|
|
|
Abrasives - Accessories/hand Sanding
|
A&H ABRASIVESTM ABRASIVE FINISHING SPONGES
|
| Soft Hand Pad-very Fine
...plus other(s)
|
DURING THE WET SANDING PROCESS, ABRASIVE FINISHING SPONGES HEAT DANISH OIL APPLIED TO THE WOOD'S SURFACE, TURNING IT INTO A "GRAVY" THAT SOAKS IN, FILLS THE GRAIN AND LEAVES A BEAUTIFUL SHEEN:
SOLD IN PACKAGES OF 10 AND AVAILABLE IN FIVE GRITS TO MEET YOUR SPECIFIC REQUIREMENTS: COARSE (36-80); MEDIUM (80-120); FINE (120-180); VERY FINE (180-220); AND SUPER FINE (220-400). 1/2" X 3-3/4" X 4-3/4". CLEAN WITH MINERAL SPIRITS TO REUSE.
TO HELP COMPLETE YOUR PROJECT, MAY WE SUGGEST:
J.E. MOSER'S® DANISH OIL - 859-973.
|
|
|
|
Abrasives - Belts/aluminum Oxide (y-weight)
|
WASHABLE SANDING BELTS ARE MADE TO LAST LONGER
|
| 6"x132" Alox 36y Sanding Belt
...plus other(s)
|
A&H ABRASIVES BELTS ARE MADE FROM THE FINEST QUALITY MATERIALS. THE PREMIUM GRADE FRIABLE ALUMINUM OXIDE BREAKS AWAY IN USE TO EXPOSE NEW SHARP EDGES. THE ABRASIVE IS BONDED TO THE Y-WEIGHT POLYESTER BACKING WITH INDUSTRIAL STRENGTH PROPRIETARY RESINS IN AN OPEN COAT (50-80% GRAIN COVERAGE) ARRANGEMENT TO ALLOW MAXIMUM STOCK REMOVAL WITH MINIMUM LOADING. THE Y-WEIGHT BACKING IS FLEXED WHICH ENHANCES FLEXIBILITY AND DOES NOT INTERFERE WITH BELT INTEGRITY. THE BELTS FEATURE BI-DIRECTIONAL, HIGH-STRENGTH, NO-BUMP, URETHANE-BONDED MYLAR® BUTT JOINTS THAT CAN BE RUN IN EITHER DIRECTION INCREASING THE TOTAL SERVICE LIFE OF THE BELT. THE 6" X 132" AND 6" X 280" BELTS ARE AVAILABLE IN GRIT RANGE 36-220 (SEE SIZES FOR SPECIFIC GRITS). MADE IN WYOMING, USA WITH COMPONENTS FROM USA AND KOREA.
PREMIUM ALUMINUM OXIDE GRAIN DELIVERS SHARP AND DURABLE PERFORMANCE. RESIN BOND ANCHORS THE ABRASIVE TO THE BACKING FOR LONGER BELT LIFE. HEAVY Y-WEIGHT POLYESTER BACKING IS TEAR RESISTANT AND TRACKS MORE CONSISTANT. 6" X 132" AND 6" X 280" BELTS. THE BEST BELTS FOR GENERAL WOODWORKING. BI-DIRECTIONAL, HIGH-STRENGTH, NO-BUMP, URETHANE-BONDED MYLAR® BUTT JOINTS.
|
|
|
|
Abrasives - Belts/aluminum Oxide (y-weight)
|
25" X 60" AND 36" X 60" WASHABLE SANDING BELTS MADE TO LAST LONGER
|
| 25"x60" Alox 36y Sanding Belt
...plus other(s)
|
A&H ABRASIVES BELTS ARE MADE FROM THE FINEST QUALITY MATERIALS. THE PREMIUM GRADE FRIABLE ALUMINUM OXIDE BREAKS AWAY IN USE TO EXPOSE NEW SHARP EDGES. THE ABRASIVE IS BONDED TO THE Y-WEIGHT POLYESTER BACKING WITH INDUSTRIAL STRENGTH PROPRIETARY RESINS IN AN OPEN COAT (50-80% GRAIN COVERAGE) ARRANGEMENT TO ALLOW MAXIMUM STOCK REMOVAL WITH MINIMUM LOADING. THE Y-WEIGHT BACKING IS FLEXED WHICH ENHANCES FLEXIBILITY AND DOES NOT INTERFERE WITH BELT INTEGRITY. THE BELTS FEATURE BI-DIRECTIONAL, HIGH-STRENGTH, NO-BUMP, URETHANE-BONDED MYLAR® BUTT JOINTS THAT CAN BE RUN IN EITHER DIRECTION INCREASING THE TOTAL SERVICE LIFE OF THE BELT. THE 17" X 54" AND 25" X 60" BELTS ARE AVAILABLE IN GRIT RANGE 36-220 (SEE SIZES FOR SPECIFIC GRITS). MADE IN WYOMING, USA WITH COMPONENTS FROM USA AND KOREA.
PREMIUM ALUMINUM OXIDE GRAIN DELIVERS SHARP AND DURABLE PERFORMANCE. RESIN BOND ANCHORS THE ABRASIVE TO THE BACKING FOR LONGER BELT LIFE. HEAVY Y-WEIGHT POLYESTER BACKING IS TEAR RESISTANT AND TRACKS MORE CONSISTANT. 17" X 54" AND 25" X 60" BELTS. THE BEST BELTS FOR GENERAL WOODWORKING. BI-DIRECTIONAL, HIGH-STRENGTH, NO-BUMP, URETHANE-BONDED MYLAR® BUTT JOINTS.
|
|
|
|
Abrasives - Belts/aluminum Oxide (y-weight)
|
43" X 75", 50" X 103" AND 52" X 75" WASHABLE SANDING BELTS MADE TO LAST LONGER
|
| 43"x75" Alox 36y Sanding Belt
...plus other(s)
|
A&H ABRASIVES BELTS ARE MADE FROM THE FINEST QUALITY MATERIALS. THE PREMIUM GRADE FRIABLE ALUMINUM OXIDE BREAKS AWAY IN USE TO EXPOSE NEW SHARP EDGES. THE ABRASIVE IS BONDED TO THE Y-WEIGHT POLYESTER BACKING WITH INDUSTRIAL STRENGTH PROPRIETARY RESINS IN AN OPEN COAT (50-80% GRAIN COVERAGE) ARRANGEMENT TO ALLOW MAXIMUM STOCK REMOVAL WITH MINIMUM LOADING. THE Y-WEIGHT BACKING IS FLEXED WHICH ENHANCES FLEXIBILITY AND DOES NOT INTERFERE WITH BELT INTEGRITY. THE BELTS FEATURE BI-DIRECTIONAL, HIGH-STRENGTH, NO-BUMP, URETHANE-BONDED MYLAR® BUTT JOINTS THAT CAN BE RUN IN EITHER DIRECTION INCREASING THE TOTAL SERVICE LIFE OF THE BELT. THE 43" X 75", 50" X 103" AND 52" X 75" BELTS ARE AVAILABLE IN GRIT RANGE 36-220 (SEE SIZES FOR SPECIFIC GRITS). MADE IN WYOMING, USA WITH COMPONENTS FROM USA AND KOREA.
PREMIUM ALUMINUM OXIDE GRAIN DELIVERS SHARP AND DURABLE PERFORMANCE. RESIN BOND ANCHORS THE ABRASIVE TO THE BACKING FOR LONGER BELT LIFE. HEAVY Y-WEIGHT POLYESTER BACKING IS TEAR RESISTANT AND TRACKS MORE CONSISTANT. 43" X 75", 50" X 103" AND 52" X 75" BELTS. THE BEST BELTS FOR GENERAL WOODWORKING. BI-DIRECTIONAL, HIGH-STRENGTH, NO-BUMP, URETHANE-BONDED MYLAR® BUTT JOINTS.
|
|
|
|
Abrasives - Belts/aluminum Oxide (y-weight)
|
37" X 60" AND 37" X 75" WASHABLE SANDING BELTS MADE TO LAST LONGER
|
| 37"x60" Alox 36y Sanding Belt
...plus other(s)
|
A&H ABRASIVES BELTS ARE MADE FROM THE FINEST QUALITY MATERIALS. THE PREMIUM GRADE FRIABLE ALUMINUM OXIDE BREAKS AWAY IN USE TO EXPOSE NEW SHARP EDGES. THE ABRASIVE IS BONDED TO THE Y-WEIGHT POLYESTER BACKING WITH INDUSTRIAL STRENGTH PROPRIETARY RESINS IN AN OPEN COAT (50-80% GRAIN COVERAGE) ARRANGEMENT TO ALLOW MAXIMUM STOCK REMOVAL WITH MINIMUM LOADING. THE Y-WEIGHT BACKING IS FLEXED WHICH ENHANCES FLEXIBILITY AND DOES NOT INTERFERE WITH BELT INTEGRITY. THE BELTS FEATURE BI-DIRECTIONAL, HIGH-STRENGTH, NO-BUMP, URETHANE-BONDED MYLAR® BUTT JOINTS THAT CAN BE RUN IN EITHER DIRECTION INCREASING THE TOTAL SERVICE LIFE OF THE BELT. THE 37" X 60" AND 37" X 75" BELTS ARE AVAILABLE IN GRIT RANGE 36-220 (SEE SIZES FOR SPECIFIC GRITS). MADE IN WYOMING, USA WITH COMPONENTS FROM USA AND KOREA.
PREMIUM ALUMINUM OXIDE GRAIN DELIVERS SHARP AND DURABLE PERFORMANCE. RESIN BOND ANCHORS THE ABRASIVE TO THE BACKING FOR LONGER BELT LIFE. HEAVY Y-WEIGHT POLYESTER BACKING IS TEAR RESISTANT AND TRACKS MORE CONSISTANT. 37" X 60" AND 37" X 75" BELTS. THE BEST BELTS FOR GENERAL WOODWORKING. BI-DIRECTIONAL, HIGH-STRENGTH, NO-BUMP, URETHANE-BONDED MYLAR® BUTT JOINTS.
|
|
|
|
Adhesives - Accessories
|
J.E. MOSER'S BLACKLITE WOOD GLUE ADDITIVE
|
| Blacklite Glue Additive
...plus other(s)
|
MIX ONE OUNCE OF BLACKLITE™ GLUE ADDITIVE INTO ONE GALLON OF GLUE, AND YOU'LL NEVER MISS A SPECK OF GLUE AGAIN:
UNDER NORMAL LIGHT, GLUE WILL APPEAR TRANSPARENT - UNDER BLACK LIGHT (NOT INCLUDED), THE ADDITIVE IN THE GLUE WILL SHINE BRIGHTLY. NO MORE SCRUTINIZING EVERY NOOK AND CRANNY OF YOUR WOODWORKING PROJECTS BEFORE STAINING. SOLD IN PACKAGES OF TWO OR SIX, ONE OZ. BOTTLES - USE WITH ALIPHATIC GLUES ONLY. USA.
|
|
|
|
Adhesives - Instant
|
J. E. MOSER'S® LOW ODOR LIGHTNING BOND™ MAKES USING INSTANT GLUES MORE ENJOYABLE
|
| Low Odor Thin Lightning Bond-1oz.
...plus other(s)
|
ODOR LEVELS HAVE BEEN DRAMATICALLY REDUCED MAKING LOW ODOR LIGHTNING BOND™ MUCH MORE COMFORTABLE TO USE INDOORS BY MANY CRAFTSMEN WHO ARE SENSITIVE TO NORMAL CA GLUE FUMES. I ALSO NOTICE THAT MY EYES DON'T STING WHEN WORKING WITH THIS INSTANT GLUE. LOW ODOR LIGHTNING BOND™ SUPER GLUE IS IDEAL FOR QUICKLY ADHERING SURFACES WITHOUT CLAMPING AND REPAIRING CRACKS QUICKLY - A TREMENDOUS TIME SAVER. IT IS ALSO VERY USEFUL FOR FINISHING SMALL TURNINGS ON THE LATHE. THIS GLUE IS FORMULATED FOR ADHERING WOOD BUT WILL BOND VIRTUALLY ANYTHING INCLUDING CLOTH, GLASS, LEATHER, PAPER, METAL, MOST PLASTICS, STONE, WOOD, ETC. IT WILL NOT BOND TEFLON®, HIGH-DENSITY POLYETHYLENE OR POLYPROPYLENE ON IT'S OWN. WORKS BEST ON TIGHT FITTING JOINTS, BUT MANY LOOSE FITTING JOINTS CAN ALSO BE SUCCESSFULLY BONDED USING THE THICK. WORKING TIMES VARY BUT AVERAGE AROUND 30 SECONDS FOR THE THIN VISCOSITY WHEN APPLIED TO SNUG FITTING JOINTS. MEDIUM AND THICK VISCOSITY INSTANT GLUES HAVE SLIGHTLY LONGER TACK TIMES. ADD LIGHTNING ACTIVATOR TO GREATLY REDUCE TACK-UP TIME OF ALL VISCOSITIES. PLEASE ALLOW ALL CYANOACRYLATE(CA) INSTANT, SUPER GLUES APPROXIMATELY 24 HOURS TO FULLY CURE FOR MAXIMUM STRENGTH.
THIN VISCOSITY FOR REPAIRING HAIRLINE CRACKS AND FINISHING. MEDIUM VISCOSITY HIGHER VISCOSITY, GAP FILLING. THICK VISCOSITY EXTRA THICK, GAP FILLING. ACTIVATOR ACCELERATES ANY INSTANT GLUE TO MAKE IT TRULY "INSTANT". DEBONDER REMOVES GLUE FROM HANDS, TOOLS. USA.
|
|
|
|
Adhesives - Instant
|
J.E. MOSER'S® LIGHTNING BOND™ SUPER GLUE - THIN
|
| Lightning Bond Debonder-2oz.
...plus other(s)
|
FILL HAIRLINE CRACKS OR LARGE GAPS WITH J. E. MOSER'S® LIGHTNING BOND™ HIGH PERFORMANCE CYANOACRYLATE INSTANT GLUES - A VARIETY OF VISCOSITIES, FROM THIN TO SUPER THICK, MEANS YOU CAN MEET VIRTUALLY ANY GLUING NEED:
ADD LIGHTNING ACTIVATOR TO GREATLY REDUCE TACK-UP TIME. AVAILABLE SEPARATELY OR INSIDE THE LIGHTNING BOND™ GLUE KIT ALONG WITH EVERYTHING ELSE YOU NEED TO GET STARTED. KIT INCLUDES 1 OZ., EACH, THIN, MEDIUM AND THICK VISCOSITY GLUE, 2 OZ. ACTIVATOR, 2 OZ. DEBONDER, 3/4 OZ. SQUEEZ-DROP PRECISION APPLICATOR BOTTLE WITH LOCKING CAP, 3 FLEXIBLE AND 5 TAPERED TIPS PLUS PLASTIC STORAGE CASE. CYANOACRYLATES CURE FULLY IN 24 HOURS. THIN VISCOSITY LIGHTNING BOND™ IS PERFECT FOR HAIRLINE CRACKS - TACKS UP IN 1-3 SECONDS. 2 OZ. MEDIUM VISCOSITY LIGHTNING BOND™ FILLS MOST SMALL GAPS - 5-15 SECOND TACK-UP TIME. 2 OZ. THICK VISCOSITY LIGHTNING BOND™ IS EXTRA THICK FOR LARGE GAPS - TACKS UP IN 10-25 SECONDS. 2 OZ. SUPER THICK GEL LIGHTNING BOND™ IS BEST FOR GAPS UP TO 0.01" - TACKS UP IN 45 SECONDS. 0.07 OZ. (20G). DEBONDER SOFTENS CURED GLUES AND REMOVES GLUE FROM HANDS AND TOOLS. 2 OZ. USA.
|
|
|
|
Adhesives - Specialty
|
J.E. MOSER'S HIDE WOOD GLUE
|
| Pearl Hide Glue
...plus other(s)
|
THIS IS THE SAME TYPE OF NATURAL HIDE GLUE THAT HAS BEEN USED BY WOODWORKERS FOR HUNDREDS OF YEARS DUE IT'S DURABILITY AND VERSATILITY, FAST TACKING AND STRONG JOINTS. TO PREPARE J.E. MOSER'S® HIDE GLUES MIX ABOUT 50/50 WITH COOL WATER AND WARM TO APPROXIMATELY 140° F. BEFORE USE. FOR RE-GLUING AN OLD HIDE GLUE JOINT YOU CAN JUST ADD MORE GLUE WITHOUT SCRAPING:
849-755 - PEARL HIDE GLUE(164 GRAM STRENGTH) IS AN ALL PURPOSE GLUE SUITABLE FOR MOST APPLICATIONS. 893-961 - GROUND HIDE GLUE (251 GRAM STRENGTH) IS A PURER GRADE FOR APPLICATIONS REQUIRING HIGHER TACK AND STRONGER BOND. BOTH ARE STRONGER THAN COMMERCIALLY PREPARED LIQUID HIDE GLUES WHEN PROPERLY MIXED. ALTHOUGH THESE HIDE GLUES PROVIDE QUICK GRAB, THEY ALLOW REPOSITIONING FOR AN EXTENDED PERIOD. NOTE: WHEN GLUING SOFT WOODS, 100-150 PSI CLAMPING PRESSURE IS RECOMMENDED - 175-250 PSI FOR HARDWOODS.
849-783 - THE THERMOSTAT EQUIPPED ELECTRIC GLUE POT WILL MAINTAIN 140° TO 150° F. AND NOT BURN GLUE: REMOVABLE, ONE QUART SPUN ALUMINUM CONTAINER WITH WIPER ROD INCLUDED FOR EASY CLEANING. 115V; UL APPROVED.
|
|
|
|
Adhesives - Specialty
|
GROUND RABBIT SKIN GLUE SAVES YOU TIME AND EFFORT
|
| Ground Rabbit Skin Glue
|
A DOMESTIC HIDE GLUE, RABBIT SKIN GLUE IS DRIED AND GROUND AND READY TO USE:
JUST ADD HOT WATER AND FOLLOW THE DIRECTIONS. MIX WITH GILDER'S WHITING AND ADDITIONAL WATER TO FORM A MOLDABLE GESSO FOR REPAIRING DAMAGE TO ORNATE ANTIQUE PICTURE FRAMES; ALSO USED BY GILDERS. SOLD IN 1 LB. CONTAINERS.
TO HELP COMPLETE YOUR PROJECT, MAY WE SUGGEST:
849-909 - GILDER'S WHITING.
|
|
|
|
Adhesives - Specialty
|
GUM COPAL FINISH RESIN
|
| Yellow Beeswax Prills
...plus other(s)
|
THESE MATERIALS ARE OFFERED FOR RESTORERS AND ARTISTS WHO ONLY WANT TO USE TRADITIONAL METHODS IN MIXING AND PRODUCING THEIR OWN FINISHING MATERIALS:
DISSOLVE OR MIX THE SOLID MATERIALS WITH ALCOHOL OR OTHER PRODUCTS TO PRODUCE TRADITIONAL PIGMENT COLORS OR THE FINEST SPIRIT VARNISHES AND LACQUERS OR SPIRIT GLAZES FOR FRENCH POLISHING.
LIMITED TO QUANTITIES ON HAND
|
|
|
|
Adhesives - Specialty
|
J.E. MOSER'S HOT GLUE STICKS
|
| 10" High Performance Hot Glue Sticks
...plus other(s)
|
SELECT FROM THREE DIFFERENT HOT MELT GLUES TO MATCH YOUR NEEDS. J.E. MOSER'S® 7/16" DIAMETER, GLUE STICKS FEED VERY EVENLY AND SMOOTHLY IN MOST 1/2" CAPACITY HOT MELT GLUE GUNS. TYPICAL USES INCLUDE CABINET AND FURNITURE ASSEMBLY, TRIM ATTACHMENT, SPEAKER GRILLS, MIRRORS, FABRIC AND UPHOLSTERY. ALL OUR HOT MELT GLUE STICKS ARE NON-TOXIC AND MEET FDA ADHESIVE REQUIREMENTS FOR INDIRECT FOOD CONTACT:
ECONOMY - COST EFFECTIVE GLUE FOR GENERAL BONDING OF MANY PLASTICS, WOOD, AND OTHER POROUS MATERIALS. GENERAL PURPOSE - GOOD FOR BONDING PLASTIC, GLASS, STEEL, WOOD, AND OTHER POROUS MATERIALS. HIGH PERFORMANCE - DESIGNED SPECIFICALLY FOR WOODWORKING APPLICATIONS WITH HIGH BOND STRENGTH AND MEDIUM VISCOSITY FOR HIGH DELIVERY RATES.
APPROXIMATELY 45 4" STICKS PER LB.; 18 10" STICKS PER LB.
|
|
|
|
Adhesives - Specialty
|
J.E. MOSER'S® CRITICAL BOND POLYURETHANE WOOD GLUE
|
| Critical Bond Polyurethane Glue
...plus other(s)
|
|
|
|
Adhesives - Tools
|
SYSTEM THREE 0100A16 EPOXY RESIN ADHESIVE SYSTEM
|
| 12 Oz. Mixing Cups
...plus other(s)
|
WHETHER YOU'RE BUILDING, RESTORING OR REPAIRING WITH WOOD, FIBERGLASS OR COMPOSITES, YOU CAN EASILY MODIFY THE VERSATILE SYSTEM THREE® EPOXY ADHESIVE SYSTEM TO SUIT ALMOST ANY APPLICATION:
PERMANENTLY BOND OLD AND NEW JOINTS. LAMINATE BEAMS OR OTHER OBJECTS. SEAL INTERIOR AND EXTERIOR SURFACES. SUITABLE FOR DAMP LOCATIONS. SYSTEM BASED UPON LOW VISCOSITY, MODIFIED EPOXY RESIN MIXED AT A 2:1 VOLUME RATIO WITH ONE OF THREE HARDENERS:
#1 - 15 MINUTE WORKING TIME, CURES DOWN TO 35 DEGREES F.;#2 - WORKS ABOVE 55 DEGREES F., 30 MINUTE WORKING TIME; AND#3 - USED ABOVE 75 DEGREES F., 70 MINUTE WORKING TIME.
WHEN PROPERLY MIXED, EPOXY IS READY "AS IS" FOR COATING, FIBERGLASSING OR GLUING. FOR GLUING REQUIRING GAP FILLING OR FLOW CONTROL, AND ALL FILLETING WORK, THICKENERS ARE REQUIRED. 3105S16 SILICA THICKENER INCREASES VISCOSITY AND PRODUCES A NON-SAGGING FIRM PASTE. 3110S16 WOOD FLOUR IS FINE SAWDUST; EXCELLENT FOR CREATING GLUES AND STRUCTURAL FILLETS. OPTIONAL MEASURING AND MIXING TOOLS SPEED EPOXY PREPARATION AND APPLICATION. USA.
|
|
|
|
Adhesives - Tools
|
CRITICAL BOND II AND GLUE WELL
|
| Critical Bond Ii And Glue Well
...plus other(s)
|
WITH A CAPACITY OF ALMOST 29 OZ., GLUE WELL DOES NOT REQUIRE CONSTANT FILLING AND ITS WIDE, 2-1/2" DIA. MOUTH MAKES IT EASY TO GET JUST THE RIGHT AMOUNT OF GLUE ONTO YOUR BRUSH:
INTEGRATED SPOUT MAKES FILLING SIMPLE. TIGHT FITTING LID CAN ACCOMMODATE A NARROW HANDLE BRUSH UP TO 2"W X 7"L (INCLUDING BRISTLES) AND HELPS KEEP THE BRUSH AND GLUE FROM DRYING OUT. LID STORES ON TOP WHEN GLUE WELL IS BEING USED. DURABLE, WASHABLE, BREAK RESISTANT PLASTIC. IMPORTED. 981-864 - GLUE WELL SET INCLUDES A 16 OZ. BOTTLE OF CRITICAL BOND II™ WOODWORKER'S GLUE.
|
|
|
|
Adhesives - Tools
|
GLUE SYRINGES AND INJECTORS
|
| Set Of 5 1" Tips
...plus other(s)
|
FASTER, MORE ACCURATE AND TIDIER GLUING IS ALMOST ASSURED WHEN YOU USE GLUE INJECTORS:
178-001 - 10CC TAPER POINT IS A MOLDED ONE PIECE INJECTOR. 910-144, 910-151 - 10CC OR 20CC SYRINGE HAS REMOVABLE 1" AND 1-1/2" TIPS. FIVE PACKS INCLUDE ONLY SYRINGES OR TIPS. 891-903, 891-541 - INJECTOR BOTTLES ARE USEFUL WITH GLUE AS WELL AS OIL. 897-541 - SAVE MONEY WITH AN ECONOMY 12 PACK OF 15CC INJECTORS!
|
|
|
|
Adhesives - Tools
|
J.E. MOSER'S 20252 GLUE BOTTLE AND CAP WITH WSI LOGO - 16OZ.
|
| Wsi 16oz Glue Bottle And Cap
...plus other(s)
|
WOODWORKER'S SUPPLY® 16 OZ. SQUEEZE BOTTLE WITH CAP IS HANDY FOR STORING AND POURING BULK GLUE:
ONE OZ. MIXING CUPS ARE GREAT FOR MIXING SMALL AMOUNTS OF EPOXIES OR STAINS. POLYPROPYLENE RESISTS MOST STAINS AND SOLVENTS. 4-1/2" AND 6" LONG WOODEN STICKS MIX OR SPREAD JUST ABOUT ANYTHING IN A SHOP. LONGER STICKS WORK GREAT WITH EPOXIES.
|
|
|
|
Adhesives - Water Based
|
J.E. MOSER'S CRITICAL BOND II WOOD GLUE
|
| Critical Bond Ii Wood Glue
...plus other(s)
|
J.E. MOSER'S® CRITICAL BOND II™ GAP FILLING GLUE IS A POLYVINYL ACETATE EMULSION ADHESIVE THAT CREATES A SUPER STRONG BOND FOR INTERIOR WOODWORK AND WORKS GREAT WITH ALMOST ANY SOFT WOOD AND HARDWOOD:
HIGH SOLIDS' CONTENT ENSURES SUPERIOR GAP FILLING, MANY TIMES ELIMINATING THE NEED FOR WOOD FILLER. NATURAL WOOD TONE COLOR HELPS GLUE JOINTS BLEND IN. NON-STAINING FORMULA HELPS PREVENT GLUE SPOTS ON YOUR WOOD, WHICH CAN CAUSE PROBLEMS WHEN APPLYING COLORED STAINS OR DYES. 10-20 MINUTE OPEN TIME; 30-90 MINUTE CLAMP TIME. NON-TOXIC AND NON-FLAMMABLE. WARM WATER CLEAN UP WHEN GLUE IS WET. CANADA.
|
|
|
|
Adhesives - Water Based
|
J.E. MOSER'S® OL'YELLER WOOD GLUE
|
| Ol'yeller Wood Glue Gal
...plus other(s)
|
OL' YELLER™ REGULAR COMPARES FAVORABLY WITH OTHER YELLOW GLUES IN PERFORMANCE - BUT COSTS A LOT LESS!
INDUSTRIAL GRADE ALIPHATIC PVA ADHESIVE FROM WOODWORKER'S SUPPLY® CREATES A BOND STRONGER THAN MOST WOOD SPECIES. TYPICAL BONDING APPLICATIONS INCLUDE CABINETS, FURNITURE, INTERIOR DOORS, TRIM, PLYWOOD, EDGE BONDING, PANEL-TO-FRAME, GENERAL WOOD ASSEMBLY AND COUNTERTOPS. RECOMMENDED FOR BONDING HIGH PRESSURE LAMINATE (HPL) TO WOOD OR WOOD-BASED SUBSTRATES. HARD BOND LINES HAVE GOOD SANDING PROPERTIES. NON-FLAMMABLE, NON-HAZARDOUS, NON-STAINING AND EASY TO CLEAN-UP WITH WATER WHILE WET. USA.
|
|
|
|
Adhesives - Water Based
|
J.E. MOSER'S® OL'YELLER WATERDOG WOOD GLUE
|
| Ol'yeller Waterdog Wood Glue Gal
...plus other(s)
|
OL' YELLER™ WATER DOG IS AN INDUSTRIAL, WATER RESISTANT TYPE II PVA GLUE THAT STANDS UP TO THE BEST GLUES ON THE MARKET IN SHEAR (BOND STRENGTH PSI) AND WOOD FAILURE RATE TESTS BUT COSTS LESS:
INDUSTRIAL GRADE CROSSLINKING ALIPHATIC ADHESIVE FROM WOODWORKER'S SUPPLY® COMBINES THE CONVENIENCE OF A READY-TO-USE GLUE. PROVIDES TYPE II WATER RESISTANCE AND CREATES A BOND STRONGER THAN MOST WOOD SPECIES. TYPICAL BONDING APPLICATIONS INCLUDE INTERIOR/EXTERIOR DOORS, TRIM, PLYWOOD, EDGEBONDING, PANEL-TO-FRAME, GENERAL WOOD ASSEMBLY AND COUNTERTOPS. RECOMMENDED FOR BONDING HIGH PRESSURE LAMINATE (HPL) TO WOOD OR WOOD-BASED SUBSTRATES. HARD BOND LINES HAVE GOOD SANDING PROPERTIES. NON-FLAMMABLE, NON-HAZARDOUS, NON-STAINING AND EASY TO CLEAN-UP WITH WATER WHILE WET. USA.
|
|
|
|
Advanced Search Tools
Browse
will
