|
|
|
Adhesives - Epoxy
|
THESE TWO PART EPOXY ADHESIVE CARTRIDGES SAVE TIME AND MESS
|
| Quick Cure Syringe 50 Ml.
...plus other(s)
|
SYSTEM THREE®, TWO-PART EPOXY SYRINGES MAKE ASSEMBLY JOBS FASTER AND EASIER SINCE THERE IS NO MEASURING OR MESS WHEN USING THE OPTIONAL MIXING TIPS. MIXING TIPS ATTACH TO THE SYRINGE OPENING AND THOROUGHLY MIX THE RESIN AND HARDENER AS THEY PASS THROUGH. SYRINGES MAY BE USED WITHOUT THE MIXING TIPS FOR DISPENSING PRECISE, PRE-MEASURED AMOUNTS AT A 1:1 BY VOLUME RATIO THAT WILL NEED TO BE MIXED BEFORE USE. THESE EPOXIES ARE WATER RESISTANT FOR INDOORS OR OUTDOOR PROJECTS. SYRINGES EASILY SNAP IN AND OUT OF OUR 50 ML EPOXY GUN (949-741) FOR IMPROVED CONVENIENCE AND ASSEMBLY OPERATIONS.
QUICK CURE™ 50 ML. (1.6 OZ.) SYRINGE IS THE STANDARD QUICK SETTING "FIVE MINUTE EPOXY" SYSTEM. QUICK CURE IS IDEAL FOR ALL SMALL JOBS REQUIRING A STRONG BOND AND RAPID CURE. QUICK CURE IS A CLEAR AMBER COLOR. T-88™ 50 ML. (1.6 OZ.) SYRINGE IS A HIGH-PERFORMANCE, NON-BRITTLE, TWO-PART EPOXY ADHESIVE DESIGNED TO GIVE SUPERIOR RESULTS UNDER ADVERSE CONDITIONS. THE ADHESIVE MAY BE USED WITHOUT MODIFICATIONS IN NORMALLY FITTED JOINTS, AND WILL CURE IN ANY THICKNESS WITHOUT SHRINKAGE. T-88 IS CLEAR AMBER AND BECOMES VIRTUALLY INVISIBLE WHEN VARNISHED. T-88 EXHIBITS OUTSTANDING ADHESION AND PERMANENCE ON A WIDE VARIETY OF MATERIALS, AND IS ENDORSED BY LEADING DESIGNERS, BUILDERS AND ORGANIZATIONS. T-88 EPOXIES HAVE A WORK TIME OF 40-60 MINUTES AT 77° AND FULLY FUNCTIONAL STRENGTH IN 24 HOURS. MIXING TIPS (121-016) ARE NOT INCLUDED WITH THE SYRINGES. THEY ARE ONLY AVAILABLE OPTIONALLY IN PACKAGES OF 6 EACH (MIXING TIPS ARE SHOWN ATTACHED TO A SYRINGE.) SYRINGES EACH INCLUDE ONE MANUAL PLUNGER SO THEY MAY BE USED WITH OR WITHOUT A DISPENSING GUN. RE-SEALABLE CAPS HELP MAINTAIN EPOXY QUALITY.
TO HELP COMPLETE YOUR PROJECT, MAY WE SUGGEST:
DISPENSING GUN FOR 50 ML. TWO-PART EPOXY SYRINGES - 949-741.
|
|
|
|
Adhesives - Epoxy
|
SUPER EPOXY AND DISPENSING GUN MAKES APPLICATION CLEAN AND EASY
|
| 50 Ml. Epoxy Cartridge W/2 Mixing Tips
...plus other(s)
|
|
NO MIXING, NO GUESSING. DROP THE EPOXY CARTRIDGES IN THE GUN, PULL THE TRIGGER AND THE EPOXY IS MIXED AND APPLIED. WELL THOUGHT OUT GUN USES DISPOSABLE MIXING NOZZLES SO YOU CAN USE THE GUN AGAIN AND AGAIN. SUPER EPOXY BONDS WOOD, METAL, GLASS, FIBERGLASS CONCRETE JUST ABOUT ANYTHING. REACHES WORKING BOND STRENGTH IN 3-4 HOURS WITH A 15-20 MINUTE OPEN TIME FOR REPOSITIONING THE PIECES.
|
|
|
|
Adhesives - Solvent Based
|
3M™ SUPER 77 MULTIPURPOSE ADHESIVE RESISTS BLEEDING, STAINING OR WRINKLING
|
| 3m Super 77 Spray Adhesive-24 Fl.oz
|
3M™ SUPER 77 MULTIPURPOSE ADHESIVE EASILY SPRAYS ON TO SECURELY BOND LIGHTWEIGHT MATERIALS AND CAN BE USED FOR A VARIETY OF JOBS:
USE FOR PERMANENTLY ATTACHING FOIL, CARPETING, LIGHTWEIGHT PAPER, CARDBOARD, FELT OR CLOTH TO PAINTED OR UNPAINTED METALS, WOOD OR HARDBOARD. HIGH COVERAGE, LOW SOAK-IN AND FAST, AGGRESSIVE TACK MAKE IT A VERY VERSATILE ADHESIVE. LOW VOCS. DOES NOT CONTAIN OZONE DEPLETING CFCS. 16-3/4 OZ. AEROSOL CAN. USA.
TO HELP COMPLETE YOUR PROJECT, MAY WE SUGGEST:
CAN-GUN® - 926-775.
|
|
|
|
Adhesives - Solvent Based
|
TEMPORARY PATTERN MOUNTING ADHESIVES
|
| Repositionable 75 Spray Adhesive
...plus other(s)
|
3M™ REPOSITIONABLE 75 SPRAY ADHESIVE AND H. BEHLEN® MASTER™ SPRAY ADHESIVE ADHERE IN SECONDS, YET HAVE EXTRA LONG TACK RANGES THAT ALLOW YOU TO LIFT AND REPOSITION MATERIALS:
EXCELLENT FOR PRODUCTION LINE WORK WHERE PARTS ARE HELD IN PLACE TEMPORARILY PRIOR TO FINAL ASSEMBLY. BOND PAPER, CARDBOARD, ACETATE, FOIL, FABRICS, SHEETING, ETC. WILL NOT BLEED THROUGH, STAIN OR WRINKLE MOST MATERIALS. USA.
TO HELP COMPLETE YOUR PROJECT, MAY WE SUGGEST:
CAN-GUN® - 926-775.
|
|
|
|
Adhesives - Solvent Based
|
3M™ HI-STRENGTH 90 SPRAY ADHESIVE PROVIDES HIGH CONTACT BOND STRENGTH
|
| Hi Strength 90 Spray Adhesive
|
3M™ HI-STRENGTH 90 AEROSOL ADHESIVE QUICKLY AND SECURELY BONDS HEAVIER MATERIALS:
ONE MINUTE DRY TIME - PRECISE SPRAY CONTROL - HIGH TEMPERATURE RESISTANCE. IDEAL FOR ADHERING POLYETHYLENE OR POLYPROPYLENE TO WOOD, METAL AND MANY OTHER MATERIALS. USE FOR BONDING DECORATIVE LAMINATE EDGES TO TABLES, CABINETS, SHELVING. DRIES CLEAR - 17.6 OZ. AEROSOL CAN; NEW, LOW VOC FORMULA. USA.
TO HELP COMPLETE YOUR PROJECT, MAY WE SUGGEST:
CAN-GUN® - 926-775.
|
|
|
|
Adhesives - Solvent Based
|
READY GRIP CONTACT SPRAY ADHESIVE
|
| Ready Grip Contact Adhesive
|
READY GRIP™ RG25 PRESSURIZED CONTACT ADHESIVE USES AN ADJUSTABLE, VARIABLE SPRAY TIP TO PRODUCE AN EVEN, CONTROLLED DISTRIBUTION OF ADHESIVE:
SPRAY ONTO BOTH SURFACES, ALLOW 2-4 MINUTES TO DRY UNTIL TACKY THEN BOND UP TO 30 MINUTES AFTER APPLICATION. QUICK TACK, FAST DRYING AND HIGH SHEAR STRENGTH. HEAT AND UV-STABLE AND WATER RESISTANT (EXTREMELY POROUS SURFACES LIKE PLYWOOD MIGHT REQUIRE TWO COATINGS). 17 OZ. AEROSOL CAN COVERS 70-80 SQ. FT. USA.
TO HELP COMPLETE YOUR PROJECT, MAY WE SUGGEST:
CAN-GUN® - 926-775.
|
|
|
|
Adhesives - Specialty
|
TWO GLUE GUNS TO SUIT NEARLY ANY NEED IN ANY SHOP
|
| The Leader Glue Gun
...plus other(s)
|
THE HIGH-VOLUME, AD-TECH™ HT LEADER INDUSTRIAL GLUE GUN CAN DELIVER UP TO 4.2 LBS. OF ADHESIVE PER HOUR USING A UNIQUE GRID MELT CHAMBER:
KEEPS UP WITH ALMOST ANY HIGH VOLUME APPLICATION AT A DELIVERY RATE THAT REDUCES HAND FATIGUE - NO HEAT LOSS SLOWDOWNS OR INCREASED FEEDING FORCE. PRESET ELECTRONIC TEMPERATURE CONTROL HOLDS AT 410°F. 120V, 125 WATTS - UL LISTED. LIGHT DUTY MODEL G760 HOT MELT GLUE GUN OPERATES AT 380°F.: METAL STORAGE STAND. 120V, 40W, UL LISTED. USE 1/2" DIA. GLUE STICKS. IMPORTED.
TO HELP COMPLETE YOUR PROJECT, MAY WE SUGGEST:
HOT MELT GLUE STICKS - 895-024.
|
|
|
|
Adhesives - Specialty
|
HIPURFORMER™ POLYURETHANE ADVANCED BONDING SYSTEM GLUES ALMOST ANYTHING
|
| Hipurformer Advanced Bonding System
...plus other(s)
|
THE TITEBOND® HIPURFORMER™ POLYURETHANE ADVANCED BONDING SYSTEM PROVIDES PERMANENT, HIGH STRENGTH, WATERPROOF BONDS THAT VIRTUALLY ELIMINATE THE NEED FOR MECHANICAL FASTENERS. EACH KIT CONTAINS:
A CORDLESS HOT MELT GLUE GUN WITH UP TO 20 MINUTES OFF THE CHARGER USE AND THREE POLYURETHANE HOT MELT ADHESIVE CARTRIDGES: - WW30 - QUICK REPAIRS AND SETUPS (30 SECOND SET TIME)
- WW60 - GAP FILLING (60 SECOND SET TIME).
- MP75 - MULTI-PURPOSE BONDING OF WOOD, MELAMINE, CERAMICS, METAL, MOST PLASTICS, MARBLE, GLASS, FRP, BRICK AND MORE (75 SECOND SET TIME).
ADHESIVE APPLICATOR, CHARGER/STAND, DETACHABLE POWER CORD, WEATHER RESISTANT CASE AND INSTRUCTIONS ALSO INCLUDED.
WITH CAPABILITIES SIMILAR TO MP75, BUT A LONGER SET TIME (5 MINUTES), MP300 MULTI-PURPOSE ADHESIVE HAS BEEN SPECIFICALLY FORMULATED FOR ASSEMBLY WORK (NOT INCLUDED IN KIT). EACH 50G HOT MELT ADHESIVE CARTRIDGE CAN PRODUCE A 1/16" X 71' LINE OF GLUE.
|
|
|
|
Adhesives - Specialty
|
HEAVY DUTY GLUE GUN REACHES OPERATING TEMPERATURE IN MINUTES
|
| Heavy Duty Hot Melt Glue Gun
|
THE ADHESIVE TECH™ ELECTRIC GLUE GUN PRODUCES 410°F. FOR FAST, CONSISTENT GLUE DELIVERY:
ADVANCED ERGONOMIC DESIGN AND LARGE SOLID TRIGGER FOR COMFORTABLE USE. CAN BE STORED ON DETACHABLE, TILT-RESISTANT METAL STAND OR BY USING ATTACHED HANGING RING. 7.5"H X 9.5"L X 2"W - WEIGHS 1.2 LBS. 120V, 200W, 6' CORD, UL LISTED. USES STANDARD 1/2" DIA. GLUE STICKS. IMPORTED.
TO HELP COMPLETE YOUR PROJECT, MAY WE SUGGEST:
HOT MELT GLUE STICKS - 895-024.
|
|
|
|
Adhesives - Tools
|
HOT MELT GLUING DOESN'T HAVE TO LEAVE A MESS
|
| Work Surface 18"x18"
|
IF YOU USE THE ADHESIVE TECH™ WORKSURFACE™ AS THE BASE FOR YOUR HOT MELT GLUE PROJECTS, YOU CAN FORGET ABOUT HAVING TO SPREAD OUT MESSY NEWSPAPERS, WAXED PAPER OR ALUMINUM FOIL FOR PROTECTION:
FLEXIBLE 3/32" THICK X 18" SQUARE WORKSURFACE™ UNROLLS WHEN NEEDED TO PROTECT YOUR WORK AREA. ONCE GLUING IS COMPLETE, SIMPLY BRUSH OR PEEL AWAY COOLED, SOLID GLUE DRIPS AND ACCIDENTAL SPILLS FROM THE NON-STICK SURFACE - REROLL FOR CONVENIENT STORAGE (GLUE GUN, GLUE STICKS, CLAMP AND FURNITURE SHOWN NOT INCLUDED). CAN ALSO BE USED WITH OTHER TYPES OF ADHESIVES. IMPORTED.
LIMITED TO QUANTITIES ON HAND
|
|
|
|
Adhesives - Tools
|
INGENIOUS CAULKING GUN EASILY HANDLES 4 AND 5.5 OZ. TUBES
|
| Formfill Caulking Gun
|
THE FORMFILL® CAULKING GUN IS LIGHTWEIGHT, EASY TO USE, VERSATILE, COST EFFICIENT AND SAVES MONEY:
FITS MOST 4 AND 5.5 OZ. TUBES OF CAULKS AND ADHESIVES, ELIMINATING THE NEED FOR 10 OZ. CARTRIDGES. UNIQUE CONTROLLED-FLOW DESIGN (LETTING UP THE TRIGGER STOPS THE FLOW) GIVES UNPRECEDENTED ACCURACY AND ELIMINATES WASTE. APPLIES PERFECT BEADS DOWN TO THE LAST DROP WITH NO STOPS AND STARTS, OVERFILLS AND BREAKS. IDEAL FOR CRAMPED AND HARD-TO-REACH PLACES.
|
|
|
|
Adhesives - Tools
|
HOT MELT GLUE GUN CAN BE USED ALMOST ANYWHERE
|
| Cordless Glue Gun
|
READY TO USE IN JUST 3 MINUTES, THE COMPACT AD TECH CB1000 CORDLESS GLUE GUN IS PERFECTLY SUITED FOR MOST JOBS AND IS COMPLETELY PORTABLE:
PRODUCES 383°F AND USES STANDARD 1/2" DIA. GLUE STICKS (NOT INCLUDED). UP TO A 120 MINUTE RUN TIME - REFILLABLE IN 10 SECONDS OR LESS USING BUTANE LIGHTER FLUID (NOT INCLUDED). ALL IN ONE ON/OFF SWITCH, GAS LEVEL WINDOW AND DETACHABLE SAFETY STAND. 6-1/4"H X 1-1/4"W X 6-1/4"L. IRELAND.
TO HELP COMPLETE YOUR PURCHASE, MAY WE SUGGEST:
GENERAL PURPOSE 4" CLEAR GLUE STICKS - 895-016.
|
|
|
|
Adhesives - Tools
|
EPOXY DISPENSING GUN MAKES APPLICATION CLEAN AND QUICK
|
| 50 Ml Dispensing Gun
...plus other(s)
|
|
NO MIXING AND NO GUESSING WHEN USING THE DISPENSING GUN. SIMPLY DROP ONE 50ML INJECTOR CARTRIDGE INTO DISPENSING GUN, ATTACH THE MIXING NOZZLE TIP AND PULL THE TRIGGER. EPOXY IS MIXED AND APPLIED USING THE MIXING TIP; NO DRIP - APPLY TO BOTH VERTICAL AND OVERHEAD SURFACES: BONDS WOOD, METAL, GLASS, FIBERGLASS, CONCRETE - JUST ABOUT ANYTHING. EPOXY HAS A 15-20 MINUTE OPEN TIME; REACHES WORKING BOND STRENGTH IN 3-4 HOURS. 949-734 50ML. INJECTOR CARTRIDGE INCLUDES (2) MIXING TIPS AND (1) CAP FOR SEALING UP AFTER USE. 949-748 DISPOSABLE STATIC MIXING NOZZLES COME IN A (PKG. OF 2). 964-517 EPOXY GUN KIT INCLUDES DISPENSING GUN, (1)50ML EPOXY INJECTOR CARTRIDGE WITH (2) MIXING NOZZLE TIPS. 949-741 EPOXY GUN IS THE GUN ONLY AND DOES NOT INCLUDE ANY CARTRIDGES OR MIXING TIPS.
|
|
|
|
Air Tool Accessories - Filters Regulators & Lubes (frl's)
|
CAMPBELL HAUSFELD™ IN-LINE AIR FILTER PROTECTS TOOLS, HELPS PREVENT SPRAY GUN FINISH CONTAMINATION
|
| 3/8" Inline Water Filter W/bowl Gurad
|
THE FIVE-MICRON CAMPBELL HAUSFELD™ PA2121 IN-LINE AIR FILTER TRAPS MOISTURE AND FOREIGN MATTER TO EXTEND TOOL LIFE:
SEE-THROUGH BOWL WITH METAL GUARD ALLOWS EASY MONITORING OF FLUID LEVEL WHILE PROTECTING UNIT AGAINST IMPACT. QUICK-RELEASE BOWL AND QUARTER-TURN DRAIN ALLOW EASY MAINTENANCE. 57 SCFM @ 90 PSI - 150 PSI MAXIMUM PRESSURE. 3/8" FEMALE NPT PORTS. ONE-YEAR MANUFACTURER'S WARRANTY. USA.
|
|
|
|
Air Tool Accessories - Filters Regulators & Lubes (frl's)
|
MINI SIZE, COMPRESSED AIR REGULATORS PACK PERFORMANCE INTO SMALL PACKAGES
|
| 0-125 Psi Mini Regulator For Nail Guns
...plus other(s)
|
THESE VERSATILE RTI MINI REGULATORS CAN HELP PROVIDE SMOOTHER FINISHES AND BETTER PERFORMANCE BY ELIMINATING AIR PRESSURE FLUCTUATIONS CAUSED BY UPSTREAM PRESSURE SWINGS:
927-230 (R-99) - 1/4" REGULATOR/GAUGE:
0-100 PSI ADJUSTABLE RANGE, 24 CFM @ 100 PSI. 0-100 PSI GAUGE. NPT THREAD. 150°F., 250 PSIG MAX. TEMPERATURE AND PRESSURE. 2-3/4"L X 1-1/2" DIA., WEIGHS 0.25 LBS.
132-497 (MR1120-02G) - 1/4" REGULATOR/GAUGE:
0-125 PSI ADJUSTABLE RANGE, 30 CMF @ 100 PSI. 0-160 PSI GAUGE. NPT THREAD. 125°F., 225 PSIG MAX. TEMPERATURE AND PRESSURE. 3"L X 1-3/4" DIA., WEIGHS 0.3 LBS. (INCLUDES NUT FOR PANEL MOUNT APPLICATIONS - FITS INTO A 1-3/16" DIA. HOLE). USA.
|
|
|
|
Air Tool Accessories - Fittings
|
AIR HOSES, REELS AND BLOW GUNS DESIGNED FOR RUGGED JOB SITE CONDITIONS
|
| Ag2-10 Extendable Blow Gun
...plus other(s)
|
LEGACY™ CONTRACTOR™ SERIES AIR REELS ARE LOADED WITH DESIGN FEATURES - BAKED ENAMEL FINISH, REINFORCED STEEL WITH TAPERED SIDE WALLS, 3' LEAD-IN HOSES AND BRAKES TO KEEP HOSE FROM UNWINDING AND SWIVEL HANDLES AND BRACKETS FOR WALL, WORKBENCH OR VEHICLE USE:
L8650 100' CAPACITY REEL INCLUDES 50' WORKFORCE™ SERIES AIR HOSE: 15-3/8" X 10-5/8" X 13-1/8" REEL - HOSE AND REEL WEIGH 18.63 LBS. L8652 200' CAPACITY REEL COMES WITH 100' WORKFORCE™ SERIES HOSE: 19-7/16" X 10-5/8" X 12" REEL - HOSE AND REEL WEIGH 22.88 LBS. HOSES ARE 3/8" I.D. REINFORCED PVC WITH SOLID 1/4" BRASS NPT FITTINGS AND BEND RESTRICTORS TO PROLONG HOSE LIFE - 350 PSI MAXIMUM WORKING PRESSURE.
AG2-10 BLOW GUN EXTENDS FROM 6-1/2" TO 11", SWIVELS 360° AND HAS A REMOVABLE RUBBER SCRATCH GUARD TIP - 1/4" NPT BRASS AIR INLET THREAD: 13 CFM @ 90 PSI WITH 1/4" HOSE; 15 CFM WITH 3/8" HOSE - 110 MAXIMUM PSI. USA.
|
|
|
|
Air Tool Accessories - Fittings
|
HIGH-VOLUME BLOW GUN MAKES HEAVY-DUTY CLEAN-UPS EASIER
|
| Typhoon Blow Gun
...plus other(s)
|
DELIVERING UP TO 51 CFM AND OVER 3 LBS. OF THRUST AT 125 PSI, COILHOUSE PNEUMATICS® TYPHOON HIGH-VOLUME BLOW GUN IS IDEAL FOR HEAVY-DUTY CLEAN-UP AND BLOW-OFF OF EVEN THE HEAVIEST CHIPS AND SHAVINGS - MEETS OR EXCEEDS OSHA REGULATIONS:
130-160 - MODEL TYP-3800CS 3/8" NPT BLOW GUN IS LIGHTWEIGHT AND ERGONOMIC: 10-1/2"L X 5-3/4"W X 2-1/8" H, WEIGHS 6.2 OZ. COMES WITH MJN-0-DL MULTI-JET AND HFN-00F-DL HIGH FLOW TIPS (FEMALE).
120-941 - MODEL 1506BS - OPTIONAL 3/8" INDUSTRIAL BALL SWIVEL CONNECTOR ADDS FLEXIBLE TOOL-TO-HOSE CONNECTIVITY: 1/4" DIA. HOSE CONNECTOR AND NUT ARE NICKEL-PLATED, HARDENED STEEL - 3/8" DIA. MALE THREAD IS ALL BRASS.
ONE-YEAR MANUFACTURER'S WARRANTY. IMPORTED.
|
|
|
|
Air Tool Accessories - Fittings
|
A COMPACT INLINE BLOWGUN WILL END HUNTING FOR YOUR STANDARD BLOWGUN
|
| Inline Blow Gun W/ Osha Tip
...plus other(s)
|
SIMPLY SCREW A COILHOSE PNEUMATICS® 600 SERIES IN-LINE BLOWGUN ONTO THE END OF YOUR AIR HOSE, INSTALL A QUICK CONNECT COUPLING ON THE BLOWGUN'S OPPOSITE END AND YOU WILL ALWAYS KNOW WHERE THIS HANDY TOOL IS LOCATED:
UNIQUE "FULL FLOW" DESIGN WILL NOT RESTRICT DOWNSTREAM AIR FLOW. 150 PSI RATING; 32° TO +175°F. OPERATING RANGE. 1/4" NPT FEMALE THREADS; 1/8" DIA. NOZZLE PORT. REPLACEABLE METAL OSHA TIP MEETS APPROVED SAFETY STANDARDS; REPLACEABLE RUBBER TIP FEATURES A CONICAL SHAPE. 1-5/8"H X 3/4"W X 1-7/8"L CHROME PLATED ZINC BODY; WEIGHS 0.2 LBS. 834-793 - QUICK CONNECT COUPLING SOLD SEPARATELY (AIR HOSE NOT INCLUDED).
|
|
|
|
Air Tool Accessories - Fittings
|
TAMPER PROOF AIR TOOL SAFETY BLOW GUN
|
| Tamper Proof Safety Blow Gun
|
TIP SWIVELS FREELY, YET CANNOT BE REMOVED:
TIP PRESSURE WILL NOT EXCEED 30 PSI, YET PROVIDES AN EXCELLENT BLAST OF AIR FOR CLEANING. 1/4" NPT. USA.
|
|
|
|
Air Tool Accessories - Fittings
|
DYNABRADE® SPRAYGUN SWIVEL™ REDUCES OPERATOR FATIGUE
|
| 1/4" Spray Gun Swivel
|
THE DYNABRADE® MODEL 95586 SPRAYGUN SWIVEL™ ALLOWS AN AIR HOSE TO HANG STRAIGHT TO THE FLOOR AND OUT OF THE WAY, NO MATTER HOW THE GUN IS TURNED, IMPROVING CONTROL AND ELIMINATING KINKED HOSES:
CONNECTS TO AIR HOSE WITH 1/4" FEMALE NPT FITTING AND TO SPRAY GUN WITH 1/4"-18 FEMALE NPSM FITTING. BUILT-IN FLOW CONTROL KNOB WITH EASY-TO-READ GAUGE. HANDLES UP TO 25 CFM - NOT TO EXCEED 150 PSI. WEIGHS 1/2 LB. NOTE: SPRAY GUN USE ONLY - NOT FOR USE WITH PERCUSSION TOOLS.
LIMITED TO QUANTITIES ON HAND
|
|
|
|
Advanced Search Tools
Browse
symbol next to the category that matches your desired product and select a sub-category link.
