|
|
|
Hardware Shelf And Support - Brackets
|
CREATE A WORK SURFACE THAT SIMPLY FOLDS OUT OF THE WAY FOR STORAGE
|
| 12" Folding Bracket
...plus other(s)
|
STURDY KNAPE & VOGT® FOLDING SHELF BRACKETS SUPPORT UP TO 750 LBS. PER PAIR WHEN PROPERLY INSTALLED:
BRACKETS LOCK AT 90°, 80° AND 70° FOR CONVENIENT VERSATILITY AND 0° FOR OUT-OF-THE-WAY STORAGE. PERFECT FOR LAUNDRY ROOMS, CRAFT AREAS, PLAYROOMS, BEDROOMS AND DRAWING TABLE APPLICATIONS. DURABLE ZINC-COATED STEEL WITH SPRING-LOADED RELEASE LEVER. NOTE: TO ACHIEVE 750 LBS. PER PAIR CAPACITY, MANUFACTURER RECOMMENDS INSTALLING EACH BRACKET WITH THREE #10 X 2" PAN HEAD SCREWS, FASTENED INTO 2 X 4 WOODEN WALL STUDS AT 16" ON CENTER.
|
|
|
|
Hardware Shelf And Support - Brackets
|
HEAVY DUTY WORK STATION BRACKETS PERFECT FOR WORKBENCHES, COMPUTERS AND MUCH MORE
|
| 12x18 Rev Brackets Black
...plus other(s)
|
HIGH QUALITY, CANTILEVER WORK STATION BRACKETS ARE FABRICATED FROM 1/8" STEEL WITH WHITE OR BLACK TEXTURED POWDER COAT FINISHES - EASILY CREATE STRONG WORK SURFACES WITHOUT CUMBERSOME LEGS TO GET IN THE WAY:
AVAILABLE IN FOUR SIZES; REVERSIBLE DESIGN MAKES THEM VERSATILE AND EASIER TO USE. 3" X 3" - 45° NOTCHES ALLOW FOR STANDARD WALL CLEATS AND WIRE RUNS. MULTIPLE 1/4" DIA. MOUNTING HOLES PER SIDE (MOUNTING HARDWARE NOT INCLUDED). PACKAGED IN EQUAL QUANTITIES OF "RIGHTS" AND "LEFTS". IMPORTED.
|
|
|
|
Hardware Shelf And Support - Brackets
|
EASY LEVELING SHELF AND COUNTER BRACKETS
|
| 8"x11" Easy Level Bracket-wh
...plus other(s)
|
UNLIKE CONVENTIONAL SHELF BRACKETS, PATENT PENDING EASY LEVELING SHELF AND COUNTER BRACKETS CAN BE ADJUSTED TO MAKE SHELVES, COUNTERTOPS OR WORKSTATIONS LEVEL - ONCE ALIGNED, TOP AND BOTTOM SECTIONS BOLT TOGETHER SECURELY:
TESTED TO SUPPORT UP TO 640 LBS. WHEN ATTACHED FIRMLY TO WOOD STUDS, 16" ON CENTER. 19", 21" AND 27" BRACKETS HAVE A 1-3/8" DIA. PUNCHED HOLE FOR ROUTING CABLES, WIRING OR AIR LINES. WORK WITH 3/4" X 1-1/2" OR 1-1/2" X 1-1/2" CLEATS. NO CROSS BRACE REQUIRED. EASY ACCESS TO WALL ANCHOR SCREWS. WHITE OR BLACK POWDER COATED STEEL - SURFACE CAN BE PAINTED TO MATCH DECOR. ANSI/BHMA TESTED. ASSEMBLY HARDWARE AND MOUNTING INSTRUCTIONS INCLUDED. IMPORTED.
|
|
|
|
Hardware Shelf And Support - Brackets
|
WOODTEK USA® SUPER HEAVY DUTY SHELF STANDARDS AND BRACKETS
|
| 24" Hd Shelf Standard
...plus other(s)
|
WOODTEK USA® SUPER HEAVY DUTY SHELVING STANDARDS AND BRACKETS ARE FORMED FROM 3/16" THICK, HEAVY GAUGE STEEL TO SAFELY HOLD HEAVY LOADS:
WHEN PROPERLY INSTALLED ONTO THE 24" LONG STANDARDS, 10" AND 18" BRACKETS CAN EACH SUPPORT UP TO 500 LBS., 1" FROM THE TIP. BLACK POWDER-COAT FINISH FOR DURABILITY. STANDARDS ARE PREDRILLED FOR 3/8" DIA. FASTENERS (FASTENERS NOT INCLUDED>). USA.
|
|
|
|
Hardware Shelf And Support - Brackets
|
KV 187LL SHELF BRACKET WITH LOCK
|
| 12" Kv187ll Shelf Bracket-ano
|
|
|
|
Hardware Shelf And Support - Brackets
|
KNAPE & VOGT® 71/170 STANDARDS AND BRACKETS FOR SPECIALTY APPLICATIONS
|
| 8" Kv170 Shelf Bracket
...plus other(s)
|
KNAPE & VOGT® KV71 ANOCHROME™ NARROW FACE SHELVING STANDARDS COME IN FOUR LENGTHS WITH A FINISH THAT RESISTS RUST AND OXIDATION:
DURABLE 16 GAUGE STEEL, 5/16"W X 13/32"H ( MOUNTING SCREWS NOT INCLUDED). COMPATIBLE WITH KV170 ANOCHROME™ BOLTLESS BRACKETS, WHICH FIT AND SNAP INTO STANDARDS. ALSO COMPATIBLE WITH KV80 STANDARDS.
|
|
|
|
Hardware Shelf And Support - Brackets
|
KNAPE & VOGT® KV144 ANOCHROME™ MIRROR STANDARDS SUPPORT BOTH MIRRORS AND SHELVES
|
| 48" Mirror Standard
...plus other(s)
|
DESIGNED FOR MIRRORED WALL SHELVING APPLICATIONS, KNAPE & VOGT® KV144 ANOCHROME™ MIRROR STANDARDS COME IN THREE LENGTHS OF DURABLE STEEL WITH A FINISH THAT RESISTS RUST AND OXIDATION:
1.13" FACE X 0.31" THICK; MIRRORS ARE HELD IN PLACE BY 0.25" OVERHANG ON EACH SIDE OF STANDARD - NOTCHES ACCOMMODATE SHELF BRACKETS (NOT INCLUDED). 48", 60" AND 72" LENGTHS (MOUNTING SCREWS NOT INCLUDED).
LIMITED TO QUANTITIES ON HAND
TO HELP COMPLETE YOUR PROJECT, MAY WE SUGGEST:
830-690 - KNAPE & VOGT® KV180 ANOCHROME™ SHELF BRACKETS.
|
|
|
|
Hardware Shelf And Support - Brackets
|
QUICKLY AND EASILY ELIMINATE ANNOYING SUB-FLOOR SAGS OR SEAMS
|
| Seam-ender
...plus other(s)
|
|
|
|
Hardware Shelf And Support - Brackets
|
SHELF BRACKETS THAT FOLD OUT OF THE WAY
|
| Folding Shelf Bracket-12"
...plus other(s)
|
GREAT ANYWHERE WHERE SHELVES NEED TO FOLD OUT OF THE WAY:
12" AND 8" STEEL BRACKETS AUTOMATICALLY LOCK INTO POSITION; LIFT THE SHELF AND THEY UNLOCK. GREY ENAMEL FINISH. SOLD IN PAIRS. USE #10 SCREWS (NOT INCLUDED).
|
|
|
|
Hardware Shelf And Support - Brackets
|
FOLDING SHELF BRACKETS HOLD UP TO 88 LBS. PER PAIR
|
| Folding Shelf Bracket
|
10" LONG FOLDING SHELF BRACKETS LOCK OPEN TO HOLD SHELVES UP TO 12" WIDE:
RELEASE BUTTON LETS SHELF FOLD DOWN AND OUT OF THE WAY WHEN NOT IN USE. YELLOW CHROMATE FINISH. MOUNT TO SHELVING WITH #8 SCREWS (NOT INCLUDED). SOLD IN PAIRS. IMPORTED
|
|
|
|
Hardware Shelf And Support - Pilasters & Standards
|
KNAPE & VOGT® SHELVING SYSTEM SUPPORTS UP TO 450 POUNDS
|
| 48" Kv82 Shelf Standard-black
...plus other(s)
|
THE KNAPE & VOGT® SERIES 82/182 SHELVING SYSTEM IS A GREAT CHOICE WHERE APPEARANCE AND STRENGTH ARE CRITICAL - IDEAL FOR SCHOOLS, HOSPITALS, OFFICES AND EVEN HOMES. SMOOTH, ROUNDED CORNERS GIVE A SOFTER AND LESS INTRUSIVE LOOK WHILE ALL-METAL, DUAL-TRACK STANDARDS AND "U"-SHAPED BRACKETS EASILY SUPPORT HEAVY LOADS - WHITE OR BLACK EPOXY FINISHES:
KV® 82 STANDARDS ARE 1.05" WIDE, PROJECT 0.69" AND ARE AVAILABLE IN 48", 72" AND 96" LENGTHS. UNIQUE COVER STRIPS PROVIDE A CLEAN AND APPEALING APPEARANCE. KV® 182 BRACKETS ARE 0.53" WIDE AND FASTEN ONTO STANDARDS USING LUGS. 5" LONG BRACKETS SUPPORT 425 LBS., 7" - 360 LBS., 9" - 370 LBS., 10-1/2" - 330 LBS., 12-1/2" - 300 LBS., 14-1/2" - 450 LBS., 18-1/2" - 400 LBS., 22-1/2" - 400 LBS. BOOKENDS SNAP-FIT INTO STANDARDS. 7" LONG UNIT IS 4-1/2" HIGH; 9" AND 10-1/2" ARE 5-3/4" HIGH. SHELF LOCATORS/JOINERS MOUNT ONTO SHELF BOTTOM TO STABILIZE SHELF ON BRACKETS, WHILE ALLOWING EASY REMOVAL (4 LOCATORS/JOINERS AND 8 SCREWS). WALL STANDARD SCREWS FASTEN STANDARDS ONTO WALLS (6, 2" LONG FLAT HEAD SCREWS, 6 WALL ANCHORS, 6 COVER TABS). SHELF BRACKET SCREWS ANCHOR SHELVES DIRECTLY ONTO BRACKETS (6, EACH, 1", 2" AND 3-1/8" LONG OVAL HEAD TAPPING SCREWS). NOTE: STANDARDS, BRACKETS, BOOKENDS AND HARDWARE SOLD SEPARATELY - SHELVES NOT INCLUDED. ALSO AVAILABLE IN BLACK OR WHITE, DISCONTINUED, TWIN-SLOT KNAPE & VOGT® SERIES E3200 HEAVY-DUTY SHELVING STANDARDS CAN BE INSTALLED USING 182 BRACKETS AND MOUNTING HARDWARE (NOT INCLUDED) - LIMITED TO QUANTITIES ON HAND. LIFETIME MANUFACTURER'S WARRANTY. USA.
|
|
|
|
Hardware Shelf And Support - Pilasters & Standards
|
THIN PROFILE ALUMINUM SHELF STANDARD GIVES A CLEAN FINISHED LOOK TO SHELVING
|
| 1820mm Low Profile Surf Mount Standard
...plus other(s)
|
LOW PROFILE ALUMINUM SHELF STANDARDS UPGRADE THE LOOK OF ADJUSTABLE SHELVING:
THE SURFACE MOUNT VERSION OF THESE 1820MM (71-21/32") LONG THIN PROFILE ALUMINUM SHELF STANDARDS IS ONLY 3MM (1/8") THICK AND 10MM WIDE. STANDARDS FASTEN TO UPRIGHT SURFACE WITH COLOR COORDINATED MOUNTING SCREWS FOR A VERY CLEAN LOOK. SCREW HOLES ARE LOCATED EVERY 120MM (4-47/64") GIVING 16 SCREW HOLES PER STANDARD. SHELF SUPPORTS FIT INTO SPECIALLY FORMED OPENINGS WHICH KEEP THE SUPPORTS FROM FALLING OUT OF THE STANDARDS. SHELF SUPPORTS ARE MADE FROM 430 STAINLESS STEEL AND HAVE A VERY THIN PROFILE WHICH ELIMINATES DEAD SPACE AT THE BOTTOM OF THE BRACKET. THE BRACKETS MEASURE 20MM X 20MM X 10MM WIDE (51/64" X 51/64" X 3/8") A RUBBER CAP IS AVAILABLE FOR THE SHELF SUPPORTS THAT CUSHIONS GLASS SHELVING OR CAN BE USED TO SECURE WOODEN SHELVES. THE RUBBER CAP CAN BE MOUNTED WITH EITHER THE FLAT OR RAISED PORTION UP. OPTIONAL GREY ABS END CAPS SCREW ON TO COVER THE OPEN ENDS OF THE STANDARDS. THE 1820MM MORTISE IN VERSION OF THE SHELF STANDARDS MOUNTS INTO A 10MM WIDE X 6MM DEEP RABBET. THIS STANDARD HAS A 12MM WIDE FACE WHICH GIVES A CLEAN TRIMMED APPEARANCE WHEN MOUNTED. FIT TIGHTNESS MAY VARY DEPENDING ON THE MATERIAL INTO WHICH IT IS MOUNTED - WOOD GLUE CAN BE APPLIED TO THE RIBBED EDGES FOR A MORE SECURE MOUNT. 3MM X 16MM MOUNTING SCREWS ARE PACKED 100 PER BOX. JAPAN
|
|
|
|
Hardware Shelf And Support - Pilasters & Standards
|
COVERED SHELF SUPPORTS
|
| 1820mm Covered Shelf Standard-s/s
...plus other(s)
|
LOW PROFILE STAINLESS STEEL SHELF SUPPORTS SHOW NO MOUNTING SCREWS AND NO ADJUSTMENT SLOTS WHEN OPTIONAL COVER STRIPS ARE IN PLACE. LOW PROFILE 1820MM (71-21/32") STAINLESS STEEL SHELF SUPPORTS SHOW NO MOUNTING SCREWS AND NO ADJUSTMENT SLOTS WHEN OPTIONAL COVER STRIPS ARE IN PLACE:
MADE FROM SATIN FINISHED 430 STAINLESS STEEL FOR DURABILITY, THESE SUPPORTS ARE FORMED WITH CLIP MOUNTING SLOTS SPACED 15MM APART ALONG THE LENGTH OF THE STANDARD. THE TWO PIECE SHELF CLIPS HAVE A STAINLESS STEEL FRAME AND A SOFT PLASTIC (ELASTOMER) INSERT TO HOLD THE SHAPE AND CREATE A SECURE FIT INTO THE SIDE CHANNELS OF THE STANDARDS. TO INSTALL THE CLIPS, REMOVE THE PLASTIC INSERT, SQUEEZE THE CLIP FRAME AND INSERT INTO THE STANDARD; REINSERTING THE PLASTIC INSERT LOCKS THE SHELF CLIP IN PLACE. SHELF CLIPS ARE AVAILABLE WITH EITHER WHITE OR BROWN PLASTIC (ELASTOMER) INSERTS. STANDARDS CAN BE FASTENED TO UPRIGHT SURFACES USING #5X1/2" OR #5X3/4" FLAT HEAD WOOD SCREWS. (EACH STANDARD HAS 11 COUNTERSUNK SCREW HOLES.) WHITE OR BROWN OVER STRIPS ARE 1820MM (71-21/32") PVC PLASTIC AND PRESS FIT INTO THE STANDARDS FTO CONCEAL THE MOUNTING SCREWS. SCREW-ON POLYPROPYLENE END CAPS HAVE A HINGED FLAP THAT HIDES THE MOUNTING SCREW. ALL COMPONENTS ARE SOLD EACH. JAPAN. TO HELP COMPLETE YOUR PROJECT, MAY WE SUGGEST:
#5 X 1/2" FH SCREWS - 800-525. #5 X 3/4" FH SCREWS - 800-526.
|
|
|
|
Hardware Shelf And Support - Pilasters & Standards
|
ADJUSTABLE, DURABLE KNAPE & VOGT® KV180 SHELVING BRACKETS DESIGNED FOR KV80 STANDARDS
|
| 36" Kv80 Anochrome Shelf Standard
...plus other(s)
|
KNAPE & VOGT® 16 GAUGE STEEL KV180 SHELF BRACKETS ARE AVAILABLE IN ELECTROPLATED ANOCHROME™ OR POWDER COATED BLACK OR WHITE FINISHES:
AVAILABLE IN 8" TO 20" LENGTHS - ADJUSTABLE ON 1" CENTERS. DESIGNED TO FIT AND SNAP INTO KV80 SHELF STANDARDS (ORDER SEPARATELY) FOR SECURE SUPPORT. USA.
|
|
|
|
Hardware Shelf And Support - Pilasters & Standards
|
KNAPE & VOGT® 83/183 OVERSIZE STANDARDS AND FLANGED BRACKETS FOR LONG RUNS OF SHELVING
|
| 48" Kv83 Shelf Standard-ano
...plus other(s)
|
DESIGNED FOR EXTRA-LONG APPLICATIONS, KNAPE & VOGT® KV83 OVERSIZE SHELVING STANDARDS AND BRACKETS COME IN FIVE LENGTHS WITH A FINISH THAT RESISTS RUST AND OXIDATION:
KV83 STANDARDS ARE MADE FROM 16GA STEEL, 3/4" WIDE X 1/2" HIGH - COMPATIBLE WITH ALL KV® SHELF BRACKETS FOR USE IN 1" ADJUSTMENT STANDARDS. BRACKETS ARE AVAILABLE IN CENTER (FLANGED BOTH SIDES) AND STYLES FOR LEFT- OR RIGHT-HAND SHELF ENDS. KV183 BRACKETS HAVE A WIDE FLANGE TO ALLOW BETTER FASTENING OF SHELF MATERIAL TO BRACKETS. ANOCHROME™ ELECTROPLATED FINISH.
|
|
|
|
Hardware Shelf And Support - Pilasters & Standards
|
KNAPE & VOGT® 87/186/187 STANDARDS AND BRACKETS LOCK TOGETHER FOR ADDED SECURITY
|
| 36" Kv87 Anochrome Shelf Standard
...plus other(s)
|
IDEAL FOR WORKSHOPS AND LIGHT INDUSTRIAL APPLICATIONS, KNAPE & VOGT® HEAVY DUTY SHELVING STANDARDS AND BRACKETS COME IN SIZES TO MEET MOST STORAGE REQUIREMENT AND ARE AVAILABLE WITH A WHITE POWDER COAT OR ANOCHROME™ FINISH:
KV87 STANDARDS ARE 12GA STEEL, 7/8" WIDE X 11/16" HIGH AND FEATURE 2" ADJUSTMENT INCREMENTS - 24", 36", 48", 60", 72", 84" AND 96" LENGTHS. KV186LL BRACKETS ARE 12GA STEEL, 4-5/16" HIGH AND WILL ACCOMMODATE SHELF DEPTHS OF 8" AND 10". KV187LL BRACKETS ARE 12GA STEEL, 5-1/16" HIGH FOR SHELF DEPTHS OF 12" 14", 16" AND 18"; 6-1/2" HIGH FOR SHELF DEPTHS OF 20", 22" AND 24". BOTH BRACKET STYLES FEATURE AN INJECTION-MOLDED RESIN LOCKING LEVER TO SECURE THE BRACKETS TO THE STANDARDS.
|
|
|
|
Hardware Shelf And Support - Pilasters & Standards
|
KNAPE & VOGT® 85/185 ANOCHROME™ STANDARDS AND BRACKETS SUPPORT LONG RUNS OF SHELVING
|
| 84" Kv85 Shelf Standard-ano
...plus other(s)
|
FOR USE ANYWHERE STRONG SHELVING IS NEEDED, KNAPE & VOGT® KV85 ANOCHROME™ DOUBLE SLOT SHELVING STANDARDS COME WITH A FINISH THAT RESISTS RUST AND OXIDATION:
DURABLE 16GA STEEL, 1/2"H X 1-1/4"W WITH 1" HEIGHT ADJUSTMENT (#10 FLATHEAD MOUNTING SCREWS NOT INCLUDED). COMPATIBLE WITH KV185 ANOCHROME™ DOUBLE SLOT SHELVING BRACKETS, WHICH SNAP INTO STANDARDS. BRACKETS HAVE HOLES IN CROSS MEMBERS FOR ATTACHING TO SHELF. 8", 10" AND 12" BRACKETS ARE 16GA STEEL; 16" TO 24" ARE 14GA.
|
|
|
|
Hardware Shelf And Support - Pilasters & Standards
|
KNAPE & VOGT® KV71 ANOCHROME™ NARROW FACE SHELVING STANDARDS IDEAL FOR SPECIAL EFFECTS AND CUSTOM FIXTURE DESIGN
|
| 48" Kv71 Shelf Standard
...plus other(s)
|
DESIGNED FOR SPECIALITY APPLICATIONS, KNAPE & VOGT® KV71 ANOCHROME™ NARROW FACE SHELVING STANDARDS COME IN FOUR LENGTHS WITH A FINISH THAT RESISTS RUST AND OXIDATION:
DURABLE 16 GAUGE STEEL, 5/16"W X 13/32"H. 48", 60", 72" AND 96" LENGTHS ( MOUNTING SCREWS NOT INCLUDED).
COMPATIBLE WITH KNAPE & VOGT® KV170 ANOCHROME™ BOLTLESS SHELVING BRACKETS, WHICH FIT AND SNAP INTO STANDARDS: 8", 10", 12", 14" AND 16".
|
|
|
|
Hardware Shelf And Support - Pilasters & Standards
|
KV® 80/180 STANDARDS AND BRACKETS CREATE STRONG, DURABLE SHELVING
|
| 80br 48"brass Pl.standard
...plus other(s)
|
KNAPE & VOGT® KV80 SHELF STANDARDS MEASURE 5/8" WIDE X 13/32" HIGH AND CAN BE MOUNTED ONTO NEARLY ANY TYPE OF WALL:
REINFORCED KV180 SHELF BRACKETS LOCK INTO SLOTTED STANDARDS FOR SECURE, WEIGHT-BEARING SUPPORT. FULLY ADJUSTABLE IN 1" INCREMENTS - BOTH ARE MADE FROM 16GA STEEL. AVAILABLE IN ELECTROPLATED ANOCHROME™ OR BLACK OR WHITE POWDER-COATED FINISHES.
|
|
|
|
Hardware Shelf And Support - Shelf Pins
|
KV® 208 SERIES HEAVY DUTY SHELF BRACKETS 21-1/2"
|
| Hardware For Kv Bracket
...plus other(s)
|
KNAPE & VOGT® SERIES 208™ SHELF BRACKETS ARE MADE FROM 5MM THICK X 1-3/16" WIDE STEEL AND INCLUDE A 3/4" WIDE SWAGGED STRUT:
WILL SUPPORT 1,000 LBS. PER PAIR WHEN INSTALLED ACCORDING TO MANUFACTURER'S INSTRUCTIONS. FOUR SIZES IN BLACK, WHITE OR TITANIUM TONED EPOXY COATING. BRACKETS SOLD INDIVIDUALLY. OPTIONAL FASTENER PACKAGE INCLUDES THREE, EACH, 5/16" X 3" LAG SCREWS, 5/16" FLAT WASHERS AND #8 X 5/8" WOOD SCREWS.
|
|
|
|
Advanced Search Tools
Browse
to see Sub Categories)
