|
|
|
3/M™ TRIZACT™ SANDER DISC
|
| 5"x5/16-24 Hookit Ii Backup Pad
...plus other(s)
|
3M™ TRIZACT™ FILM BACKED ABRASIVE CONSISTS OF MICRO-STRUCTURED ALUMINUM OXIDE "PYRAMIDS". WHEN USED, THE TOPS OF THE PYRAMIDS WEAR AWAY, CONTINUALLY EXPOSING FRESH ABRASIVE AND ENSURING A CONSISTENT CUT RATE THROUGHOUT THE LONGER LIFE OF THE PRODUCT:
SAVES TIME - ACHIEVE DESIRED FINISH IN LESS THAN HALF THE TIME OF OTHER METHODS. HIGHER GLOSS LEVEL POSSIBLE - CRISPER REFLECTIONS, RICHER APPEARANCE. LONG ABRASIVE LIFE - LASTS 8 TO 10 TIMES LONGER THAN OTHER ABRASIVES. MORE EFFECTIVE SURFACE LEVELING - FLATTER FINISH, ELIMINATES ORANGE PEEL. ELIMINATES THE NEED FOR COMPOUNDS AND BUFFING. MINIMIZES DUST GENERATION, REQUIRES LITTLE WATER - CAN BE USED ON SITE. SIMPLIFIES SURFACE MAINTENANCE, EASY TOUCH UPS - EVEN ON HIGH GLOSS FINISHES.
APPLICATION SUGGESTIONS:
BEST RESULTS ARE ACHIEVED USING A 10,000 RPM RANDOM ORBITAL SANDER. USE A SPRAY MISTING BOTTLE AS A WATER SOURCE. START AND STOP THE SANDER WHILE RESTING FLAT ON THE SURFACE TO ELIMINATE SWIRL MARKS. RINSE DEBRIS FROM THE WATERPROOF TRIZACT™ DISC AND WIPE SURFACE CLEAN FOLLOWING EACH STEP.
FINISHING STEPS MUST BE FOLLOWED IN SEQUENCE TO ACHIEVE DESIRED FINISH:
OPTIONAL PRE-STEP - 100 MICRON DISC (IF NECESSARY TO LEVEL ROUGH SURFACE AND REMOVE SCRATCHES). MATTE - A35 (MICRON) TRIZACT™ DISC - GREEN. SEMI GLOSS - A10 (MICRON) TRIZACT™ DISC - BLUE. GLOSS - A5 (MICRON) TRIZACT™ DISC - ORANGE. HIGH GLOSS - WHITE CERIUM OXIDE DISC.
CONVERSION DISCS ALLOW YOU TO MODIFY YOUR EXISTING PRESSURE SENSITIVE ADHESIVE (PSA) OR CONVENTIONAL HOOK & LOOP (H&L) BACKUP PAD TO THE PROPRIETARY HOOKIT™ II SYSTEM: 132-395 - 5" PSA TO HOOKIT™ II. 132-401 - 6" PSA TO HOOKIT™ II. 132-398 - 5" H&L TO HOOKIT™ II. 132-404 - 6" H&L TO HOOKIT™ II."
|
|
|
|
Abrasives - Accessories/abrasive Cleaners
|
ABRASIVE CLEANING STICKS
|
| 2"x2"x12" Abrasive Cleaning Stick
...plus other(s)
|
USED LIKE GIANT ERASERS, ABRASIVE CLEANING STICKS REMOVE PITCH AND LOADED DUST FROM SANDING DISCS AND BELTS:
DIFFERENT SIZES AND SHAPES FOR ALL APPLICATIONS. USED LIKE GIANT ERASERS, ABRASIVE CLEANING STICKS REMOVE PITCH AND LOADED DUST FROM SANDING DISCS AND BELTS:
DIFFERENT SIZES AND SHAPES FOR ALL APPLICATIONS. CLEANED BELTS AND DISCS WORK EVEN BETTER AFTER BEING TREATED WITH SOLID BLOCK LUBRICANT.
TO HELP COMPLETE YOUR PROJECT, MAY WE SUGGEST:
MAGLUBE® SOLID BLOCK LUBRICANT - 110-021.
|
|
|
|
Abrasives - Accessories/abrasive Cleaners
|
SOLID SURFACE WORK IS FASTER AND EASIER WITH AN 11" DRIVE PAD ORBITAL SANDER
|
| Acrylic Countertop Sealant 32oz
...plus other(s)
|
THE HEAVY DUTY GEM INDUSTRIES' MODEL BW-H ORBITAL SANDER WEIGHS 16 LBS., BUT FEATURES A WELL BALANCED COUNTERWEIGHT SYSTEM THAT LETS YOU EASILY GUIDE ITS 11" DIA. DRIVE PAD AS IT SANDS WITH A MOTION LIKE THE HUMAN HAND:
110/220V, 2.3A BALL BEARING, CAPACITOR MOTOR - 1,700 ORBITS PER MINUTE GREATLY MINIMIZE POSSIBILITY OF SWIRL MARKS ASSOCIATED WITH HIGH-SPEED ROTARY BUFFERS. NO GEARS TO GRIND OR STRIP. NO ARMATURE WINDING TO BURN OUT. NO CARBON BRUSHES TO BURN OUT. HEAVY DUTY ALUMINUM HOUSING - WORKS EQUALLY WELL AND UNIFORMLY ON SOLID SURFACE AND WOOD PRODUCTS. INCLUDES MODEL C-515C DRIVE PAD WITH PAN AND HOOKIT™ II MOUNTING SYSTEM (ORDER SANDING DISCS OR PADS, SEPARATELY). SANDING DISCS OR PADS AVAILABLE IN SCOTCH-BRITE®, ALUMINUM OXIDE OR TRIZACT™ STRUCTURED ABRASIVES. MICRON GRADE VS. U.S. MESH GRADE: 30 = 400, 60 = 220, 80 = 180, 100 = 150, 180 = 80.
123-665 - MODEL C-515HD HEAVY DUTY DRIVE PAD FEATURES LAYER OF RUBBER FOR MORE AGGRESSIVE WORK - LASTS UP TO 5 TIMES LONGER AND HOLDS UP BETTER IN DAMP APPLICATIONS. 123-662 - MODEL S-112 SHROUD ELIMINATES MUCH OF THE DUST ASSOCIATED WITH SANDING OPERATIONS - 1-1/2" DIA. OUTLET INCLUDES ADAPTOR TO FIT 1-1/4" DIA. SHOP VACUUM HOSE. 123-671 - MODEL C-645S SOLID SURFACE COMPOUND PREPARES SURFACE FOR UNIFORM BONDING WITH ACRYLIC AND IS A REQUIRED FIRST STEP BEFORE APPLYING SEALANT - ONCE SANDING AND FINISHING ARE COMPLETE, APPLY COMPOUND WITH POLISHER/SANDER AND MICRO-FIBER BONNET. 123-668 - MODEL C-523S COUNTERTOP SEALANT SEALS SURFACE WITH A LAYER OF ACRYLIC, PROTECTS AGAINST SCRATCHES AND STAINS AND ELIMINATES MOST MAINTENANCE PROBLEMS ON SEMI-GLOSS AND HIGH GLOSS SURFACES.
|
|
|
|
Abrasives - Accessories/abrasive Cleaners
|
ABRASIVE CLEANING STICKS GET EXTRA MILEAGE OUT OF LOADED SANDING BELTS AND DISCS
|
| 3"x3"x12" Abrasive Cleaning Stick
...plus other(s)
|
USED LIKE GIANT ERASERS, ABRASIVE CLEANING STICKS REMOVE PITCH AND LOADED DUST FROM SANDING DISCS AND BELTS:
DIFFERENT SIZES AND SHAPES FOR ALL APPLICATIONS. CLEANED BELTS AND DISCS WORK EVEN BETTER AFTER BEING TREATED WITH SOLID BLOCK LUBRICANT.
TO HELP COMPLETE YOUR PROJECT, MAY WE SUGGEST:
MAGLUBE® SOLID BLOCK LUBRICANT - 110-021.
|
|
|
|
Abrasives - Accessories/hand Sanding
|
PREPPIN' WEAPON SANDING BLOCK
|
| Preppin Weapon Sanding Block
|
THE PREPPIN' WEAPON SANDING BLOCK LETS YOU LOAD UP TO FOUR SHEETS OF SANDPAPER AT ONE TIME AND THEN TEAR OFF EACH SHEET AS IT WEARS OUT:
USES 1/4 SHEETS CUT FROM 9" X 11" SANDPAPER. THE PREPPIN' WEAPON SANDING BLOCK LETS YOU LOAD UP TO FOUR SHEETS OF SANDPAPER AT ONE TIME AND THEN TEAR OFF EACH SHEET AS IT WEARS OUT:
USES 1/4 SHEETS CUT FROM 9" X 11" SANDPAPER. EASY TO USE LEVER ACTION CLIPS MAKE RELOADING A SNAP. HIGH IMPACT ABS PLASTIC BODY. POLISHED STAINLESS STEEL CLIPS WON'T RUST, PERMITTING DRY OR WET SANDING - STYROFOAM CORE MEANS BLOCK WILL FLOAT. TAPERED EDGES ALLOW SANDING INTO CORNERS. COMFORTABLE GRIP REDUCES FATIGURE DURING EXTENDED PERIODS OF WORK. 7-3/4"L X 2-3/4"W, WEIGHS 1 LB. USA.
|
|
|
|
Abrasives - Accessories/hand Sanding
|
ROUND RUBBER HAND SANDER
|
| 5" Psa Round Rubber Hand Sander
...plus other(s)
|
USING THE SAME 5" OR 6" DIA. HOOK & LOOP (H&L) OR PRESSURE SENSITIVE ADHESIVE (PSA) DISC SANDPAPER AS YOUR POWERED SANDER, A ROUND RUBBER HAND SANDER WORKS GREAT WITH FINE GRIT TO GET OUT THE FINAL SWIRL MARKS LEFT BY A RANDOM ORBIT SANDER:
EASY GRIP HANDLE FOR QUICK AND EFFICIENT HAND SANDING. ALTHOUGH ROUND AND FLAT, SANDER WILL STILL ROLL UP ONTO A BACK SPLASH OR GENTLE CONTOUR, WHEN NEEDED."
|
|
|
|
Abrasives - Accessories/hand Sanding
|
ROUND RUBBER HAND SANDER
|
| 6" Psa Round Rubber Hand Sander
...plus other(s)
|
USING THE SAME 5" OR 6" DIA. HOOK & LOOP (H&L) OR PRESSURE SENSITIVE ADHESIVE (PSA) DISC SANDPAPER AS YOUR POWERED SANDER, A ROUND RUBBER HAND SANDER WORKS GREAT WITH FINE GRIT TO GET OUT THE FINAL SWIRL MARKS LEFT BY A RANDOM ORBIT SANDER USING THE SAME 5" OR 6" DIA. HOOK & LOOP (H&L) OR PRESSURE SENSITIVE ADHESIVE (PSA) DISC SANDPAPER AS YOUR POWERED SANDER, A ROUND RUBBER HAND SANDER WORKS GREAT WITH FINE GRIT TO GET OUT THE FINAL SWIRL MARKS LEFT BY A RANDOM ORBIT SANDER:
EASY GRIP HANDLE FOR QUICK AND EFFICIENT HAND SANDING. ALTHOUGH ROUND AND FLAT, SANDER WILL STILL ROLL UP ONTO A BACK SPLASH OR GENTLE CONTOUR, WHEN NEEDED.
|
|
|
|
Abrasives - Accessories/hand Sanding
|
QUICK CHANGE SANDING BLOCK
|
| 3"x21" Blockw/2ea 60,80,100,120,150
...plus other(s)
|
MADE FROM THERMOPLASTIC RUBBER, THIS VERSATILE, SPRING-LOADED SANDING BLOCK USES 3" X 21" SANDING BELTS AND IS DESIGNED TO MAKE IT EASIER THAN EVER TO ADVANCE THE BELT TO A CLEAN AND UNUSED SECTION MADE FROM THERMOPLASTIC RUBBER, THIS VERSATILE, SPRING-LOADED SANDING BLOCK USES 3" X 21" SANDING BELTS AND IS DESIGNED TO MAKE IT EASIER THAN EVER TO ADVANCE THE BELT TO A CLEAN AND UNUSED SECTION:
LIFT THE LEVER AND A WORN BELT CAN BE EASILY ROTATED TO AN UNUSED SEGMENT OR REPLACED. PUSH THE LEVER DOWN AND THE SANDING BELT IS LOCKED AND LOADED, READY FOR USE. THE ROUNDED NOSE SANDS INTO RELATIVELY TIGHT SPACES. INCLUDES 10 SANDING BELTS - 60, 80, 100, 120, 150 GRIT (TWO EACH). USA.
|
|
|
|
Abrasives - Accessories/hand Sanding
|
THINNER, FLEXIBLE SANDING SPONGES HANDLE FINE WORK WITH EASE
|
| Soft Sand Sponge-coarse
...plus other(s)
|
MOST WOODWORKERS USE THICK, ABRASIVE FOAM SPONGES, BUT WE ALL KNOW HOW AWKWARD THEY CAN BE, ESPECIALLY FOR FINE WORK:
THESE THINNER, FLEXIBLE SANDING SPONGES ARE VERY FLEXIBLE, CAN BE USED WET OR DRY, AND RINSE CLEAN WITH WATER. DEFINITELY THE BEST OF THE LATEST INNOVATIONS IN FLEXIBLE SANDING.
LIMITED TO QUANTITIES ON HAND
|
|
|
|
Abrasives - Accessories/hand Sanding
|
A&H ABRASIVES SANDING SPONGES
|
| 3"x4" Sand Sponge Coarse (60 Grit)
...plus other(s)
|
BUY IN BULK AND SAVE 3" X 4" SANDING SPONGES 144 TO THE CASE. BUY IN BULK AND SAVE 3" X 4" SANDING SPONGES 144 TO THE CASE. COME IN FOUR DIFFERENT GRITS:
COARSE (60 GRIT), MEDIUM (80 GRIT), FINE (100 GRIT), EXTRA FINE (150 GRIT). 1/2" THICK FOAM PADS ARE REINFORCED WITH FABRIC FOR LONGER LIFE. CONFORMS TO SHAPES BETTER THAN CONVENTIONAL SANDPAPER AND LAST UP TO 10 TIMES LONGER. CAN BE USED WER OR DRY. GRIT IS ON ONE SIDE ONLY.
|
|
|
|
Abrasives - Accessories/hand Sanding
|
5" AND 6" FLEX HAND SANDING PADS
|
| 5" H&l Flex Pad, 1/8" Thick
...plus other(s)
|
FLEX HAND SANDING PADS ARE GREAT FOR CONTOUR SANDING ON FURNITURE, WOODTURNINGS AND WHEREVER CURVED AND IRREGULAR SHAPES ARE HARD TO SAND. THESE H&L SPONGE PADS SAVE YOUR FINGERPRINTS WHILE ENSURING CONSISTENT SURFACES AND LONGER LASTING SANDPAPER:
ELASTIC STRAP SECURELY HOLDS PAD TO HAND. CAN BE USED WITH ANY H&L SANDPAPER AND ABRASIVE PADS. USE 1/8" PAD FOR TIGHTER CURVES AND SMALL DIAMETER SPINDLES. USE 3/8" PAD FOR LARGER CURVES, BOWLS AND FLAT SANDING OPERATIONS. INTERFACE PADS ADD ADDITIONAL CUSHIONING AND FLEXIBILITY.
TO HELP COMPLETE YOUR PROJECT, MAY WE SUGGEST:
C-WEIGHT H&L PAPER BACKED DISCS - 132-674. F-WEIGHT H&L CLOTH BACKED DISCS - 949-846. J-WEIGHT H&L CLOTH BACKED DISCS - 131-387. NYLON H&L ABRASIVE PADS - 912-776. MICRO H&L SANDING DISCS - 949-373. MICRO-MESH H&L SANDING DISCS - 125-315. ABRALON H&L SANDING PADS - 928-165. LAMBS WOOL H&L BUFFING PADS - 143-186.
|
|
|
|
Abrasives - Accessories/hand Sanding
|
HAND SANDING BLOCKS FOR ALMOST EVERY IMAGINABLE SHAPE
|
| Curv-a-flex
...plus other(s)
|
CURVED PIECES, TIGHT CORNERS, NOOKS AND CRANNIES ARE ALL EASIER TO SAND WITH THESE COMFORTABLE, PREMOLDED OR MEDIUM DENSITY RUBBER HAND SANDING BLOCKS:
920-555 - CURV-A-FLEX™ CAN BE ROLLED TIGHTER OR LOOSER TO MATCH ANY RADIUS YOU NEED TO SAND. 5-1/2"L X 2-1/8" OD RADIUS CURVE - PREMOLDED RUBBER. 920-565 - 5" TRUE FLAT PUTS A LOT OF PAPER IN CONTACT WITH THE WOOD TO SPEED PANEL SANDING. 2-3/4"W X 5"L - MEDIUM DENSITY RUBBER. 920-569 - 9" TRUE FLAT IS SIMILAR TO 5" TRUE FLAT BUT IS 9"L. 920-576 - LARGE TEARDROP™ HAS SHARP POINTS AND EDGES THAT ARE GREAT FOR SANDING GLUE FROM CORNERS, WHILE THE SMOOTH RADIUS MAKES IT USEFUL FOR CURVED PIECES. SPLIT DESIGN LOCKS ABRASIVE PAPER IN PLACE. 5-1/2"L X 1-5/8" OD RADIUS CURVE - PREMOLDED RUBBER. 920-583 - SMALL TEARDROP™ IS SIMILAR TO LARGE TEARDROP BUT IS 2-1/2"L. 920-590 - DOUBLE DENSITY BLOCKS HAVE A FIRM SIDE FOR SANDING PANELS AND A SOFTER SIDE FOR CONTOURS. "H X "W X "L - SOFT RUBBER, CAN BE USED FOR WET OR DRY SANDING. 920-592 - BUY ALL SIX SANDING BLOCKS AT ONE TIME AND SAVE ON PRICE AND SHIPPING! SANDING BLOCKS CAN USE 1/4 AND 1/2 SHEET OR ROLL STOCK ABRASIVES (NOT INCLUDED).
TO HELP COMPLETE YOUR PROJECT, MAY WE SUGGEST:
111-122 - 9" X 11" ALUMINUM OXIDE SANDPAPER SHEETS.
|
|
|
|
Abrasives - Accessories/hand Sanding
|
HAND SANDING BLOCKS
|
| 5" True Flat Sander
...plus other(s)
|
CURVED PIECES, TIGHT CORNERS, NOOKS AND CRANNIES ARE ALL EASIER TO SAND WITH THESE COMFORTABLE, PREMOLDED OR MEDIUM DENSITY RUBBER HAND SANDING BLOCKS CURVED PIECES, TIGHT CORNERS, NOOKS AND CRANNIES ARE ALL EASIER TO SAND WITH THESE COMFORTABLE, PREMOLDED OR MEDIUM DENSITY RUBBER HAND SANDING BLOCKS:
920-555 - CURV-A-FLEX™ CAN BE ROLLED TIGHTER OR LOOSER TO MATCH ANY RADIUS YOU NEED TO SAND. 5-1/2"L X 2-1/8" OD RADIUS CURVE - PREMOLDED RUBBER. 920-565 - 5" TRUE FLAT PUTS A LOT OF PAPER IN CONTACT WITH THE WOOD TO SPEED PANEL SANDING. 2-3/4"W X 5"L - MEDIUM DENSITY RUBBER. 920-569 - 9" TRUE FLAT IS SIMILAR TO 5" TRUE FLAT BUT IS 9"L. 920-576 - LARGE TEARDROP™ HAS SHARP POINTS AND EDGES THAT ARE GREAT FOR SANDING GLUE FROM CORNERS, WHILE THE SMOOTH RADIUS MAKES IT USEFUL FOR CURVED PIECES. SPLIT DESIGN LOCKS ABRASIVE PAPER IN PLACE. 5-1/2"L X 1-5/8" OD RADIUS CURVE - PREMOLDED RUBBER. 920-583 - SMALL TEARDROP™ IS SIMILAR TO LARGE TEARDROP BUT IS 2-1/2"L. 920-590 - DOUBLE DENSITY BLOCKS HAVE A FIRM SIDE FOR SANDING PANELS AND A SOFTER SIDE FOR CONTOURS. "H X "W X "L - SOFT RUBBER, CAN BE USED FOR WET OR DRY SANDING. 920-592 - BUY ALL SIX SANDING BLOCKS AT ONE TIME AND SAVE ON PRICE AND SHIPPING! SANDING BLOCKS CAN USE 1/4 AND 1/2 SHEET OR ROLL STOCK ABRASIVES (NOT INCLUDED).
TO HELP COMPLETE YOUR PROJECT, MAY WE SUGGEST:
111-122 - 9" X 11" ALUMINUM OXIDE SANDPAPER SHEETS.
|
|
|
|
Abrasives - Accessories/hand Sanding
|
ABRASIVE SPONGE
|
| Laquer Sanding Pad
|
|
DESIGNED SPECIFICALLY FOR LEVELING FINISHES BETWEEN COATS, THE LACQUER SANDING PAD IS A FOAM PAD WITH ABRASIVES BONDED RIGHT TO IT. DESIGNED SPECIFICALLY FOR LEVELING FINISHES BETWEEN COATS, THE LACQUER SANDING PAD IS A FOAM PAD WITH ABRASIVES BONDED RIGHT TO IT. THE LACQUER SANDING PAD IS A FOAM PAD WITH 80 GRIT ALUMINUM OXIDE ABRASIVES BONDED RIGHT TO IT. THE CUSHIONING SPREADS OUT THE SANDING PREASURE EVENLY SO THEY WON'T BURN THROUGH THE FINISH. IT PRODUCES AN EVEN, DULL SHEEN SO IT'S EASIER TO KNOW WHEN THE FINISH IS LEVEL. THESE ARE LONG LASTING PADS THAT RESIST LOADING, JUST KNOCK THE PAD CLEAN AND KEEP ON SANDING. THE SINGLE SIDED, 3" X 5" X 1/2" PAD IS EFFECTIVE ON WATER BASED FINISHES AS WELL.
|
|
|
|
Abrasives - Accessories/hand Sanding
|
A&H ABRASIVES™ SANDING SPONGES
|
| Sanding Sponge Coarse Block
...plus other(s)
|
SOFT FOAM WITH AN ALUMINUM OXIDE ABRASIVE COATING, SANDING SPONGES COME IN FIVE DIFFERENT SHAPES AND FOUR GRITS:
SHAPES INCLUDE BLOCK, ROUND, COMBO, DOUBLE SLANT AND SLANT; APPROXIMATELY 2-3/4" X 4" X 1". 80-120 GRIT COARSE, 120-180 GRIT MEDIUM, 220-280 GRIT FINE, 400-600 GRIT SUPER FINE. SOLD IN BAGS OF 10. BLOCK SANDING KIT INCLUDES TWO, EACH, COARSE, MEDIUM, FINE AND SUPER FINE SPONGES. MEDIUM GRIT COMBO KIT COMES WITH TWO, EACH, BLOCK, ROUND, COMBO, DOUBLE SLANT AND SLANT SPONGES. FINE GRIT COMBO KIT CONTAINS THE SAME SHAPES AS THE MEDIUM GRIT KIT. USA."
|
|
|
|
Abrasives - Accessories/hand Sanding
|
A&H ABRASIVESTM SANDING SPONGES
|
| Block Sanding Sponge Kit
...plus other(s)
|
SOFT FOAM WITH AN ALUMINUM OXIDE ABRASIVE COATING, SANDING SPONGES COME IN FIVE DIFFERENT SHAPES AND FOUR GRITS SOFT FOAM WITH AN ALUMINUM OXIDE ABRASIVE COATING, SANDING SPONGES COME IN FIVE DIFFERENT SHAPES AND FOUR GRITS:
SHAPES INCLUDE BLOCK, ROUND, COMBO, DOUBLE SLANT AND SLANT; APPROXIMATELY 2-3/4" X 4" X 1". 80-120 GRIT COARSE, 120-180 GRIT MEDIUM, 220-280 GRIT FINE, 400-600 GRIT SUPER FINE. SOLD IN BAGS OF 10. BLOCK SANDING KIT INCLUDES TWO, EACH, COARSE, MEDIUM, FINE AND SUPER FINE SPONGES. MEDIUM GRIT COMBO KIT COMES WITH TWO, EACH, BLOCK, ROUND, COMBO, DOUBLE SLANT AND SLANT SPONGES. FINE GRIT COMBO KIT CONTAINS THE SAME SHAPES AS THE MEDIUM GRIT KIT. USA.
|
|
|
|
Abrasives - Accessories/hand Sanding
|
A&H ABRASIVESTM ABRASIVE FINISHING SPONGES
|
| Soft Hand Pad-medium
...plus other(s)
|
DURING THE WET SANDING PROCESS, ABRASIVE FINISHING SPONGES HEAT DANISH OIL APPLIED TO THE WOOD'S SURFACE, TURNING IT INTO A "GRAVY" THAT SOAKS IN, FILLS THE GRAIN AND LEAVES A BEAUTIFUL SHEEN DURING THE WET SANDING PROCESS, ABRASIVE FINISHING SPONGES HEAT DANISH OIL APPLIED TO THE WOOD'S SURFACE, TURNING IT INTO A "GRAVY" THAT SOAKS IN, FILLS THE GRAIN AND LEAVES A BEAUTIFUL SHEEN:
SOLD IN PACKAGES OF 10 AND AVAILABLE IN FIVE GRITS TO MEET YOUR SPECIFIC REQUIREMENTS: COARSE (36-80); MEDIUM (80-120); FINE (120-180); VERY FINE (180-220); AND SUPER FINE (220-400). 1/2" X 3-3/4" X 4-3/4". CLEAN WITH MINERAL SPIRITS TO REUSE.
TO HELP COMPLETE YOUR PROJECT, MAY WE SUGGEST:
J.E. MOSER'S® DANISH OIL - 859-973.
|
|
|
|
Abrasives - Accessories/hand Sanding
|
A&H ABRASIVES™ FLEXIBLE SANDING SPONGES
|
| Thin Sanding Sponge-medium
...plus other(s)
|
THICK, ABRASIVE FOAM SPONGES CAN SOMETIMES BE AWKWARD TO USE FOR FINE WORK. THESE THINNER, FLEXIBLE SANDING SPONGES SOLVE THAT PROBLEM:
SPONGES ARE VERY FLEXIBLE AND CAN BE USED WET OR DRY - RINSE CLEAN WITH WATER. DEFINITELY THE BEST OF THE LATEST INNOVATIONS IN FLEXIBLE SANDING. SEVEN GRITS TO CHOOSE FROM - MEDIUM (120-180), FINE (220-280), VERY FINE (280-400), SUPER FINE (400-600), SUPER FINE+ (600-800), MICRO FINE (800-1200) AND MICRO FINE+ (1500-2000). SOLD IN PACKAGES OF 5. COMBO SET INCLUDES 14 SPONGES (TWO OF EACH GRIT)."
|
|
|
|
Abrasives - Accessories/hand Sanding
|
A&H ABRASIVESTM FLEXIBLE SANDING SPONGES
|
| Thin Sponge Assortment 2ea. Grit
...plus other(s)
|
THICK, ABRASIVE FOAM SPONGES CAN SOMETIMES BE AWKWARD TO USE FOR FINE WORK. THESE THINNER, FLEXIBLE SANDING SPONGES SOLVE THAT PROBLEM. THICK, ABRASIVE FOAM SPONGES CAN SOMETIMES BE AWKWARD TO USE FOR FINE WORK. THESE THINNER, FLEXIBLE SANDING SPONGES SOLVE THAT PROBLEM:
SPONGES ARE VERY FLEXIBLE AND CAN BE USED WET OR DRY - RINSE CLEAN WITH WATER. DEFINITELY THE BEST OF THE LATEST INNOVATIONS IN FLEXIBLE SANDING. SEVEN GRITS TO CHOOSE FROM - MEDIUM (120-180), FINE (220-280), VERY FINE (280-400), SUPER FINE (400-600), SUPER FINE+ (600-800), MICRO FINE (800-1200) AND MICRO FINE+ (1500-2000). SOLD IN PACKAGES OF 5. COMBO SET INCLUDES 14 SPONGES (TWO OF EACH GRIT).
|
|
|
|
Abrasives - Accessories/lubricants
|
ABRASIVE BELT LUBRICANT
|
| 3.2 Oz Mag Lub Abrasive Lubricant
...plus other(s)
|
MAGLUBE® SOLID BLOCK LUBRICANT REALLY WORKS AND IS COMPLETELY BIODEGRADABLE, SAFE AND CAN DOUBLE THE LIFE OF ABRASIVE BELTS OR DISCS MAGLUBE® SOLID BLOCK LUBRICANT REALLY WORKS AND IS COMPLETELY BIODEGRADABLE, SAFE AND CAN DOUBLE THE LIFE OF ABRASIVE BELTS OR DISCS:
KEEPS SANDPAPER CLEAN AND SHARP LONGER - WON'T SPOT OR STAIN WOOD. GENTLY RUB ON FOR IMMEDIATE RESULTS. 1-3/8"H X 2-3/4"W X 1-13/16"D BLOCK; 2" DIA. X 9" TUBE. BEST RESULTS ARE ACHIEVED WHEN USED IN COMBINATION WITH AN ABRASIVE CLEANING STICK. USA.
TO HELP COMPLETE YOUR PROJECT, MAY WE SUGGEST:
ABRASIVE CLEANING STICKS - 111-001.
|
|
|
|
Abrasives - Accessories/lubricants
|
ABRASIVE BELT GREASE STICKS
|
| Abrasive Belt Grease Stick F-26
...plus other(s)
|
USE FORMAX ABRASIVE BELT GREASE STICKS ON BELTS AND DISCS TO PREVENT LOADING AND GLAZING AS WELL AS TO HELP THEM CUT COOLER WITH COATED ABRASIVE PRODUCTS USE FORMAX ABRASIVE BELT GREASE STICKS ON BELTS AND DISCS TO PREVENT LOADING AND GLAZING AS WELL AS TO HELP THEM CUT COOLER WITH COATED ABRASIVE PRODUCTS:
F-26 SPREADS OUT THINLY AND REMAINS WET ON THE BELT. IT PROVIDES LUBRICATION BY PENETRATING THE COATED ABRASIVE SURFACE - RECOMMENDED FOR ALL BELT AND DISC POLISHING OPERATIONS INVOLVING METALS, PLASTIC AND GLASS. F-115 IS A COMBINATION OF BELT GREASE AND TRIPOLI ABRASIVE - RECOMMENDED FOR BELT POLISHING NON-FERROUS METALS. A COMBINATION OF BELT GREASE AND SOFT ALUMINUM OXIDE, F-122 IS RECOMMENDED FOR BELT POLISHING ALL TYPES OF STEEL. USA.
|
|
|
|
Abrasives - Accessories/lubricants
|
3" X 6" GRAPHITE SANDER PLATENS
|
| 5" Wide Graphite Canvas
...plus other(s)
|
AN EASY-TO-INSTALL ACCESSORY THAT HELPS REDUCE FRICTION AND HEAT BUILD-UP, WITH A&H ABRASIVES™ GRAPHITE-COATED PLATENS YOU CAN PUT MORE PRESSURE ONTO YOUR SANDER AND STILL MAINTAIN BELT SPEED:
SOLD IN PACKAGES OF THREE; PRESSURE SENSITIVE ADHESIVE (PSA) BACKED PLATENS ADHERE TO YOUR SANDER'S METAL BASEPLATE. 3" X 6" FITS 3" X 21" BELT SANDERS. 4" X 6" IS FOR 4" X 24" BELT SANDERS. 4-1/2" X 12-1/2" FITS 4" X 36" SANDERS. 6" X 18" IS FOR 6" X 48" BELT SANDER/CUSTOM APPLICATIONSS. AVAILABLE BY THE YARD, 4", 5" OR 6" WIDE GRAPHITE-COATED CANVAS COMES IN CONTINUOUS ROLLS FOR CUSTOM APPLICATIONS. SOLD WITHOUT PSA BACKING (APPLY SPRAY ADHESIVE FOR A SOLID BOND). USA.
TO HELP COMPLETE YOUR PURCHASE, MAY WE SUGGEST:
3M™ REPOSITIONABLE 75 SPRAY ADHESIVE - 100-169.
|
|
|
|
Abrasives - Accessories/lubricants
|
A&H ABRASIVES™ GRAPHITE PLATENS AND ROLLS
|
| 4" Wide Graphite Canvas
...plus other(s)
|
AN EASY-TO-INSTALL ACCESSORY THAT HELPS REDUCE FRICTION AND HEAT BUILD-UP, WITH A&H ABRASIVES™ GRAPHITE-COATED PLATENS YOU CAN PUT MORE PRESSURE ONTO YOUR SANDER AND STILL MAINTAIN BELT SPEED:
PRICED PER YARD, 4", 5" OR 6" WIDE GRAPHITE-COATED CANVAS COMES IN CONTINUOUS ROLLS FOR CUSTOM APPLICATIONS. SOLD WITHOUT PSA BACKING (APPLY SPRAY ADHESIVE FOR A SOLID BOND). SOLD IN PACKAGES OF THREE; PRESSURE SENSITIVE ADHESIVE (PSA) BACKED PLATENS ADHERE TO YOUR SANDER'S METAL BASEPLATE. 3" X 6" FITS 3" X 21" BELT SANDERS. 4" X 6" IS FOR 4" X 24" BELT SANDERS. 6" X 18" IS FOR 6" X 48" BELT SANDER/CUSTOM APPLICATIONS. USA.
TO HELP COMPLETE YOUR PURCHASE, MAY WE SUGGEST:
3M™ REPOSITIONABLE 75 SPRAY ADHESIVE - 100-169."
|
|
|
|
Abrasives - Accessories/lubricants
|
A&H ABRASIVESTM GRAPHITE PLATENS AND ROLLS
|
| 6" Wide Graphite Canvas
...plus other(s)
|
AN EASY-TO-INSTALL ACCESSORY THAT HELPS REDUCE FRICTION AND HEAT BUILD-UP, WITH A&H ABRASIVES™ GRAPHITE-COATED PLATENS YOU CAN PUT MORE PRESSURE ONTO YOUR SANDER AND STILL MAINTAIN BELT SPEED AN EASY-TO-INSTALL ACCESSORY THAT HELPS REDUCE FRICTION AND HEAT BUILD-UP, WITH A&H ABRASIVES™ GRAPHITE-COATED PLATENS YOU CAN PUT MORE PRESSURE ONTO YOUR SANDER AND STILL MAINTAIN BELT SPEED:
PRICED PER YARD, 4", 5" OR 6" WIDE GRAPHITE-COATED CANVAS COMES IN CONTINUOUS ROLLS FOR CUSTOM APPLICATIONS. SOLD WITHOUT PSA BACKING (APPLY SPRAY ADHESIVE FOR A SOLID BOND). SOLD IN PACKAGES OF THREE; PRESSURE SENSITIVE ADHESIVE (PSA) BACKED PLATENS ADHERE TO YOUR SANDER'S METAL BASEPLATE. 3" X 6" FITS 3" X 21" BELT SANDERS. 4" X 6" IS FOR 4" X 24" BELT SANDERS. 6" X 18" IS FOR 6" X 48" BELT SANDER/CUSTOM APPLICATIONS. USA.
TO HELP COMPLETE YOUR PURCHASE, MAY WE SUGGEST:
3M™ REPOSITIONABLE 75 SPRAY ADHESIVE - 100-169.
|
|
|
|
Abrasives - Accessories/other
|
MITCHELL'S SANDING CORD AND TAPE
|
| .055"x50ft Abrasive Cord Roll
...plus other(s)
|
HANDY 50 FOOT SPOOLS OF 150-GRIT ALUMINUM OXIDE ABRASIVE TAPE OR CORD MAKE IT POSSIBLE TO SAND THOSE "NEAR TO IMPOSSIBLE PLACES" WITH EASE:
EXCELLENT FOR SANDING HOLES, INSIDE DIAMETERS, TURNINGS AND IRREGULAR SHAPES HANDY 50 FOOT SPOOLS OF 150-GRIT ALUMINUM OXIDE ABRASIVE TAPE OR CORD MAKE IT POSSIBLE TO SAND THOSE "NEAR TO IMPOSSIBLE PLACES" WITH EASE:
EXCELLENT FOR SANDING HOLES, INSIDE DIAMETERS, TURNINGS AND IRREGULAR SHAPES. ESPECIALLY USEFUL FOR LATHE, CARVING OR REFINISHING WORK. 0.005" DIA. CORD; 3/16" WIDE TAPE. ALSO USEFUL FOR AUTO BODY REPAIRS, PLUMBING AND METAL WORKING. A MUST FOR EVERY TOOL KIT!
|
|
|
|
Abrasives - Accessories/other
|
ALUMINUM OXIDE TYPE 1 CUT OFF WHEEL
|
| 1/4" & 3/8" 3 Pc Mandrel Set
...plus other(s)
|
SAIT TYPE 1 CUT OFF WHEELS ARE FAST CUTTING AND EXTREMELY LONG LASTING FOR TOUGH APPLICATIONS:
SEVEN SIZES AND THREE TYPES OF ALUMINUM OXIDE GRIT TO SELECT FROM: A24R - MEDIUM BOND, GENERAL PURPOSE - IRON, STEEL, WELDS, ETC. A36T - HARD BOND, AGGRESSIVE CUTTING - IRON, STEEL, WELDS, STAINLESS STEEL. A60S - HARD BOND, EXTREMELY FAST - IRON, STEEL, WELDS, ETC. NOTE: CUT SPEED IS MAXIMUM RECOMMENDED RPM. USA. OPTIONAL WHEEL ADAPTERS AND MANDREL SET ALLOW YOU TO ACCOMMODATE DIFFERING BORE DIAMETERS - 1/4" SHANKS."
|
|
|
|
Abrasives - Accessories/other
|
FEATHERING DISC ADHESIVE
|
| Feathering Disc Adhes 50z Tube
|
A TRANSPARENT, FAST-DRYING ADHESIVE FOR ADHERING PAPER- OR CLOTH-BACKED ABRASIVE DISCS TO CLOTH, SPONGE RUBBER, METAL, PLASTIC OR OTHER BACK-UP PLATES, A TRANSPARENT, FAST-DRYING ADHESIVE FOR ADHERING PAPER- OR CLOTH-BACKED ABRASIVE DISCS TO CLOTH, SPONGE RUBBER, METAL, PLASTIC OR OTHER BACK-UP PLATES, 3M™ FEATHERING DISC ADHESIVE (TYPE II) IS SPECIALLY FORMULATED TO ALLOW MULTIPLE APPLICATIONS WITHOUT ADHESIVE BUILDUP OR PAPER DELAMINATION:
DESIGNED FOR USE WITH A-WEIGHT ABRASIVE DISCS. SOLD IN 5 OZ. TUBES. NOTE: GROUND SHIPMENT ONLY.
|
|
|
|
Abrasives - Accessories/other
|
A&H ABRASIVES™ ALUMINUM OXIDE AND ZIRCONIA ALUMINA MINI FLAP DISC
|
| 3"x1/4" Type R Mandrel
...plus other(s)
|
THEIR COMPACT SIZE MAKES IT EASY TO USE MINI FLAPDISCS TO GRIND IN THOSE HARD-TO-REACH PLACES. MINI FLEXIDISCS ARE CONSTRUCTED WITH OVERLAPPING FLAPS OF ABRASIVE CLOTH AT A STEEPER PITCH, ALLOWING THE DISCS TO BE MORE FLEXIBLE FOR ROUNDING OR CONTOUR SANDING:
ALUMINUM OXIDE OR ZIRCONIA ALUMINA GRIT. EACH USES TYPE R SCREW-ON FASTENING SYSTEM FOR SECURE AND QUICK CHANGING.
|
|
|
|
Abrasives - Accessories/other
|
HOOK AND LOOP SANDING DISC HOLDERS
|
| 3" Soft H&l Disc Holder
...plus other(s)
|
MOSTLY USED BY BOWL TURNERS, HOOK & LOOP SANDING DISC HOLDERS ARE AVAILABLE IN THREE SIZES IN BOTH SOFT OR FIRM DENSITY:
DISK HOLDERS HAVE 1/4" ROUND SHANKS. H&L BUFFING PADS USED FOR FINAL PASTE WAX BUFFING. USA.
TO HELP COMPLETE YOUR PURCHASE, MAY WE SUGGEST:
2", 3" AND 5" ROUND PAPER BACKED A/O H&L SANDING DISCS - 133-754. 2", 3" AND 5" WAVY PAPER BACKED A/O H&L SANDING DISCS - 133-823. 2", 3" AND 5" ROUND CLOTH BACKED A/O H&L SANDING DISCS - 131-387. 2", 3" AND 5" WAVY CLOTH BACKED A/O H&L SANDING DISCS - 131-483. 3" HEX SHANK FIRM DISC HOLDERS - 853-042 .
|
|
|
|
Abrasives - Accessories/other
|
A&H ABRASIVES™ DISC SANDER HOOK AND LOOP CONVERSION KIT
|
| 9" H&l Alox 80f Paper Disc
...plus other(s)
|
INSTEAD OF MESSY PSA SANDING DISCS, AN A&H ABRASIVES™ HOOK & LOOP (H&L) CONVERSION KIT ALLOWS YOU TO SWITCH TO MORE CONVENIENT H&L DISCS:
SIMPLY PEEL THE RELEASE LINER OFF OF THE ADHESIVE-BACKED PAD AND PRESS ONTO YOUR SANDER'S STEEL DISC PLATE. H&L SANDING DISCS CAN THEN BE QUICKLY ATTACHED AND REMOVED - NO MORE STICKY GLUE TO CLEAN UP. IF NECESSARY H&L PAD CAN BE REMOVED AND REAPPLIED. SOLD IN PACKAGES OF 3.
|
|
|
|
Advanced Search Tools
Browse
to see Sub Categories)
