|
|
|
Shop Accessories
|
3D SQUARES WILL HOLD YOUR PROJECT AT A PERFECT 90 DEGREES
|
| 3d Square Set Of 2
...plus other(s)
|
3D SQUARE POSITIONS AND HOLDS WORKPIECES - BOXES, DRAWERS, BOOK CASES, SHELVES, CABINETS, PICTURE FRAMES - AT A PERFECT RIGHT ANGLE, WHILE FREEING YOUR HANDS FOR FINAL FITTING AND GLUE UP:
3/16" THICK STAMPED ALUMINUM, MACHINED TO A 0.002" TOLERANCE ALONG EACH 6"L X 1-1/4"H LEG PROVIDES THE PRECISION OF AN ENGINEER'S SQUARE AT A FRACTION OF THE COST. SIMPLY CLAMP DIRECTLY ONTO YOUR PROJECT FOR PRECISE 90° ALIGNMENT (PREDRILLED HOLES ALLOW PERMANENT INSTALLATION). ALSO IDEAL AS A MITER GUIDE OR FOR CONSTRUCTING TABLESAW, ROUTER TABLE AND DRILL PRESS JIGS. SOLD IN PAIRS (CLAMPS NOT INCLUDED). 961-822 - 3D SQUARE AND CLAMP SET INCLUDES THE TWO PIECE 3D SQUARE SET PLUS FOUR 2-1/4 HIGH TENSION SPRING CLAMPS. USA..
|
|
|
|
Portable Power Tool Accessories - Routers & Trimmers
|
INCRA® WONDER FENCE
|
| Incra Wonder Fence 37
|
THE HEAVY DUTY INCRA® WONDER FENCE HAS BEEN DESIGNED FOR ALL ROUTING OPERATIONS, SHAPING, EDGE-FORMING AND PRECISION JOINERY. COMBINE WITH INCRA® JIG ULTRA OR TS-III TABLE SAW FENCE (SOLD SEPARATELY) FOR PRECISION JOINERY. USA.
HEAVY DUTY PRECISION MACHINED ALUMINUM SPLIT FENCE, WEDGES AND BASE FENCE. INFEED AND OUTFEED FENCES INDEPENDENTLY ADJUSTABLE IN 0.002" STEPS OVER 1/8" RANGE. LASER ENGRAVED OFFSET SCALE. EACH OFFSET MECHANISM HAS ITS OWN CURSOR AND SCALE MARKED OFF IN 0.002" INCREMENTS. LOCK-DOWN OFFSET PERMITS GAP ADJUSTMENT. ADJUSTABLE FENCE GAP WIDTH TO 4-1/2". HI-RISE™ RAISED PANEL CAP FOR VERTICAL PANEL RAISING. BUILT-IN DUST COLLECTION PORT WITH ATTACHMENT ELBOW. ALL ALUMINUM CONSTRUCTION; FULLY ASSEMBLED.
|
|
|
|
Portable Power Tool Accessories - Rotary Tools
|
BOSCH 18 VOLT CORDLESS ROTOZIP® SPIRAL SAW® RUNS AT AN IMPRESSIVE 30,000 RPM
|
| Rotozip Jigsaw Handle
...plus other(s)
|
|
|
|
Portable Power Tool Accessories - Jigs And Fixtures
|
SUPER STRONG, CLEAR ROUTER SUB-BASES AND SAW INSERTS
|
| 11-7/8" Sq 1/4" Clear Lexan
...plus other(s)
|
|
BUILD EXTRA BASEPLATES FOR ROUTERS, INSERTS FOR TABLES, SEE THROUGH FIXTURES AND CUSTOM FIXTURES OF ALL KINDS. OR MAKE PROJECTS USING THESE CLEAR, LEXAN® POLYCARBONATE 11-7/8" SQUARES. USA.
|
|
|
|
Portable Power Tool Accessories - Jig Saws
|
BOSCH POWER HANDSAW PUTS THE FINISHING TOUCHES ON ALL PROJECTS
|
| 5-3/4" 20tpi Sawblade For 1640vs
...plus other(s)
|
|
|
|
Portable Power Tool Accessories - Jig Saws
|
ADD NEW LIFE TO YOUR DISCONTINUED BOSCH IN-LINE GRIP JIGSAW WITH GENUINE BOSCH ACCESSORIES
|
| 90 Degree Miter Guide
...plus other(s)
|
WHILE IT MIGHT STILL BE POSSIBLE TO FIND BLADES FOR BOSCH IN-LINE GRIP JIGSAWS, LIKE MODELS B4050 OR THE 3294EVS SHOWN, LOCATING THE GENUINE BOSCH ACCESSORIES THAT MAKE THESE TOOLS TRULY VERSATILE CAN BE MUCH MORE DIFFICULT. THAT'S WHY WOODWORKER'S SUPPLY® IS MAKING ITS REMAINING STOCKS OF THESE ACCESSORIES AVAILABLE AT GREATLY REDUCED PRICES:
898-703 - T321SB WIRE BRUSH, 9" OAL, 6-1/2" LONG BRUSH, BOSCH T-SHANK. 898-710 - T323GB FIBER BRUSH, 9" OAL, 6-1/2" LONG BRUSH, BOSCH T-SHANK. 898-717 - JA1202 45° MITER GUIDE. 898-724 - JA1201 90° MITER GUIDE. 898-731 - JA1203 GUIDE FENCE AND CIRCLE ATTACHMENT, 6-1/4" RADIUS (REQUIRES 90° MITER GUIDE TO ATTACH TO TOOL). SWITZERLAND.
LIMITED TO QUANTITIES ON HAND
|
|
|
|
Machinery Accessories - Table Saws
|
WOODWORKER'S SUPPLY® DELTA® UNISAW® ACCESSORY PACKAGES
|
| Universal Tenoning Jig
...plus other(s)
|
|
|
|
Machinery Accessories - Table Saws
|
INCRA® 18" MITER SLIDER
|
| Incra 18" Miter Slider & Plans
|
THE INCRA® 18" MITER SLIDER HAS AN ALUMINUM RUNNER THAT ADJUSTS FOR PERFECT SLIDING ACTION IN ANY 3/4" X 3/8" MITER SLOT. OR, IT CAN BE LOCKED INTO PLACE FOR OTHER OPERATIONS. WON'T WARP, SHRINK OR SWELL LIKE WOODEN RUNNERS. FREE, ILLUSTRATED PLANS SHOW HOW TO BUILD A VARIETY OF SHOP MADE TABLESAW JIGS. USA. PLANS INCLUDE:
CROSSCUT BOX - BOX FIRMLY SUPPORTS STOCK OFF OF TABLE SURFACE FOR SMOOTH CUTS, WHILE MAINTAINING PERFECTLY SQUARE CUTS. MITER JIG - JIG GUARANTEES ACCURATE AND REPEATABLE 45° CUTS WITHOUT INCONVENIENCE OF SETTING UP MITER GAUGE, TILTING THE BLADE OR TRIAL AND ERROR CUTS. FEATHER BOARD - FEATHER BOARD LOCKS INTO MITER SLOT TO HOLD STOCK FIRMLY AGAINST RIP FENCE.
|
|
|
|
Machinery Accessories - Table Saws
|
TAPERING JIG FOR TABLE SAW
|
| Tapering Jig
|
USING A WOODTEK® TAPER JIG ENSURES COMPLETE CONTROL OF ANGLED CUTS ON RADIAL ARM, BAND OR TABLE SAWS:
24" LONG ALUMINUM JIG CONVERTS TO RIGHT- OR LEFT-HAND USE AND ADJUSTS UP TO 15° (3" PER FOOT). JIG RIDES AGAINST SAW FENCE - USE IS SIMILAR TO EVERYDAY RIPPING. EASY-TO-READ SCALE MAKES ADJUSTMENTS QUICK AND SIMPLE. WORKS WITH DADO AND MOLDING HEADS, TOO. EASY TO ASSEMBLE - ALL HARDWARE INCLUDED. IMPORTED.
|
|
|
|
Machinery Accessories - Table Saws
|
DELTA® SLIDING JIG PROVIDES GREATER ACCURACY DURING A VARIETY OF SHAPING OPERATIONS
|
| Sliding Shaper Jig
|
THE DELTA® 43-188 SLIDING SHAPER JIG SPEEDS PRODUCTION OF RAISED PANELS, STILES AND RAILS SINCE HANDS ARE KEPT AWAY FROM THE CUTTER AND WOOD IS FED CONSISTENTLY AND SMOOTHLY:
THREE GUIDE BAR LOCATIONS FOR POSITIONING THE WORKPIECE AS CLOSE AS POSSIBLE TO BOTH LARGER AND SMALLER DIAMETER SHAPER CUTTERS. 12 MOUNTING HOLES OFFER YOU A DOZEN OPTIONS FOR MOVING THE SOLID STEEL BARS AND CAM ACTION CLAMPS AROUND THE CAST IRON BASE IN ORDER TO FIT LARGE OR SMALL WORKPIECES, DIFFERENT MACHINES AND VARIOUS TYPES OF OPERATIONS. LARGE, EASY GRIP HANDLE ADJUSTS TO LEFT AND RIGHT OF MITER GAUGE FOR MORE VERSATILE SETUPS. NOT JUST FOR SHAPERS, THE JIG WILL ALSO HELP YOU SAFELY CUT ANGLED TENONS, TENONS AND DADOS ON EITHER LEFT OR RIGHT TILTING TABLESAWS. 13 LBS. NET WEIGHT; 15 LBS. SHIPPING WEIGHT. TWO-YEAR MANUFACTURER'S WARRANTY. IMPORTED.
|
|
|
|
Machinery Accessories - Table Saws
|
UNIVERSAL TABLE SAW JIG FOR EXACT, SAFE, CONTROLLED CUTTING
|
| Universal Table Saw Jig
...plus other(s)
|
USING THE MITER GAUGE SLOT IN YOUR TABLE SAW AND THE UNIVERSAL TABLE SAW JIG YOU CAN FEED WORK SAFELY AND PRECISELY INTO THE SAW BLADE:
SAFELY CUT FLAWLESS TENONS, LAP JOINTS, SPLINE JOINTS AND TONGUE AND GROOVE JOINTS. SINCE YOU CAN CLAMP SMALL WORKPIECES, CUTTING THEM CLOSE IS FAR SAFER THAN USING PUSH BLOCKS. ENTIRE JIG ROTATES 90° FOR EASY RIGHT ANGLE CUTOFFS OF SMALL WORKPIECES. 6-1/2"H X 7" SQUARE DIE CAST ALUMINUM, WEIGHS 5 LBS. INCLUDES FOUR STEEL LOCATING PINS WITH WASHERS AND WING NUTS, TWO DIE CAST ALUMINUM CLAMPS WITH HEX HEAD BOLTS AND INSTRUCTIONS. ALSO WORKS ON ROUTER TABLES AND SPECIALITY JIGS WITH STANDARD MITER GAUGE SLOTS. IMPORTED.
|
|
|
|
Machinery Accessories - Table Saws
|
WOODWORKER'S PERMANENT MAGNET MAGJIG AND MAGSQUARE OFFER UNMATCHED WORK AND JIG HOLDING CAPABILITIES
|
| 95 Lbs. Switchable Magnet
...plus other(s)
|
PATENTED MAGSWITCH™ MAGJIG AND MAGSQUARE ARE REVOLUTIONARY, EASY-TO-INSTALL IMPROVEMENTS THAT YOU CAN USE TO CUSTOMIZE HOW YOU SET UP TOOLS, USE JIGS OR HOLD WORK IN PLACE:
PLACE ONTO ANY STEEL OR SMOOTH CAST IRON TABLE, BED OR FENCE, TURN THE KNOB "ON" TO ACTIVATE THE MAGNETIC FIELD AND THEY VIRTUALLY LOCK INTO PLACE; TURN KNOB "OFF" TO RELOCATE OR REMOVE, EASILY.
DESIGNED FOR 3/4" THICK MATERIAL, MAGJIG (TWO OR MORE RECOMMENDED PER JIG) INSTALLS BY SIMPLY BORING A 30MM OR 40MM HOLE. IT CAN BE MOVED TO OTHER JIGS OR FASTENED INTO PLACE USING PRE-DRILLED HOLES:
20MM MAGJIG (SHOWN): 1-7/8"H X 1-5/16"W X 2-1/4"L; WEIGHS 5 OZ. - 95 LBS. HOLDING POWER. 30MM MAGJIG: 2-1/16"H X 1-3/4"W X 2-5/8"L; WEIGHS 9 OZ. - 155 LBS. HOLDING POWER.
FEATURING PRE-TAPPED MOUNTING HOLES ON ALL SIDES, MAGSQUARE HAS 90° CORNERS FOR SQUARING:
30MM MAGSQUARE: 1-1/2" SQUARE X 2-3/4"H; WEIGHS 11.6 OZ. - 145 LBS. HOLDING POWER (10-32 THREADS). 50MM MAGSQUARE: 2-1/2" SQUARE X 3-1/2"H; WEIGHS 3-1/2 LBS. - 500 LBS. HOLDING POWER (1/4-20 THREADS - DO NOT USE FOR LIFTING).
INSTRUCTIONS INCLUDED (MOUNTING HARDWARE NOT INCLUDED). IMPORTED.
|
|
|
|
Machinery Accessories - Table Saws
|
LOW PROFILE MJ SPLITTER™ ENSURES ACCURATE TABLESAW CUTTING AND HELPS ELIMINATE KICKBACK
|
| Mj Splitter Kit, Regular Kerf Saw Blade
...plus other(s)
|
SPECIFICALLY DESIGNED FOR MOUNTING INTO ZERO CLEARANCE TABLESAW INSERTS THAT HAVE NO EXISTING SPLITTER OPENING, THE MICROJIG MJ SPLITTER™ HELPS PREVENT BINDING AND TWISTING THAT CAN RESULT IN BURNED BOARDS AND DANGEROUS KICKBACK:
MULTIPLE ALIGNMENT SURFACES GENERATE SLIGHT TENSION - LIKE A MINI FEATHERBOARD - JUST BEHIND THE SAWBLADE. FOOLPROOF INSTALLATION - ONCE IN PLACE, SPLITTERS ARE EASILY INSERTED OR REMOVED BY HAND. 138-329 - SP-0125 USE WITH STANDARD KERF 10" SAWBLADES; 0.118" TO 0.145" RANGE. 138-332 - SP-0100TK FOR THIN KERF 10" SAWBLADES; 0.090" TO 0.118" RANGE. EACH INCLUDES TWO SPLITTERS, DRILL GUIDE, DRILL BIT, FOUR WOOD SCREWS AND COMPLETE INSTRUCTIONS. 90° CUTS ONLY - WILL NOT WORK WITH A TILTED ARBOR. USE WITH OR WITHOUT MICROJIG GRR-RIPPER® SYSTEM 122-372. ONE YEAR MANUFACTURER'S WARRANTY. USA.
TO HELP COMPLETE YOUR PURCHASE, MAY WE SUGGEST:
RED PLASTIC ZERO CLEARANCE INSERT FOR CRAFTSMAN® TABLESAWS 95-610. MAKE YOUR OWN INSERT USING THE CORRECT THICKNESS OF UHMW PLASTIC 836-990.
|
|
|
|
Machinery Accessories - Table Saws
|
FEED WORK PARALLEL TO THE SAWBLADE AND ELIMINATE BARE HAND FEEDING WITH GRR-RIPPER®
|
| Grr-ripper Table Saw Push Block System
|
GRR-RIPPER® GRR-200 IS A HAND TOOL THAT GRIPS BOTH SIDES OF STOCK DURING CUTTING OPERATIONS, MAINTAINING BALANCED PARALLEL FEEDING, GREATLY INCREASING THE ACCURACY OF CUTS AND ELIMINATING BURNING AND KICKBACK:
STOCK IS COMPLETELY ENCLOSED AS IT PASSES ALONG THE RIP FENCE TOWARDS THE BLADE, PROTECTING HANDS AND FINGERS FROM CUTTING EDGES. MULTIPLE GROOVED, NON-SLIP PADS PROVIDE SUPERIOR GRIPPING - 8 ADJUSTABLE/DETACHABLE COMPONENTS CAN BE USED ON TABLESAWS, ROUTER TABLES, SHAPERS OR JOINTERS. USE FOR RESAWING, AS A PUSH BLOCK, CUSTOM JIG, HOLD DOWN, SPLITTER, NAVIGATOR OR ANY OF MANY OPTIONS - FULLY ADJUSTABLE. COMPLETE INSTRUCTIONS INCLUDED. ONE YEAR MANUFACTURER'S WARRANTY. USA.
|
|
|
|
Machinery Accessories - Table Saws
|
WOODTEK 116738 TENONING JIG
|
| Tenoning Jig
|
THE WOODTEK® HEAVY DUTY TENONING JIG FITS LEFT AND RIGHT TILTING TABLESAWS WITH 3/8" X 3/4" MITER GROOVES:
CRANK HANDLE ENSURES FAST AND EASY CLAMPING OF STOCK UP TO 3-1/4" THICK. CUT WIDTH IS CONTROLLED WITH THREADED ADJUSTMENT KNOB. ADJUSTABLE 90° POSITIVE STOP FOR REPETITIVE CUTS; 90-45° BACK STOP HAS ADJUSTABLE 90° POSITIVE STOP FOR ANGULAR STOCK. LARGE HANDLES HELP ENSURE OPERATING CONTROL AND USER SAFETY. CAST IRON AND STEEL CONSTRUCTION. APPROXIMATELY 9-1/4"H X 10-1/2"D X 20"W; WEIGHS 20 LBS. SOME ASSEMBLY REQUIRED. ONE YEAR PARTS AND WORKMANSHIP WARRANTY. IMPORTED.
|
|
|
|
Hardware Electronic - Accessories
|
POWER GROMMET PROVIDES SIMPLE CONNECTIVITY FOR PORTABLE DEVICES
|
| Power Tap Grommet
|
POWER TAP GROMMET ALLOWS EASY ACCESS TO POWER AND DATA CABLES AND THEN NEATLY SWIVELS CLOSED TO LEAVE A CLEAN WORK SURFACE. LATCHES IN BOTH OPEN AND CLOSED POSITIONS.
THIS GROMMET IS THE IDEAL ADDITION TO CONFERENCE TABLES, WORKSTATIONS AND DESKTOPS. GROMMET HOUSES THREE 125 VOLT, 15 AMP GROUNDED AC OUTLETS TO POWER PORTABLE DEVICES AND CHARGERS, AND TWO SEPARATE CAT 5 ETHERNET JACKS TO ALLOW ACCESS TO NETWORK DATA THROUGH STANDARD RJ45 CONNECTORS. POWER CORD IS 14/3 CONDUCTOR, 8' LONG. CONSTRUCTED OF DURABLE, FIRE RESISTANT ABS. UL AND CUL LISTED. 4-3/8" OUTER RING DIAMETER. REQUIRES A 4.21" (107MM) DIAMETER HOLE FOR MOUNTING TO SURFACE. EASILY CUT WITH ADJUSTABLE CIRCLE CUTTER OR JIGSAW. ONE YEAR MANUFACTURER'S WARRANTY.
|
|
|
|
Books
|
JIGS & FIXTURES FOR THE TABLE SAW & ROUTER©
|
| Jigs & Fixtures For The Tablesaw
|
WITH THE 26 INGENIOUS PROJECTS INSIDE OF JIGS & FIXTURES FOR THE TABLE SAW & ROUTER© YOU CAN HARNESS THE POTENTIAL OF YOUR POWER TOOLS WHILE ALSO DISPLAYING YOUR WOODWORKING CRAFTSMANSHIP:
TABLE SAW PROJECTS INCLUDE A SHOP BUILT PANEL SAW, PRECISION CROSSCUTTING JIG AND OUTFEED/ASSEMBLY TABLE. ROUTER PROJECTS INCLUDE A TRAVELING ROUTER TABLE, HORIZONTAL ROUTING SYSTEM AND THE ULTIMATE FLUTING JIG. EACH IS ACCOMPANIED BY DETAILED PLANS, EXPERT INSTRUCTIONS AND HELPFUL HINTS TO ENSURE YOUR FINISHED PRODUCTS ARE WELL BUILT AND ARE PRODUCTIVE ENHANCEMENTS TO YOUR TABLE SAW AND ROUTER. 8-1/2" X 11" SOFTCOVER. 160 PAGES W/COLOR PHOTOS, DIAGRAMS AND TECHNICAL AND EXPLODED DRAWINGS.
|
|
|
|
Advanced Search Tools
Browse
will