|
|
|
Clamps And Vises - Bar & Pipe Clamps
|
"JORGENSEN®" BAR CLAMPS - THE CHOICE OF CABINETMAKERS AND PROFESSIONAL WOODWORKERS
|
| 2" X 4" Light Duty Bar Clamp
...plus other(s)
|
"JORGENSEN®" BAR CLAMPS ARE BUILT EXTRA TOUGH AND COME IN SIZES TO MEET MOST CLAMPING REQUIREMENTS:
LIGHT DUTY - 3/16" X 5/8" STEEL BAR; 5/16" STEEL SCREW; 3/4" SWIVEL. 2" REACH - 300 LBS. LOAD LIMIT (CLAMP PADS INCLUDED). STANDARD DUTY - 1/4" X 3/4" STEEL BAR; 3/8" STEEL SCREW; 3/4" SWIVEL. 2-1/2" REACH - 600 LBS. LOAD LIMIT. HEAVY DUTY - 5/16" X 1" STEEL BAR; 1/2" STEEL SCREW; 1-3/16" SWIVEL. 3-1/2" REACH - 1,000 LBS. LOAD LIMIT (CLAMP PADS INCLUDED). DEEP REACH - 5/16" X 1-3/8" STEEL BAR; 5/8" STEEL SCREW; 1-1/4" SWIVEL. 5" REACH - 1,200 LBS. LOAD LIMIT.
MULTIPLE DISC CLUTCHES USE HARDENED, PLATED, HIGH CARBON STEEL WITH ROUNDED EDGES. MALLEABLE AND DUCTILE IRON CASTINGS; ORANGE BAKED ENAMEL FINISH. VARNISHED, SOLID MAPLE HANDLES. USA.
|
|
|
|
Clamps And Vises - Bar & Pipe Clamps
|
"JORGENSEN®" CABINET MASTER™ 90° PARALLEL JAW CLAMPS
|
| 3-3/4" X 12" Cabinet Master Clamp
...plus other(s)
|
REINFORCED STEEL AND CASTINGS ON THE "JORGENSEN®" CABINET MASTER™ 90° PARALLEL JAW CLAMP ARE PROTECTED WITH ORANGE PLASTIC:
MULTIPLE DISC CLUTCH USES HARDENED, PLATED, HIGH CARBON STEEL PLATES WITH ROUND EDGES. 1-3/16" X 3/8" BAR. SOLID MAPLE HANDLE FITTED TO 5/8" DIA., COLD DRAWN STEEL, ACME THREADED SCREW. 1,000 LB. LOAD LIMIT. USA AND IMPORTED.
|
|
|
|
Clamps And Vises - Bar & Pipe Clamps
|
"JORGENSEN®" DEEP REACH BAR CLAMPS
|
| 7" X 18" Steel Bar Clamp
...plus other(s)
|
USING A 3/8" X 1-1/2" STEEL BAR, THESE DEEP-REACHING "JORGENSEN®" BAR CLAMPS CAN HANDLE UP TO 1,200 LBS. OF LOAD:
7" DEEP CLAMPS HAVE A LARGE 1-1/4" SWIVEL THAT SITS AT THE END OF A 5/8" DIA., COLD DRAWN STEEL, ACME THREADED SCREW. SOLID MAPLE HANDLE. 9" DEEP CLAMPS FEATURE A 13/16" DIA. STEEL SCREW WITH ACME THREADS AND 1-3/8" DIA. SWIVEL. STEEL, SLIDING PIN HANDLE MALLEABLE AND DUCTILE IRON CASTINGS; ORANGE BAKED ENAMEL FINISH. IMPORTED.
TO HELP COMPLETE YOUR PROJECT, MAY WE SUGGEST:
BEAR PAW™ CLAMP PADS - 109-823.
|
|
|
|
Clamps And Vises - Bar & Pipe Clamps
|
EXTREMELY DEEP "JORGENSEN®" BAR CLAMP HAS 9" REACH
|
| 9" X 18" Deep Steel Bar Clamp
...plus other(s)
|
SUITABLE FOR BOAT BUILDING, OVERSIZED LAMINATING OR OTHER "BIG JOBS," THIS JORGENSEN® BAR CLAMP YIELDS A 1,200 LBS. LOAD LIMIT:
1-1/2" X 3/8" HIGH CARBON STEEL RUST RESISTANT BAR. 13/16" DIA. STEEL SCREW WITH ACME THREADS; STEEL, SLIDING PIN HANDLE; 1-3/8" DIA. SWIVEL. MALLEABLE AND DUCTILE IRON CASTINGS; ORANGE BAKED ENAMEL FINISH. USA.
|
|
|
|
Clamps And Vises - Bar & Pipe Clamps
|
QUICK-GRIP® ONE-HANDED BAR CLAMPS/SPREADERS SAVE YOU TIME AND EFFORT
|
| 6" Quick-grip Bar Clamp/spreader
...plus other(s)
|
IRWIN® QUICK-GRIP® ONE-HANDED BAR CLAMPS/SPREADERS FEATURE FAST, ONE-HANDED CLAMPING ACTION:
SQUEEZE THE PISTOL GRIP TO CLOSE; PULL THE TRIGGER TO RELEASE. HEAT-TREATED STEEL BAR RESISTS FLEXING UNDER LOAD. BODY IS HIGH-TECH LIGHTWEIGHT RESIN. SOFT JAW PADS PROTECT FINISHED OR DELICATE MATERIALS - REVERSE JAWS TO USE AS A SPREADER. MICRO AND MINI BAR CLAMPS CANNOT BE USED AS SPREADERS. IMPORTED.
|
|
|
|
Clamps And Vises - Bar & Pipe Clamps
|
WOODTEK 114608 JOINER CLAMPS WITH PADS - 2-1/2" X 6" AND LARGER
|
| 2-1/2" X 6" Joiner Clamp W/pads
...plus other(s)
|
MALLEABLE CAST IRON HEADS, CHROME PLATED STEEL GUIDE BARS AND MULTI-DISC CLUTCHES GIVE THESE CLAMPS HIGH PRICED FEATURES AT AN AFFORDABLE PRICE:
GUIDE BAR EXTENDS FULL LENGTH OF HEAD AND IS SECURELY FASTENED WITH A STEEL RIVET. SMOOTH HARDWOOD HANDLE IS FIRMLY PINNED TO FINE THREAD SCREW. CLAMP HEADS ARE FLAT ON THE BACK, ALLOWING THEM TO STAND UPRIGHT WHILE WORK IS ASSEMBLED. 2-1/2" TO 5" THROAT DEPTH. ALL SIZES INCLUDE NON-MARRING PADS TO PROTECT WORK PIECE. IMPORTED.
TO HELP COMPLETE YOUR PROJECT, MAY WE SUGGEST:
111-824 - BEAR PAW™ CLAMP PADS - CLICK HERE.
|
|
|
|
Clamps And Vises - Bar & Pipe Clamps
|
WOODTEK USA BEAR PAW CLAMP PADS FOR WOODWORKING CLAMPS
|
| Bear Paw Pipe Clamp Pads
...plus other(s)
|
IT'S BEEN SAID YOU CAN NEVER HAVE ENOUGH WOOD CLAMPS, BUT TO TAKE FULL ADVANTAGE OF ALL OF THOSE CLAMPS, YOU NEED WOODWORKER'S SUPPLY® BEAR PAW™ CLAMP PADS:
BEAR PAW™ FOR I-BEAM CLAMPS:
AVAILABLE FOR JOINER AND PIPE AND BAR CLAMPS, THESE VERSATILE PRODUCTS SUPPORT CLAMPS HORIZONTALLY OR VERTICALLY AND ALLOW FREE OPERATION OF CLAMP HANDLES.
BEAR PAW™ FOR PIPE AND BAR CLAMPS:
5-1/2" WIDE PADS STAY UPRIGHT AND STABLE IN THE VERTICAL OR HORIZONTAL POSITION, ALLOWING YOU TURN THE HANDLES WITHOUT INTERFERENCE. PADS DISTRIBUTE FORCE OVER THE ENTIRE FACE OF THE CLAMP ON LARGE SURFACES, OFFER AFFORDABLE K-BODY CLAMP FUNCTION AND ARE INTERCHANGEABLE TO FIT EITHER END OF THE CLAMP.
BEAR PAW™ FOR JOINER CLAMPS:
3-1/2" WIDE CLAMP PADS STAY UPRIGHT AND STABLE IN THE HORIZONTAL AND VERTICAL POSITION, ELIMINATING OLD STYLE SADDLES. SECURED WITH A LOCKING PIN SO THEY STAY IN PLACE, THESE PADS ARE DESIGNED TO PROTECT SURFACES BETTER THAN SMALLER SLIP-ON BUTTON STYLE PADS. SIMPLY SLIP ON OR OFF AS NEEDED - INTERCHANGEABLE TO FIT EITHER END OF THE CLAMP. PERFECT WHEN CLAMPING FACE FRAMES TO CABINETS AS WELL AS HUNDREDS OF OTHER CLAMPING NEEDS. FIT "JORGENSEN®" AND IMPORTED JOINER CLAMPS WITH 2-1/2" THROAT DEPTH AND 1/4" BAR.
AVAILABLE WITH OR WITHOUT NON-MARRING, GLUE-RESISTANT FACE PADS. U.S. PATENT 6,685,176 B2. USA.
|
|
|
|
Clamps And Vises - Bar & Pipe Clamps
|
THE BEST HEAVY DUTY CLAMPS WE HAVE EVER SEEN...AT AFFORDABLE PRICES
|
| Mod S 8.66"x11.81" Deep Reach
...plus other(s)
|
WHEN WOODWORKER'S SUPPLY® PRESIDENT AND FOUNDER JOHN WIRTH FIRST SAW THESE HEAVY DUTY CLAMPS, HIS REACTION WAS:
"WOW! THESE CLAMPS ARE INCREDIBLE - THEY WORK SMOOTHLY AND EASILY, YET WEIGH A TON AND GRIP LIKE A VISE. I ESPECIALLY LIKE THE SOLID STEEL PISTON, WHICH COMPLETELY ENCLOSES THE FAST-ACTING SCREW DRIVE, KEEPING IT FREE FROM GLUE, CHEMICALS AND OTHER CONTAMINANTS. I'M SURE YOU'LL AGREE THAT THESE FEATURES WILL BENEFIT YOU MANY YEARS DOWN THE ROAD WITH SMOOTH, RUGGED AND DEPENDABLE PERFORMANCE. ALL CLAMPS COME WITH A LIFETIME, FREE REPLACEMENT WARRANTY COVERING DEFECTS IN WORKMANSHIP AND MATERIAL. THAT'S GUARANTEED QUALITY AND VALUE FOR YOUR MONEY. TRY THEM FOR YOURSELF. I PROMISE YOU WON'T BE DISAPPOINTED."
PRODUCED BY PIHER®, A 46-YEAR-OLD COMPANY, THE CLAMPS WERE ORIGINALLY DESIGNED FOR THE WELDING AND CONSTRUCTION TRADES BUT HAVE BEEN ADAPTED TO WOODWORKING. NODULAR CAST IRON JAWS HAVE A BAKED ENAMEL FINISH WITH THE FIXED JAW DOUBLE-RIVETED TO THE MASSIVE, ABRASION RESISTANT STEEL BAR. KNURLED, NON-SLIP BRAKE ALLOWS MOVEABLE JAW TO SLIDE FREELY UNTIL PUT UNDER PRESSURE. 123-554 - OPTIONAL, ONE-SIZE-FITS-ALL CLAMP PADS (SOLD IN PAIRS) ARE EXTRA THICK, HEAVY DUTY NYLON. MODEL E BAR - 1.18" X 0.315", MODEL F BAR - 1.38" X 0.315", MODEL R, S, K BARS - 1.57" X 0.394". SPAIN.
|
|
|
|
Clamps And Vises - Bar & Pipe Clamps
|
WOODTEK 3/4" PIPE CLAMP
|
| 3/4" Pipe Clamp Set
...plus other(s)
|
EITHER OF THESE STURDY STEEL WOODTEK® PIPE CLAMP FIXTURES WILL ATTACH TO 3/4" DIA. THREADED BLACK PIPE (PIPE NOT INCLUDED) OF ANY LENGTH TO CREATE A POWERFUL CLAMP:
TAIL STOPS FEATURE MULTIPLE DISC CLUTCHES THAT GRIP THE PIPE AT ANY POINT BUT RELEASE, EASILY. 5/8" DIA. STEEL SCREWS - CRANK HANDLES PROVIDE EASY CONTROL.
123-758 - APPROXIMATELY 9"L X 4-1/2"H WITH 1-5/8" SQUARE CLAMP FACE (CLAMP PADS NOT INCLUDED), WEIGHS 2-1/4 LBS. 123-770 - APPROXIMATELY 14"L X 9-1/2H WITH 2" SQUARE CLAMP FACE (CLAMP PADS INCLUDED), WEIGHS 7-5/8 LBS. IMPORTED.
|
|
|
|
Clamps And Vises - Bar & Pipe Clamps
|
RAPID ACTION, SECURE HOLDING PIPE CLAMP FIXTURES
|
| #50 Pipe Clamp Fixture
...plus other(s)
|
THE FAMOUS "PONY®" #50 PIPE CLAMP FIXTURE ATTACHES TO ANY LENGTH OF 3/4" DIA. THREADED BLACK PIPE:
TAIL STOP HAS A MULTIPLE DISC CLUTCH THAT GRIPS THE PIPE AT ANY POINT BUT RELEASES, EASILY. 5/8" COLD DRAWN STEEL SCREW - 1-3/4" SQUARE CLAMP FACE. LOAD LIMITS - REGULAR PIPE 2,800 LBS., EXTRA HEAVY PIPE 3,800 LBS. (PIPE NOT INCLUDED). 125-025 - #52 FIXTURE HAS SIMILAR FEATURES BUT IS DESIGNED FOR 1/2" DIA. PIPE. 125-032 - PROTECT YOUR WORKPIECE WITH CLAMP PADS SPECIALLY DESIGNED FOR "PONY®" CLAMPS. SOLD IN SETS OF FOUR, THEY PROVIDE A PROTECTIVE CUSHION WITHOUT MARRING, STAINING, STICKING OR SLIPPING. 821-721 - ALSO SOLD IN SETS OF FOUR, CLAMP SADDLES HELP HOLD PIPE CLAMPS IN POSITION. USA.
|
|
|
|
Clamps And Vises - Bar & Pipe Clamps
|
PONY® DOUBLE PIPE CLAMP FIXTURES HOLD TIGHT
|
| #53 Double Pipe Clamp Fixture
|
THE "PONY"® #53 DOUBLE PIPE CLAMP FIXTURE IS HIGHLY RECOMMENDED FOR GLUING UP FLAT STOCK:
BY EXERTING EQUAL PRESSURE ON BOTH SIDES OF THE WORK, THE CLAMP ELIMINATES BUCKLING ENCOUNTERED WITH SINGLE PIPE CLAMPS. MALLEABLE IRON CASTINGS, 5/8" COLD DRAWN STEEL SCREW; 3-1/4" BETWEEN PIPES, 2-1/4" WIDE JAWS. ATTACHES TO TWO LENGTHS OF 1/2" DIA. THREADED BLACK PIPE (PIPE NOT INCLUDED). USA.
|
|
|
|
Clamps And Vises - Bar & Pipe Clamps
|
INNOVATIVE PIPE CLAMPS ELIMINATE NEED FOR THREADED PIPE
|
| 1/2" Irwin Pipe Clamp
...plus other(s)
|
IRWIN® QUICK-GRIP PIPE CLAMPS USE AN INNOVATIVE CLUTCH SYSTEM THAT ELIMINATES THE NEED FOR THREADED BLACK PIPE - LARGER CLUTCH PLATES ALLOW FOR EASIER RELEASE AND INCREASED DURABILITY AND DEPENDABILITY:
ERGONOMIC HANDLES OFFER EASIER CLAMPING WHILE LARGER FEET PROVIDE GREATER STABILITY AND CLEARANCE BETWEEN THE HANDLE AND WORKTOP. 128-027 MODEL 224212 - 1/2" (12MM) PIPE SIZE (PIPE NOT INCLUDED) - 1-1/2" (37MM) THROAT DEPTH, 8L X 1-3/4W X 4-1/2H, WEIGHS 2-1/2 LBS. 128-030 MODEL 224134 - 3/4" (19MM) PIPE SIZE (PIPE NOT INCLUDED) - 1-7/8" (47MM) THROAT DEPTH, 10L X 2W X 5-1/2H, WEIGHS 5 LBS. LIFETIME MANUFACTURER'S WARRANTY. IMPORTED.
|
|
|
|
Clamps And Vises - Bar & Pipe Clamps
|
CLUTCH-LOCK BAR CLAMPS PROVIDE I-BEAM STRENGTH
|
| 3-1/8"x6" Irwin Bar Clamp
...plus other(s)
|
IRWIN® QUICK-GRIP CLUTCH-LOCK BAR CLAMPS USE STEEL I-BEAM BARS TO REDUCE FLEXING AND BOWING AND ALLOW GREATER CLAMPING PRESSURE:
SOFT-GRIP HANDLE IS LARGER AND MORE ERGONOMIC, ALLOWING HIGHER CLAMPING PRESSURE WITH LESS EFFORT. 128-033 MODEL 223106 - 6" (15CM) CLAMPING CAPACITY, 3-1/8" (76MM) THROAT DEPTH, WEIGHS 2.2 LBS. 128-036 MODEL 223112 - 12" (30CM) CLAMPING CAPACITY, 3-1/8" (76MM) THROAT DEPTH, WEIGHS 2.5 LBS. 128-039 MODEL 223118 - 18" (45CM) CLAMPING CAPACITY, 3-1/8" (76MM) THROAT DEPTH, WEIGHS 2.9 LBS. 128-042 MODEL 223124 - 24" (60CM) CLAMPING CAPACITY, 3-1/8" (76MM) THROAT DEPTH, WEIGHS 3.2 LBS. 128-045 MODEL 223136 - 36" (91CM) CLAMPING CAPACITY, 3-1/8" (76MM) THROAT DEPTH, WEIGHS 3.9 LBS. LIFETIME MANUFACTURER'S WARRANTY. IMPORTED.
|
|
|
|
Clamps And Vises - Bar & Pipe Clamps
|
QUICK-GRIP® PASSIVE-LOCK BAR CLAMPS OFFER GREATER THROAT DEPTH
|
| 4-7/8"x12" Irwin Bar Clamp
...plus other(s)
|
IRWIN® QUICK-GRIP® PASSIVE-LOCK BAR CLAMPS FEATURE I-BEAM BARS TO REDUCE FLEXING AND BOWING AND ALLOW GREATER CLAMPING PRESSURE AND HAVE 35% GREATER THROAT DEPTH THAN COMPARABLE CLUTCH-LOCK CLAMPS:
SOFT-GRIP HANDLE IS LARGER AND MORE ERGONOMIC, ALLOWING HIGHER CLAMPING PRESSURE WITH LESS EFFORT. 128-048 MODEL 223212 - 12" (30CM) CLAMPING CAPACITY, 4-7/8" (12CM) THROAT DEPTH. 128-051 MODEL 223218 - 18" (45CM) CLAMPING CAPACITY, 4-7/8" (12CM) THROAT DEPTH. 128-054 MODEL 223224 - 24" (60CM) CLAMPING CAPACITY, 4-7/8" (12CM) THROAT DEPTH. 128-057 MODEL 223230 - 30" (75CM) CLAMPING CAPACITY, 4-7/8" (12CM) THROAT DEPTH. LIFETIME MANUFACTURER'S WARRANTY. USA.
|
|
|
|
Clamps And Vises - Bar & Pipe Clamps
|
BESSEY® UNIKLAMP JAWS REVERSE FOR USE AS A SPREADER
|
| 6" Uniklamp Clamp And Spreader
...plus other(s)
|
BESSEY® UNIKLAMP FEATURES JAWS ENCASED IN FIBERGLASS-REINFORCED POLYAMID AND A NON-MARRING, GLUE-RESISTANT SURFACE TO WITHSTAND PAINT AND SOLVENT:
"GENTLE TOUCH" JAWS DISTRIBUTE EVEN PRESSURE OVER 11 SQ. IN. CLAMPING SURFACE WHILE BUILT-IN FOOT KEEPS CLAMP EVEN AND PARALLEL ON WORK SURFACES. 550 LBS. CLAMPING PRESSURE - ALL HAVE A 3-1/8" NOMINAL THROAT DEPTH. LIFETIME MANUFACTURER'S WARRANTY. GERMANY.
|
|
|
|
Clamps And Vises - Bar & Pipe Clamps
|
BESSEY® TRADESMEN™ BAR CLAMPS - 9X FASTER THAN A "C" CLAMP™
|
| 4"x16" Tradesmen Bar Clamp
...plus other(s)
|
|
|
|
Clamps And Vises - Bar & Pipe Clamps
|
BESSEY® 3/4" PIPE CLAMP OFFERS A FIRMER GRIP
|
| 3/4" Pipe Clamp Fixture Set
|
THE BESSEY® PC-34 PIPE CLAMP FEATURES CLUTCH ACTION THAT "GRIPS," AUTOMATICALLY:
SIMPLY SCREW FIXED JAW, WITH HANDLE, ONTO THREADED END OF ANY LENGTH 3/4" DIA. BLACK PIPE AND PLACE SLIDING JAW ONTO OPPOSITE END (PIPE NOT INCLUDED). LARGE CLAMPING SURFACE PROVIDES POSITIVE GRIP; PROTECTIVE PADS PREVENT MARRING. LARGE CRANK HANDLE. PLATED SPINDLE RESISTS RUST AND CORROSION. 2-1/2 LBS. SHIPPING WEIGHT. LIFETIME MANUFACTURER'S WARRANTY. IMPORTED.
|
|
|
|
Clamps And Vises - Bar & Pipe Clamps
|
WORKING OVER LONGER DISTANCES IS MUCH EASIER WITH LIGHTNING CLAMP®
|
| Lightning Multipurpose Clamp
|
A CLAMPING, HOLDING AND SPREADING TOOL, THE PATENTED LIGHTNING CLAMP® AND SPREADER LETS YOU WORK OVER ALMOST ANY DISTANCE BY USING THREADED STEEL RODS JOINED TOGETHER WITH COUPLING NUTS:
TO CLAMP, MOVE THE SLIDING FACEPLATE UP TO THE WORK, LOCK ON AND TWIST THE HANDLE TO TIGHTEN. PULL THE LOCKING LEVER UP AND THE CLAMP RELEASES, INSTANTLY, EVEN UNDER FULL PRESSURE. REVERSE THE FACEPLATES FOR SPREADING. ONE-END ADJUSTING AND TIGHTENING MEANS QUICKER AND MORE EFFICIENT ONE-PERSON OPERATIONS. COMES WITH 1/2" DIA. X 24" LONG ROD (13TPI, 0.0833 PITCH UNC THREAD), COUPLING NUT AND INSTRUCTIONS. 5 LBS. NET WEIGHT; 5-1/2 LBS. SHIPPING WEIGHT. ONE-YEAR MANUFACTURER'S WARRANTY. IMPORTED.
|
|
|
|
Clamps And Vises - Bar & Pipe Clamps
|
REVOLUTIONARY DESIGNS GIVE YOU SERIOUS, ONE HANDED CLAMPING FORCE
|
| Jorg 6" Isd Bar/spreader Clamp
...plus other(s)
|
CONVENIENCE WITHOUT SERIOUS CLAMPING POWER THAT HAS ALWAYS BEEN THE TRADEOFF WITH ONE HANDED CLAMPS. ALL OF THAT HAS CHANGED WITH THE "JORGENSEN"® BAR/SPREADER CLAMP AND THE SPRING LOADED "PONY®" HAND CLAMP, WHICH OFFER QUICK, EASY, ONE HANDED CLAMPING PLUS THE PRESSURE YOU COULDNT APPLY BEFORE:
DURABLE COMPOSITE COMPONENTS FOR LONGER LIFE. HANDLES DESIGNED FOR COMFORT - NON-MARRING JAWS TO PROTECT YOUR WORK. OUR 6" CLAMP SET INCLUDES (2) 6" ONE HANDED BAR CLAMPS PLUS A 25' JORGENSON TAPE MEASURE
|
|
|
|
Clamps And Vises - Bar & Pipe Clamps
|
FOR PROFESSIONAL CABINETRY WORK IT'S HARD TO BEAT BESSEY® SLIP CLUTCH BAR CLAMPS
|
| Joiner Clamp 2-1/2" X 6"
...plus other(s)
|
DURABLE F-STYLE BESSEY® SLIP CLUTCH BAR CLAMPS ARE AN EXCELLENT CHOICE FOR GLUE-UPS AND ASSEMBLY THANKS TO A TWO-PIECE CLUTCH SYSTEM FOR EASIER OPENING AND CLOSING AND A ZINC-FINISHED STEEL RAIL FOR SMOOTHER TRAVEL:
PROTECTIVE PADS HELP MINIMIZE MARRING - RIVETED WOOD HANDLE PROVIDES A FIRMER GRIP. IMPORTED.
|
|
|
|
Advanced Search Tools
Browse
symbol next to the category that matches your desired product and select a sub-category link.
