FULL 6" STROKE MAKES THE STEEL CITY™ 17" DRILL PRESS STAND OUT
|
| Mortise Attachment For 17" Drill P
...plus other(s)
|
WITH ITS SPLIT HEAD CASTING DESIGN, THE STEEL CITY™ 20520 17" DRILL PRESS GIVES YOU THE ABILITY TO COMPENSATE FOR WEAR AND ENSURE QUILL ACCURACY OVER THE LIFE OF THE MACHINE:
3/4HP, 115/230VAC, 10/5A, 1PH, 1,725 RPM MOTOR - 16 SPEEDS (215-2,720 RPM); 5/8" CHUCK W/QUILL LOCK. RACK AND PINION RAISING/LOWERING MECHANISM. 3-1/8" COLUMN DIA.; #2 MT; 24" CHUCK TO TABLE; 43-3/4" CHUCK TO BASE. EXTERNAL MICRO-ADJUSTABLE DEPTH STOP IS EASILY ACCESSIBLE FOR FASTER, MORE ACCURATE DEPTH ADJUSTMENTS FOR REPETITIVE DRILLING. 12" X 12" CAST IRON TABLE TILTS 90°, LEFT AND RIGHT. INCLUDES STEP PULLEYS, POLY V-BELTS, CHUCK KEY, DRIFT KEY, LAMP ATTACHMENT (BULB NOT INCLUDED) AND INSTRUCTION MANUAL. 69"H X 14"W X 27"D. NET WEIGHT 227 LBS.; 251 LBS. SHIPPING WEIGHT. FIVE YEAR MANUFACTURER'S WARRANTY. IMPORTED.
|
|
|
|
Machinery Accessories - Drill Presses
|
LASER CROSSHAIR ATTACHMENT ADDS CONVENIENCE AND ACCURACY TO ANY DRILL PRESS
|
| Laser Attachment 120v Ac
|
THE STEEL CITY™ DUAL LASER ATTACHMENT ADDS PINPOINT ACCURACY TO YOUR DRILL PRESS - "X" MARKS THE SPOT, LITERALLY:
ALIGN THE RED INTERSECTING LASER LINES TO YOUR PENCIL MARK AND DRILL THE HOLE EXACTLY WHERE YOU WANT IT. OPERATES ON 120VAC OR 2 AA BATTERIES (NOT INCLUDED). 5 YEAR MANUFACTURERS WARRANTY. IMPORTED.
|
|
|
|
Machinery Accessories - Drill Presses
|
UTILI-TRAK DRILL PRESS TABLE GIVES YOU WHAT YOU REALLY NEED - MORE ROOM!
|
| 24" Drill Press Table
|
THE SMALL SIZE OF MANY DRILL PRESS TABLES REFLECTS THE TOOL'S HISTORY AS A METAL WORKING MACHINE. THE HART DESIGN™ MODEL DPT24 UTILI-TRAK DRILL PRESS TABLE & FENCE NOT ONLY ADDS THE ROOM AND STABILITY MOST WOODWORKERS WANT AND NEED, IT ALSO PROVIDES ALMOST UNLIMITED OPTIONS IN CLAMPING AND POSITIONING STOCK FOR DRILLING AND BORING:
17" X 24" TABLE CAN BE USED WITH 10" OR 12" DRILL PRESSES. 24" SOLID ALUMINUM FENCE ADJUSTS TO A PERFECT 90° TO TABLE SURFACE. QUICK ACTION CAM LEVERS. 1-1/16" THICK SOLID MDF TABLE - HIGH PRESSURE LAMINATE TOP AND BOTTOM SURFACES. T-SLOTS THAT ACCEPT CLAMPS, STOPS, JIGS AND FIXTURES. REPLACEABLE TABLE INSERT TO BACK UP STOCK WHEN DRILLING. ALSO COMES WITH TWO 12" UTILI-TRAKS, TWO 17" UTILI-TAPE TRACKS, TWO T-TRACK HOLD DOWNS, ONE MINI-STOP, THREE 36" SELF ADHESIVE TAPES FOR FENCE AND UTILI-TAPE TRACKS PLUS COMPLETE INSTRUCTIONS. 15 LBS. SHIPPING WEIGHT. USA.
|
|
|
|
Machinery Accessories - Drill Presses
|
VERMONT AMERICAN® 1/4" KEYLESS DRILL CHUCK FITS CORDLESS AND PORTABLE ELECTRIC DRILLS
|
| 3/8" Keyless Chuck
|
VERMONT AMERICAN® MODEL 14935 KEYLESS DRILL CHUCK USES HEAVY DUTY, SERRATED STEEL JAWS TO PROVIDE MORE GRIPPING POWER:
1/4" CHUCK WITH 3/8"-24 THREAD SPINDLE. RUBBERIZED COLLAR FOR EASIER TIGHTENING - STEEL NOSE TO WITHSTAND DAMAGE. USA.
LIMITED TO QUANTITIES ON HAND
|
|
|
|
Machinery Accessories - Drill Presses
|
TURN YOUR DRILL PRESS INTO A MORTISING MACHINE WITH A DELTA® MORTISING ATTACHMENT KIT
|
| 17-924 Mortising Kit
|
THE VERSATILE DELTA® MODEL 17-924 MORTISING ATTACHMENT KIT COMES WITH FOUR POPULAR MORTISING CHISEL AND BIT SETS PLUS A HANDY CARRYING CASE THAT HOLDS EVERYTHING FOR EASY STORAGE:
ATTACHES TO DRILL PRESS IN MINUTES WITHOUT THE NEED FOR INSTALLATION TOOLS. LARGE 4" CAPACITY UNDER HOLD DOWN - 2-3/4" CAPACITY FROM ENDS OF CLAMP RODS TO FENCE. COMES WITH 1/4" X 1/4", 5/16" X 5/16", 3/8" X 3/8" AND 1/2" X 1/2" HOLLOW CHISELS AND DRILL BITS, SPECIAL ALIGNMENT GAUGE FOR FAST, ACCURATE SET UPS, LARGE, CAST IRON FENCE ASSEMBLY, BUSHINGS, GUIDES, HEX WRENCH AND INSTRUCTIONS. FITS DRILL PRESSES WITH 38MM, 48MM, 50.8MM AND 66MM QUILL DIAMETERS, INCLUDING DELTA® MODELS 11-090, 11-980, 11-990, 14-040, 14-070, 17-900, 17-925 AND 17-965, PLUS SEARS® MODELS 21313, 21315 AND 21317. KIT WEIGHS 16 LBS. TWO YEAR MANUFACTURER'S WARRANTY. IMPORTED.
|
|
|
|
Machinery Accessories - Drill Presses
|
DRILL/MILL LASER GUIDE ENSURES PRECISE ALIGNMENTS
|
| Av21400 Drill/mill Laser
|
THE DRILL/MILL LASER AV21400 PROJECTS A BEAM OF BRIGHT RED LASER LIGHT DIRECTLY AT THE CENTER POINT OF YOUR DRILL, LATHE OR SPINDLE TOOL SO YOU CAN PRECISELY MARK DRILLING POSITIONS OR EXTEND CENTER LINES FOR ALIGNMENT. THE STUD ON THE REAR OF THE TOOL FITS INTO ANY 1/4" OR LARGER CHUCK.
THE HORIZONTAL AND VERTICAL POSITION OF THE BEAM CAN BE ADJUSTED WITH THE THREE ADJUSTMENT SCREWS. MAXIMUM RANGE IS 20 FT. IDEAL FOR CHECKING ANGLES. IF YOU HAVE A RADIAL DRILL PRESS OR VERTICAL MILLING MACHINE AND YOU WANT TO MAKE SURE YOUR HEAD IS TILTED TO 45 DEGREES, THE LASER BEAM WILL ALLOW YOU TO LINE IT UP PERFECTLY AGAINST A SQUARE OR PROTRACTOR. SUITABLE FOR ALL HAND-HELD DRILLS, STATIONERY DRILL PRESSES AND VERTICAL MILLING MACHINES. IN A DRILL PRESS, IT CAN ALSO BE USED TO DETERMINE IF THE SPINDLE OR ARBOR IS BENT. EXCELLENT AS A LINE-UP TOOL FOR YOUR WOOD OR METAL LATHE, THE LASER LETS YOU INSTANTLY CHECK YOUR TAIL STOCK ALIGNMENT. SIMPLE TO USE, THE STUD ON THE REAR OF THE TOOL FITS INTO ANY 1/4" OR LARGER CHUCK.
|
|
|
|
Machinery Accessories - Drill Presses
|
LUTHIERS FRIEND™ PRECISION THICKNESS SANDER
|
| Luthier's Friend Sanding Station
...plus other(s)
|
|
THE LUTHIER'S FRIENDTM IS A ONE STOP SANDING STATION DESIGNED TO MEET THE DEMANDS OF PRECISION WOODWORKING. WITH THE LUTHIER'S FRIEND, YOU CAN THICKNESS SAND WOOD PRECISELY DOWN TO 0.010"(0.25MM), MAKE DUPLICATE PARTS USING TEMPLATES, AND SHAPE COMPLEX PARTS FREEHAND. DUST FREE OPERATION IS ACHIEVED WITH EVEN THE SMALLEST SHOP VAC ATTACHED TO THE DUST SHROUD SURROUNDING THE DRUM. USE THE 2 X 3" ROBO-SANDERTM FLUSH TRIM SANDER TO DUPLICATE PARTS USING A TEMPLATE OR EVEN AN OLD PART AS A PATTERN. INCLUDES A 10" X 12" LAMINATED BASE, MICRO-ADJUSTABLE FENCE AND 2" X 3" ROBO-SANDERTM FLUSH TRIM SANDING DRUM FOR PATTERN AND THICKNESS SANDING OF WOOD UP TO 2-3/4" THICK. SETS UP EASILY ON A DRILL PRESS AND HANGS ON A NAIL WHEN NOT IN USE. MADE IN USA.
|
|
|
|
Advanced Search Tools
Browse our
to see Sub Categories)
