|
|
|
Hardware Shelf And Support - Brackets
|
CREATE A WORK SURFACE THAT SIMPLY FOLDS OUT OF THE WAY FOR STORAGE
|
| 12" Folding Bracket
...plus other(s)
|
STURDY KNAPE & VOGT® FOLDING SHELF BRACKETS SUPPORT UP TO 750 LBS. PER PAIR WHEN PROPERLY INSTALLED:
BRACKETS LOCK AT 90°, 80° AND 70° FOR CONVENIENT VERSATILITY AND 0° FOR OUT-OF-THE-WAY STORAGE. PERFECT FOR LAUNDRY ROOMS, CRAFT AREAS, PLAYROOMS, BEDROOMS AND DRAWING TABLE APPLICATIONS. DURABLE ZINC-COATED STEEL WITH SPRING-LOADED RELEASE LEVER. NOTE: TO ACHIEVE 750 LBS. PER PAIR CAPACITY, MANUFACTURER RECOMMENDS INSTALLING EACH BRACKET WITH THREE #10 X 2" PAN HEAD SCREWS, FASTENED INTO 2 X 4 WOODEN WALL STUDS AT 16" ON CENTER.
|
|
|
|
Hardware Shelf And Support - Brackets
|
HEAVY DUTY WORK STATION BRACKETS PERFECT FOR WORKBENCHES, COMPUTERS AND MUCH MORE
|
| 12x18 Rev Brackets Black
...plus other(s)
|
HIGH QUALITY, CANTILEVER WORK STATION BRACKETS ARE FABRICATED FROM 1/8" STEEL WITH WHITE OR BLACK TEXTURED POWDER COAT FINISHES - EASILY CREATE STRONG WORK SURFACES WITHOUT CUMBERSOME LEGS TO GET IN THE WAY:
AVAILABLE IN FOUR SIZES; REVERSIBLE DESIGN MAKES THEM VERSATILE AND EASIER TO USE. 3" X 3" - 45° NOTCHES ALLOW FOR STANDARD WALL CLEATS AND WIRE RUNS. MULTIPLE 1/4" DIA. MOUNTING HOLES PER SIDE (MOUNTING HARDWARE NOT INCLUDED). PACKAGED IN EQUAL QUANTITIES OF "RIGHTS" AND "LEFTS". IMPORTED.
|
|
|
|
Hardware Shelf And Support - Brackets
|
EASY LEVELING SHELF AND COUNTER BRACKETS
|
| 8"x11" Easy Level Bracket-wh
...plus other(s)
|
UNLIKE CONVENTIONAL SHELF BRACKETS, PATENT PENDING EASY LEVELING SHELF AND COUNTER BRACKETS CAN BE ADJUSTED TO MAKE SHELVES, COUNTERTOPS OR WORKSTATIONS LEVEL - ONCE ALIGNED, TOP AND BOTTOM SECTIONS BOLT TOGETHER SECURELY:
TESTED TO SUPPORT UP TO 640 LBS. WHEN ATTACHED FIRMLY TO WOOD STUDS, 16" ON CENTER. 19", 21" AND 27" BRACKETS HAVE A 1-3/8" DIA. PUNCHED HOLE FOR ROUTING CABLES, WIRING OR AIR LINES. WORK WITH 3/4" X 1-1/2" OR 1-1/2" X 1-1/2" CLEATS. NO CROSS BRACE REQUIRED. EASY ACCESS TO WALL ANCHOR SCREWS. WHITE OR BLACK POWDER COATED STEEL - SURFACE CAN BE PAINTED TO MATCH DECOR. ANSI/BHMA TESTED. ASSEMBLY HARDWARE AND MOUNTING INSTRUCTIONS INCLUDED. IMPORTED.
|
|
|
|
Hardware Shelf And Support - Brackets
|
WOODTEK USA® SUPER HEAVY DUTY SHELF STANDARDS AND BRACKETS
|
| 24" Hd Shelf Standard
...plus other(s)
|
WOODTEK USA® SUPER HEAVY DUTY SHELVING STANDARDS AND BRACKETS ARE FORMED FROM 3/16" THICK, HEAVY GAUGE STEEL TO SAFELY HOLD HEAVY LOADS:
WHEN PROPERLY INSTALLED ONTO THE 24" LONG STANDARDS, 10" AND 18" BRACKETS CAN EACH SUPPORT UP TO 500 LBS., 1" FROM THE TIP. BLACK POWDER-COAT FINISH FOR DURABILITY. STANDARDS ARE PREDRILLED FOR 3/8" DIA. FASTENERS (FASTENERS NOT INCLUDED>). USA."
|
|
|
|
Hardware Shelf And Support - Brackets
|
KV 187LL SHELF BRACKET WITH LOCK
|
| 12" Kv187ll Shelf Bracket-ano
|
|
|
|
Hardware Shelf And Support - Brackets
|
KNAPE & VOGT® 71/170 STANDARDS AND BRACKETS FOR SPECIALTY APPLICATIONS
|
| 8" Kv170 Shelf Bracket
...plus other(s)
|
KNAPE & VOGT® KV71 ANOCHROME™ NARROW FACE SHELVING STANDARDS COME IN FOUR LENGTHS WITH A FINISH THAT RESISTS RUST AND OXIDATION:
DURABLE 16 GAUGE STEEL, 5/16"W X 13/32"H ( MOUNTING SCREWS NOT INCLUDED). COMPATIBLE WITH KV170 ANOCHROME™ BOLTLESS BRACKETS, WHICH FIT AND SNAP INTO STANDARDS. ALSO COMPATIBLE WITH KV80 STANDARDS.
|
|
|
|
Hardware Shelf And Support - Brackets
|
KNAPE & VOGT® KV144 ANOCHROME™ MIRROR STANDARDS SUPPORT BOTH MIRRORS AND SHELVES
|
| 48" Mirror Standard
...plus other(s)
|
DESIGNED FOR MIRRORED WALL SHELVING APPLICATIONS, KNAPE & VOGT® KV144 ANOCHROME™ MIRROR STANDARDS COME IN THREE LENGTHS OF DURABLE STEEL WITH A FINISH THAT RESISTS RUST AND OXIDATION:
1.13" FACE X 0.31" THICK; MIRRORS ARE HELD IN PLACE BY 0.25" OVERHANG ON EACH SIDE OF STANDARD - NOTCHES ACCOMMODATE SHELF BRACKETS (NOT INCLUDED). 48", 60" AND 72" LENGTHS (MOUNTING SCREWS NOT INCLUDED).
LIMITED TO QUANTITIES ON HAND
TO HELP COMPLETE YOUR PROJECT, MAY WE SUGGEST:
830-690 - KNAPE & VOGT® KV180 ANOCHROME™ SHELF BRACKETS.
|
|
|
|
Hardware Shelf And Support - Brackets
|
QUICKLY AND EASILY ELIMINATE ANNOYING SUB-FLOOR SAGS OR SEAMS
|
| Seam-ender
...plus other(s)
|
|
|
|
Hardware Shelf And Support - Brackets
|
SHELF BRACKETS THAT FOLD OUT OF THE WAY
|
| Folding Shelf Bracket-12"
...plus other(s)
|
GREAT ANYWHERE WHERE SHELVES NEED TO FOLD OUT OF THE WAY:
12" AND 8" STEEL BRACKETS AUTOMATICALLY LOCK INTO POSITION; LIFT THE SHELF AND THEY UNLOCK. GREY ENAMEL FINISH. SOLD IN PAIRS. USE #10 SCREWS (NOT INCLUDED).
|
|
|
|
Hardware Shelf And Support - Brackets
|
FOLDING SHELF BRACKETS HOLD UP TO 88 LBS. PER PAIR
|
| Folding Shelf Bracket
|
10" LONG FOLDING SHELF BRACKETS LOCK OPEN TO HOLD SHELVES UP TO 12" WIDE:
RELEASE BUTTON LETS SHELF FOLD DOWN AND OUT OF THE WAY WHEN NOT IN USE. YELLOW CHROMATE FINISH. MOUNT TO SHELVING WITH #8 SCREWS (NOT INCLUDED). SOLD IN PAIRS. IMPORTED
|
|
|
|
Hardware Shelf And Support - Pilasters & Standards
|
KNAPE & VOGT® SHELVING SYSTEM SUPPORTS UP TO 450 POUNDS
|
| 48" Kv82 Shelf Standard-black
...plus other(s)
|
THE KNAPE & VOGT® SERIES 82/182 SHELVING SYSTEM IS A GREAT CHOICE WHERE APPEARANCE AND STRENGTH ARE CRITICAL - IDEAL FOR SCHOOLS, HOSPITALS, OFFICES AND EVEN HOMES. SMOOTH, ROUNDED CORNERS GIVE A SOFTER AND LESS INTRUSIVE LOOK WHILE ALL-METAL, DUAL-TRACK STANDARDS AND "U"-SHAPED BRACKETS EASILY SUPPORT HEAVY LOADS - WHITE OR BLACK EPOXY FINISHES:
KV® 82 STANDARDS ARE 1.05" WIDE, PROJECT 0.69" AND ARE AVAILABLE IN 48", 72" AND 96" LENGTHS. UNIQUE COVER STRIPS PROVIDE A CLEAN AND APPEALING APPEARANCE. KV® 182 BRACKETS ARE 0.53" WIDE AND FASTEN ONTO STANDARDS USING LUGS. 5" LONG BRACKETS SUPPORT 425 LBS., 7" - 360 LBS., 9" - 370 LBS., 10-1/2" - 330 LBS., 12-1/2" - 300 LBS., 14-1/2" - 450 LBS., 18-1/2" - 400 LBS., 22-1/2" - 400 LBS. BOOKENDS SNAP-FIT INTO STANDARDS. 7" LONG UNIT IS 4-1/2" HIGH; 9" AND 10-1/2" ARE 5-3/4" HIGH. SHELF LOCATORS/JOINERS MOUNT ONTO SHELF BOTTOM TO STABILIZE SHELF ON BRACKETS, WHILE ALLOWING EASY REMOVAL (4 LOCATORS/JOINERS AND 8 SCREWS). WALL STANDARD SCREWS FASTEN STANDARDS ONTO WALLS (6, 2" LONG FLAT HEAD SCREWS, 6 WALL ANCHORS, 6 COVER TABS). SHELF BRACKET SCREWS ANCHOR SHELVES DIRECTLY ONTO BRACKETS (6, EACH, 1", 2" AND 3-1/8" LONG OVAL HEAD TAPPING SCREWS). NOTE: STANDARDS, BRACKETS, BOOKENDS AND HARDWARE SOLD SEPARATELY - SHELVES NOT INCLUDED. ALSO AVAILABLE IN BLACK OR WHITE, DISCONTINUED, TWIN-SLOT KNAPE & VOGT® SERIES E3200 HEAVY-DUTY SHELVING STANDARDS CAN BE INSTALLED USING 182 BRACKETS AND MOUNTING HARDWARE (NOT INCLUDED) - LIMITED TO QUANTITIES ON HAND. LIFETIME MANUFACTURER'S WARRANTY. USA.
|
|
|
|
Hardware Shelf And Support - Pilasters & Standards
|
THIN PROFILE ALUMINUM SHELF STANDARD GIVES A CLEAN FINISHED LOOK TO SHELVING
|
| 1820mm Low Profile Surf Mount Standard
...plus other(s)
|
LOW PROFILE ALUMINUM SHELF STANDARDS UPGRADE THE LOOK OF ADJUSTABLE SHELVING:
THE SURFACE MOUNT VERSION OF THESE 1820MM (71-21/32") LONG THIN PROFILE ALUMINUM SHELF STANDARDS IS ONLY 3MM (1/8") THICK AND 10MM WIDE. STANDARDS FASTEN TO UPRIGHT SURFACE WITH COLOR COORDINATED MOUNTING SCREWS FOR A VERY CLEAN LOOK. SCREW HOLES ARE LOCATED EVERY 120MM (4-47/64") GIVING 16 SCREW HOLES PER STANDARD. SHELF SUPPORTS FIT INTO SPECIALLY FORMED OPENINGS WHICH KEEP THE SUPPORTS FROM FALLING OUT OF THE STANDARDS. SHELF SUPPORTS ARE MADE FROM 430 STAINLESS STEEL AND HAVE A VERY THIN PROFILE WHICH ELIMINATES DEAD SPACE AT THE BOTTOM OF THE BRACKET. THE BRACKETS MEASURE 20MM X 20MM X 10MM WIDE (51/64" X 51/64" X 3/8") A RUBBER CAP IS AVAILABLE FOR THE SHELF SUPPORTS THAT CUSHIONS GLASS SHELVING OR CAN BE USED TO SECURE WOODEN SHELVES. THE RUBBER CAP CAN BE MOUNTED WITH EITHER THE FLAT OR RAISED PORTION UP. OPTIONAL GREY ABS END CAPS SCREW ON TO COVER THE OPEN ENDS OF THE STANDARDS. THE 1820MM MORTISE IN VERSION OF THE SHELF STANDARDS MOUNTS INTO A 10MM WIDE X 6MM DEEP RABBET. THIS STANDARD HAS A 12MM WIDE FACE WHICH GIVES A CLEAN TRIMMED APPEARANCE WHEN MOUNTED. FIT TIGHTNESS MAY VARY DEPENDING ON THE MATERIAL INTO WHICH IT IS MOUNTED - WOOD GLUE CAN BE APPLIED TO THE RIBBED EDGES FOR A MORE SECURE MOUNT. 3MM X 16MM MOUNTING SCREWS ARE PACKED 100 PER BOX. JAPAN
|
|
|
|
Hardware Shelf And Support - Pilasters & Standards
|
COVERED SHELF SUPPORTS
|
| 1820mm Covered Shelf Standard-s/s
...plus other(s)
|
LOW PROFILE STAINLESS STEEL SHELF SUPPORTS SHOW NO MOUNTING SCREWS AND NO ADJUSTMENT SLOTS WHEN OPTIONAL COVER STRIPS ARE IN PLACE. LOW PROFILE 1820MM (71-21/32") STAINLESS STEEL SHELF SUPPORTS SHOW NO MOUNTING SCREWS AND NO ADJUSTMENT SLOTS WHEN OPTIONAL COVER STRIPS ARE IN PLACE:
MADE FROM SATIN FINISHED 430 STAINLESS STEEL FOR DURABILITY, THESE SUPPORTS ARE FORMED WITH CLIP MOUNTING SLOTS SPACED 15MM APART ALONG THE LENGTH OF THE STANDARD. THE TWO PIECE SHELF CLIPS HAVE A STAINLESS STEEL FRAME AND A SOFT PLASTIC (ELASTOMER) INSERT TO HOLD THE SHAPE AND CREATE A SECURE FIT INTO THE SIDE CHANNELS OF THE STANDARDS. TO INSTALL THE CLIPS, REMOVE THE PLASTIC INSERT, SQUEEZE THE CLIP FRAME AND INSERT INTO THE STANDARD; REINSERTING THE PLASTIC INSERT LOCKS THE SHELF CLIP IN PLACE. SHELF CLIPS ARE AVAILABLE WITH EITHER WHITE OR BROWN PLASTIC (ELASTOMER) INSERTS. STANDARDS CAN BE FASTENED TO UPRIGHT SURFACES USING #5X1/2" OR #5X3/4" FLAT HEAD WOOD SCREWS. (EACH STANDARD HAS 11 COUNTERSUNK SCREW HOLES.) WHITE OR BROWN OVER STRIPS ARE 1820MM (71-21/32") PVC PLASTIC AND PRESS FIT INTO THE STANDARDS FTO CONCEAL THE MOUNTING SCREWS. SCREW-ON POLYPROPYLENE END CAPS HAVE A HINGED FLAP THAT HIDES THE MOUNTING SCREW. ALL COMPONENTS ARE SOLD EACH. JAPAN. TO HELP COMPLETE YOUR PROJECT, MAY WE SUGGEST:
#5 X 1/2" FH SCREWS - 800-525. #5 X 3/4" FH SCREWS - 800-526.
|
|
|
|
Hardware Shelf And Support - Pilasters & Standards
|
ADJUSTABLE, DURABLE KNAPE & VOGT® KV180 SHELVING BRACKETS DESIGNED FOR KV80 STANDARDS
|
| 36" Kv80 Anochrome Shelf Standard
...plus other(s)
|
KNAPE & VOGT® 16 GAUGE STEEL KV180 SHELF BRACKETS ARE AVAILABLE IN ELECTROPLATED ANOCHROME™ OR POWDER COATED BLACK OR WHITE FINISHES:
AVAILABLE IN 8" TO 20" LENGTHS - ADJUSTABLE ON 1" CENTERS. DESIGNED TO FIT AND SNAP INTO KV80 SHELF STANDARDS (ORDER SEPARATELY) FOR SECURE SUPPORT. USA.
|
|
|
|
Hardware Shelf And Support - Pilasters & Standards
|
KNAPE & VOGT® 83/183 OVERSIZE STANDARDS AND FLANGED BRACKETS FOR LONG RUNS OF SHELVING
|
| 48" Kv83 Shelf Standard-ano
...plus other(s)
|
DESIGNED FOR EXTRA-LONG APPLICATIONS, KNAPE & VOGT® KV83 OVERSIZE SHELVING STANDARDS AND BRACKETS COME IN FIVE LENGTHS WITH A FINISH THAT RESISTS RUST AND OXIDATION:
KV83 STANDARDS ARE MADE FROM 16GA STEEL, 3/4" WIDE X 1/2" HIGH - COMPATIBLE WITH ALL KV® SHELF BRACKETS FOR USE IN 1" ADJUSTMENT STANDARDS. BRACKETS ARE AVAILABLE IN CENTER (FLANGED BOTH SIDES) AND STYLES FOR LEFT- OR RIGHT-HAND SHELF ENDS. KV183 BRACKETS HAVE A WIDE FLANGE TO ALLOW BETTER FASTENING OF SHELF MATERIAL TO BRACKETS. ANOCHROME™ ELECTROPLATED FINISH.
|
|
|
|
Hardware Shelf And Support - Pilasters & Standards
|
KNAPE & VOGT® 87/186/187 STANDARDS AND BRACKETS LOCK TOGETHER FOR ADDED SECURITY
|
| 36" Kv87 Anochrome Shelf Standard
...plus other(s)
|
IDEAL FOR WORKSHOPS AND LIGHT INDUSTRIAL APPLICATIONS, KNAPE & VOGT® HEAVY DUTY SHELVING STANDARDS AND BRACKETS COME IN SIZES TO MEET MOST STORAGE REQUIREMENT AND ARE AVAILABLE WITH A WHITE POWDER COAT OR ANOCHROME™ FINISH:
KV87 STANDARDS ARE 12GA STEEL, 7/8" WIDE X 11/16" HIGH AND FEATURE 2" ADJUSTMENT INCREMENTS - 24", 36", 48", 60", 72", 84" AND 96" LENGTHS. KV186LL BRACKETS ARE 12GA STEEL, 4-5/16" HIGH AND WILL ACCOMMODATE SHELF DEPTHS OF 8" AND 10". KV187LL BRACKETS ARE 12GA STEEL, 5-1/16" HIGH FOR SHELF DEPTHS OF 12" 14", 16" AND 18"; 6-1/2" HIGH FOR SHELF DEPTHS OF 20", 22" AND 24". BOTH BRACKET STYLES FEATURE AN INJECTION-MOLDED RESIN LOCKING LEVER TO SECURE THE BRACKETS TO THE STANDARDS.
|
|
|
|
Hardware Shelf And Support - Pilasters & Standards
|
KNAPE & VOGT® 85/185 ANOCHROME™ STANDARDS AND BRACKETS SUPPORT LONG RUNS OF SHELVING
|
| 84" Kv85 Shelf Standard-ano
...plus other(s)
|
FOR USE ANYWHERE STRONG SHELVING IS NEEDED, KNAPE & VOGT® KV85 ANOCHROME™ DOUBLE SLOT SHELVING STANDARDS COME WITH A FINISH THAT RESISTS RUST AND OXIDATION:
DURABLE 16GA STEEL, 1/2"H X 1-1/4"W WITH 1" HEIGHT ADJUSTMENT (#10 FLATHEAD MOUNTING SCREWS NOT INCLUDED). COMPATIBLE WITH KV185 ANOCHROME™ DOUBLE SLOT SHELVING BRACKETS, WHICH SNAP INTO STANDARDS. BRACKETS HAVE HOLES IN CROSS MEMBERS FOR ATTACHING TO SHELF. 8", 10" AND 12" BRACKETS ARE 16GA STEEL; 16" TO 24" ARE 14GA.
|
|
|
|
Hardware Shelf And Support - Pilasters & Standards
|
KNAPE & VOGT® KV71 ANOCHROME™ NARROW FACE SHELVING STANDARDS IDEAL FOR SPECIAL EFFECTS AND CUSTOM FIXTURE DESIGN
|
| 48" Kv71 Shelf Standard
...plus other(s)
|
DESIGNED FOR SPECIALITY APPLICATIONS, KNAPE & VOGT® KV71 ANOCHROME™ NARROW FACE SHELVING STANDARDS COME IN FOUR LENGTHS WITH A FINISH THAT RESISTS RUST AND OXIDATION:
DURABLE 16 GAUGE STEEL, 5/16"W X 13/32"H. 48", 60", 72" AND 96" LENGTHS ( MOUNTING SCREWS NOT INCLUDED).
COMPATIBLE WITH KNAPE & VOGT® KV170 ANOCHROME™ BOLTLESS SHELVING BRACKETS, WHICH FIT AND SNAP INTO STANDARDS: 8", 10", 12", 14" AND 16".
|
|
|
|
Hardware Shelf And Support - Pilasters & Standards
|
KV® 80/180 STANDARDS AND BRACKETS CREATE STRONG, DURABLE SHELVING
|
| 80br 48"brass Pl.standard
...plus other(s)
|
KNAPE & VOGT® KV80 SHELF STANDARDS MEASURE 5/8" WIDE X 13/32" HIGH AND CAN BE MOUNTED ONTO NEARLY ANY TYPE OF WALL:
REINFORCED KV180 SHELF BRACKETS LOCK INTO SLOTTED STANDARDS FOR SECURE, WEIGHT-BEARING SUPPORT. FULLY ADJUSTABLE IN 1" INCREMENTS - BOTH ARE MADE FROM 16GA STEEL. AVAILABLE IN ELECTROPLATED ANOCHROME™ OR BLACK OR WHITE POWDER-COATED FINISHES.
|
|
|
|
Hardware Shelf And Support - Shelf Pins
|
KV® 208 SERIES HEAVY DUTY SHELF BRACKETS 21-1/2"
|
| Hardware For Kv Bracket
...plus other(s)
|
KNAPE & VOGT® SERIES 208™ SHELF BRACKETS ARE MADE FROM 5MM THICK X 1-3/16" WIDE STEEL AND INCLUDE A 3/4" WIDE SWAGED STRUT:
WILL SUPPORT 1,000 LBS. PER PAIR WHEN INSTALLED ACCORDING TO MANUFACTURERS INSTRUCTIONS. FOUR SIZES IN BLACK, WHITE OR TITANIUM TONED EPOXY COATING. BRACKETS SOLD INDIVIDUALLY. OPTIONAL FASTENER PACKAGE INCLUDES THREE, EACH, 5/16" X 3" LAG SCREWS, 5/16" FLAT WASHERS AND #8 X 5/8" WOOD SCREWS."
|
|
|
|
Hardware Shelf And Support - Shelf Pins
|
SPIRAL SUPPORT ADJUSTABLE SHELF PINS
|
| Spiral Support Shelf Pins
...plus other(s)
|
|
INNOVATIVE SHELF PIN DESIGN ALLOWS FINE TUNING OF SHELF INSTALLATIONS.EVEN WITH THE BEST CONSTRUCTION AND INSTALLATION METHODS OFTEN RESULT IN WOBBLY SHELVES. SLIGHTLY WARPED SHELVES AND UNEVEN FLOORS OFTEN LEAD TO SHELVES THAT DON'T SIT FLAT ON THEIR SUPPORTS. PATENT PENDING SPIRAL SUPPORTS™ ARE THE FIRST SHELF PIN THAT PROVIDES ADJUSTABILITY TO ELIMINATE WOBBLE. THE REVOLUTIONARY DESIGN INCORPORATES AN ECCENTRIC CAM THAT CAN BE TURNED WITH A STRAIGHT BLADED SCREWDRIVER TO ALLOW UP TO 2.75MM ( .10") ADJUSTMENT IN SUPPORT HEIGHT. MADE FROM CLEAR PLASTIC, THESE SUPPORTS WILL WORK WITH ANY WOOD TONE OR COLOR CABINETRY. SPIRAL SUPPORTS™ CAN BE USED IN PLACE OF ANY SHELF SUPPORT WITH A 5MM PIN. IMPORTED"
|
|
|
|
Hardware Shelf And Support - Shelf Pins
|
INSTITUTIONAL SHELF SUPPORTS HANDLE 500LB LOADS
|
| Institutional Shelf Support
...plus other(s)
|
TENN-TEX PLASTICS® INTRODUCES ULTRA STRONG POLYCARBONATE SHELF SUPPORTS FOR THICK SHELVES AND HEAVY LOADS:
HIGH CAPACITY SHELF SUPPORTS ARE 1.12" WIDE AND 2.48" LONG, WITH TWO 5MM PINS, SPACED 32MM APART. LOCKING CLIPS HANDLE 3/4" OR 1" THICK SHELVES. COUNTERSUNK HOLES ALLOW WOOD SCREW FASTENING OF CLIPS TO CABINET WALL. CONFORMS TO BHMA /ANSI GRADE 3 REQUIREMENTS AND BHMA STATIC LOAD AND IMPACT LOAD TESTING. TESTED TO 300 LB. SHEAR STRENGTH AND STATIC LOAD TO 525 LB. AVAILABLE IN 100 CT. PACKAGES OR BULK CARTONS OF 1000 PC. MADE IN USA
|
|
|
|
Hardware Shelf And Support - Shelf Pins
|
BRUSSO® 1/4" SOLID BRASS SHELF SUPPORTS
|
| Solid Brass Sleeves For Shelf Pins
...plus other(s)
|
ADDING ELEGANT DETAIL TO BOOKSHELVES AND CABINETS, BRUSSO® 1/4" SOLID BRASS SHELF SUPPORTS AND SLEEVES ARE COMPRISED OF A DECORATIVE TURNED SUPPORT WITH A CYLINDRICAL PEG AND A CYLINDRICAL SLEEVE:
PEG IS 1/4" DIA. X 3/8" LONG; INSTALLED SHELF SUPPORT PROJECTS 7/16". SLEEVES ARE 3/8" OUTSIDE DIAMETER AND REQUIRE A 7/16" DEEP HOLE. USA.
|
|
|
|
Hardware Shelf And Support - Shelf Pins
|
CONCEALED WIRE SHELF SUPPORTS
|
| 7-3/4" "stealth" Shelf Clip
...plus other(s)
|
CONCEALED WIRE SHELF SUPPORTS ARE HIDDEN IN BLIND DADOES ON THE ENDS OF EACH SHELF. NO HARDWARE IS EXPOSED:
TO INSTALL A SHELF USING CONCEALED WIRE SHELF CLIPS FIRST CUT 1/8" WIDE BLIND DADOS AT LEAST 3/8" DEEP INTO EACH SHELF END>/LI>NEXT, DRILL TWO 1/8" DIA. X 3/8" DEEP, PARALLEL HOLES - 7-3/4" OR 9-3/4" ON CENTER - INTO EACH OF THE SIDEWALLS WHERE THE SHELF IS TO BE INSTALLED. PRESS THE CLIP ENDS INTO THE HOLES (INSTALLATION REQUIRES TWO CLIPS PER SHELF), THEN SLIDE THE SHELF OVER AND ONTO THE CLIPS. STEEL CLIPS WORK LIKE SPRINGS IN TENSION TO REMAIN SECURELY IN PLACE. USA."
|
|
|
|
Hardware Shelf And Support - Shelf Pins
|
KNAPE & VOGT® 255 SERIES METAL SHELF STANDARDS AND SUPPORTS IN FINISHES AND SIZES TO MEET ALMOST ANY REQUIREMENT
|
| Zinc Shelf Clip
...plus other(s)
|
KNAPE & VOGT® 255 SERIES METAL SHELF STANDARDS EASILY SURFACE MOUNT OR FIT INTO 5/8"W X 1/4"D DEEP GROOVES:
STRONG ENOUGH TO HOLD WOOD OR LAMINATE SHELVES IN BOOKSHELF AND SHELVING APPLICATIONS (USE RUBBER PAD SUPPORT 866-616 WITH GLASS SHELVES). AVAILABLE IN 24" TO 96" LENGTHS OF ZINC PLATED, BRASS LOOK OR ALMOND, WHITE OR BROWN EPOXY COATED 19 GAUGE STEEL. 17GA. ALUMINUM STANDARDS COME IN 48" TO 144" LENGTHS. MOUNT STANDARDS WITH #4 X 5/8" OR #4 X 3/4" SCREWS (NOT INCLUDED). STANDARDS SOLD INDIVIDUALLY SLOTS ALLOW SHELF SUPPORT ADJUSTMENTS IN 1/2" INCREMENTS - SUPPORTS SOLD IN PACKAGES OF 10, 20 OR 100. USA. TO HELP COMPLETE YOUR PROJECT, MAY WE SUGGEST:
#4 X 3/4" ZINC PLATED SCREWS - 800-523. #4 X 5/8" BRASS PLATED SCREWS - 800-523. #4 X 3/4" ANTIQUE BRASS PLATED SCREWS - 800-514.
|
|
|
|
Hardware Shelf And Support - Shelf Pins
|
5MM SHELF SUPPORTS
|
| Clear 5mm Shelf Supports
...plus other(s)
|
SHELF SUPPORTS FIT INTO 5MM DIA. HOLES:
CHAMFERED ENDS FOR EASY INSERTION. PLASTIC COVERED TO PROTECT FINISHED SHELVES.R FOUR COLORS TO CHOOSE FROM - SOLD IN BAGS OF 100.
|
|
|
|
Hardware Shelf And Support - Shelf Pins
|
METAL AND PLASTIC SHELF SUPPORTS
|
| Brass Support W/1/4" Pin
...plus other(s)
|
METAL AND PLASTIC SHELF SUPPORTS MAKE INSTALLING ADJUSTABLE SHELVING SIMPLE. BORE EQUALLY SPACED HOLES TO MATCH PIN DIAMETER:
PLASTIC SUPPORTS HAVE PINS TO FIT 1/4" DIAMETER HOLES.METAL SUPPORTS ARE OFFERED WITH PINS FOR 1/4" OR 5MM DIAMETER HOLES.LIBRARY STYLE SUPPORTS CAN BE MOUNTED IN 7MM DIAMETER HOLES OR USED WITH BRASS SLEEVES FOR ADDITIONAL LOAD SUPPORT AND A MORE FINISHED APPEARANCE. NYLON SHELF HOLD DOWNS AND PIN AND HOLD DOWN COMBINATIONS FIT 5MM DIAMETER HOLES.OFFERED IN BAGS OF 20, BAGS OF 100 AND SELECTED STYLES ALSO IN 1000 CT BULK PACKAGESPLASTIC SUPPORTS, USAMETAL AND NYLON SUPPORTS, IMPORTED"
|
|
|
|
Hardware Shelf And Support - Shelf Pins
|
LIBRARY STYLE SHELF PINS AND SLEEVES
|
| 10mm Brass Bushing For 6.9mm Pin
...plus other(s)
|
LIBRARY STYLE SHELF PINS AND SLEEVES ENHANCE THE APPEARANCE AND PERFORMANCE OF ADJUSTABLE SHELVES. SOLD SEPARATELY, SO YOU CAN PUT A BUSHING INTO EACH HOLE BUT USE SHELF PINS ONLY WHERE NEEDED:
PRESS-TO-FIT, 9MM AND 10MM OUTSIDE DIA. SMOOTH SHELF BUSHINGS ACCEPT 6.9MM DIA. SMOOTH SHELF PINS. SPOON SHAPED SUPPORTS HAVE AN 11MM WIDE X 13MM LONG SURFACE (7/16" X 9/16") SLEEVES ADD DURABILITY TO WOODEN SURFACES AND DRESS UP THE SHELF PIN HOLES. EXTRA SECURITY FOR SLEEVES CAN BE ACHIEVED BY ADDING A SMALL DROP OF WOOD GLUE WHEN THE SLEEVES ARE INSERTED. SLEEVES AND PINS SOLD IN BAGS OF 10 EACH OR BAGS OF 100 EACH. THESE PINS MUST BE USED WITH SLEEVES. IMPORTED"
|
|
|
|
Hardware Shelf And Support - Shelf Pins
|
MOVING SHELVES IS EASY WITH SPEEDY SHELF SUPPORTS
|
| 18" White Speedy Shelf Support
...plus other(s)
|
WITH SPEEDY SHELF SUPPORTS THERE'S NO NEED TO REPLACE SHELF PINS, COUNT SHELF PIN HOLES OR REMOVE ITEMS WHEN MOVING SHELVES UP. AS A SHELF IS LIFTED, BUILT-IN SPRING-ACTION HOLDERS RETRACT AND THEN SNAP BACK INTO PLACE:
FASTEN 18" LONG, INTERLOCKING SPEEDY SHELF SUPPORTS ONTO LEFT AND RIGHT INNER SIDES OF CABINETS - SURFACE MOUNT OR CUT 5/8" WIDE X 3/8" DEEP DADOES. COUNTERSUNK AND PRE-DRILLED HOLES ALLOW INSTALLATION USING 3/4" STAPLES, 3/4" NAILS OR #4 X 3/4" SCREWS (STAPLES, NAILS OR SCREWS NOT INCLUDED). TO INSTALL A SHELF, REST ONE END ON A PAIR OF SHELF HOLDERS, PUSH IN THE OPPOSITE HOLDERS AND SNAP THE SHELF INTO PLACE. DURABLE WHITE, MEDIUM BROWN OR ALMOND CO-POLYMER SUPPORTS ARE EASILY TRIMMED USING A KNIFE OR SAW. UP TO 400 LBS. LOAD CAPACITY. USA.
|
|
|
|
Hardware Shelf And Support - Shelf Pins
|
LOCKING GLASS SHELF SUPPORTS
|
| 1/4" Glass Clip-chrome
...plus other(s)
|
LOCKING GLASS SHELF CLIPS INCLUDE RUBBER TIPPED NYLON SCREWS TO SECURE GLASS:
BRASS OR CHROME FINISHES PROVIDE A DECORATIVE ACCENT. PLATED STEEL BRACKETS ARE 3/4" SQUARE. 941-602 AND 941-609 HAVE 5MM PINS AND INCLUDE NYLON BUSHINGS SO THEY CAN BE USED AS PIVOT HINGES FOR SMALL GLASS DOORS. NYLON INSERTS ARE NOT DESIGNED FOR USE AS SLEEVES IN SHELF APPLICATIONS.. SOLD IN BAGS OF 4."
|
|
|
|
Hardware Shelf And Support - Shelf Pins
|
SOLID BRASS THREADED LIBRARY SHELF PINS
|
| Threaded Brass Shelf Pins
...plus other(s)
|
SPECIALLY DESIGNED SHELF PINS THREAD INTO EXPANSION BUSHINGS TO LOCK THESE SHELF SUPPORTS IN PLACE:
11/32" DIA. (9MM) X 3/8" DEEP HOLE REQUIRED. BOTH COMPONENTS ARE SOLID BRASS FOR IMPROVED APPEARANCE AND DURABILITY. SOLD IN BAGS OF 10 PINS OR 10 BUSHINGS. NOTE: SHELF PINS MUST ONLY BE USED WITH THESE THREADED BUSHINGS. IMPORTED"
|
|
|
|
Advanced Search Tools
Browse
to see Sub Categories)