|
|
|
Hand Tools - Carving Tools
|
JERRY-RIG™ WORK POSITIONER HOLDS PROJECTS TIGHT AND AT JUST THE RIGHT CARVING ANGLE
|
| Jerry-rig W/table Clamp & Hde
...plus other(s)
|
EXTREMELY RUGGED AND IMPRESSIVELY VERSATILE, JERRY-RIG™ JR-100 UNIVERSAL 360° WORK POSITIONER SECURELY HOLDS STOCK, MODELS OR SMALL PARTS - VERTICALLY OR HORIZONTALLY - WHEN CARVING, PAINTING, TEXTURING, GLUING OR SCULPTING:
CLAMPING HEAD, WITH PADDED INDEXED LOCKING HANDLE, ALLOWS 360° SIDE-TO-SIDE ROTATION AND 12 FRONT-TO-BACK POSITIONS FOR POSITIONER PLATES, WORK HOLDERS AND OTHER FIXTURES. MOUNT HORIZONTALLY OR VERTICALLY FOR WORK ABOVE OR BELOW WORK SURFACE - ACCOMMODATES ALL PANAVISE® HOLDING FIXTURES. TABLE CLAMP ATTACHES TO WORK BENCHES UP TO 3" THICK OR IS REMOVABLE TO ALLOW BENCH MOUNTING. CUSHIONED HANDGRIP FOR EASIER TIGHTENING, KNURLED PAD FOR BETTER GRIPPING AND A RUBBER BUMPER INSIDE THE CLAMP FACE TO PREVENT SKEWING. JERRY-RIG™ JR-100LC WORK POSITIONER (TABLE CLAMP AND HARDWARE KIT NOT INCLUDED) - WOODTURNERS WANTING TO TAKE ADVANTAGE OF JERRY-RIG™ VERSATILITY CAN EITHER USE AN EXISTING CLAMP HEAD OR PURCHASE A HEAD WITHOUT THE TABLE CLAMP: THEN, SIMPLY TIGHTEN AN OPTIONAL CARVING POST INTO THE HEAD, ADJUST FOR HEIGHT, THREAD THE FACEPLATE OR CHUCK ONTO THE CARVING POST AND BEGIN WORK - THERE IS NO NEED TO REMOVE THE WORK FROM THE FACEPLACE OR CHUCK. HEAVY, CAST ALUMINUM WITH BLUE EPOXY FINISH. 3-1/2" X 4-1/2" X 5/8" POSITIONER PLATE WITH MOUNTING ROD INCLUDED. JERRY-RIG™ JR-B4 BALL POSITIONER IS AN ALL STEEL ERGONOMIC WORK POSITIONER WITH A SINGLE LEVER TO EASILY TILT, TURN AND ROTATE YOUR WORK TO THE MOST COMFORTABLE POSITION. 2.5 INCH DIAMETER STEEL BALL WITH LOCKING HANDLE AND TEE SHAFT. BASE IS 3 INCHES SQUARE. CAN FIT INTO YOUR WORK BENCH VISE OR BE MOUNTED ONTO A WORKBENCH. JERRY-RIG™ JR-B4LC BALL POSITIONER DOES NOT INCLUDE CLAMP AND HARDWARE. IT CAN BE PERMANENTLY ATTACHED ONTO YOUR WORKBENCH.
A WIDE RANGE OF ACCESSORIES IS AVAILABLE TO MAKE FULL USE OF JERRY-RIG™ CAPABILITIES: JR-HW HARDWARE KIT MOUNTS ONTO THE BASE OF A CARVING, ALLOWING IT TO BE QUICKLY SLID OFF AND ONTO THE STANDARD POSITIONER PLATE. JR-DH1 J-RIG MOUNTING KIT PLACED THROUGH THE BENCH TOP AND INTO THE BASE OF THE RIG MAKES FOR A ROTATING BENCH MOUNT WITHOUT THE CLAMP. JR-P1 STANDARD 3-1/2" X 4-1/2" X 5/8" POSITIONER PLATE WITH MOUNTING ROD. JR-PM MEDIUM 3-5/8" X 1-1/4" X 5/8" POSITIONER PLATE WITH MOUNTING ROD. JR-PS-2 SMALL 2-1/8" X 3/4" X 1/4" POSITIONER PLATE WITH MOUNTING ROD. JR-G1 GRIP-ALL HOLDER ATTACHES TO CARVINGS USING BUILT-IN SPIKES AND #7 X 3-1/2" WOOD SCREW - 3-1/2"L X 5/8" DIA. HARDENED STEEL HEXAGONAL SHAFT HOLDS UP TO 5" CUBES, FITS INTO CLAMPING HEAD OR CAN BE HAND HELD. JR-G2, SIMILAR TO GRIP-ALL HOLDER, 3-1/2"L X 9/16" DIA. GRIP-STICK HOLDER HAS 1/2"L #10 WOOD SCREW TIP ON ONE END - IDEAL FOR SMALL CARVINGS, PAINTING AND DETAILING. JR-PW J-RIG LARGE CARVING SCREW FITS INTO CLAMP HEAD FOR SUPPORTING LARGE CARVINGS. JR-V2 TWO JAW VISE ATTACHMENT PLACES A FIRM GRIP ON IRREGULAR OBJECTS - JR-PP1 PEG PLATES CAN BE ATTACHED TO THE VISE FOR ARCHITECTURAL CARVING. JR-CSL 9" TAPERED CARVING SCREW HOLDS MORE TIGHTLY THAN STRAIGHT SCREWS. IF IT LOOSENS, IT CAN BE RETIGHTENED; NO NEED TO DRILL A HOLE DEEPER OR A NEW HOLE. "T" HANDLE. JR-CSM 6-3/4" TAPERED CARVING SCREW IS DESIGNED FOR SMALLER CARVINGS. JRCP-1 - 1" X 8 TPI CARVING POST. JRCP-1.25 - 1-1/4" X 8 TPI CARVING POST. JRCP-1.5 - 1-1/2" X 8 TPI CARVING POST. USA.
|
|
|
|
Hand Tools - Carving Tools
|
START OUT RIGHT WITH THIS SIX PIECE WOODCARVING SET
|
| 6 Pc Woodcarving Set
|
IDEAL FOR BEGINNERS, THE 7" LONG TOOLS IN THIS CROWN SIX PIECE WOODCARVING SET FEATURE HIGH QUALITY, HARDENED AND TEMPERED CARBON STEEL BLADES FITTED TO STAINED BEECH HANDLES:
SET INCLUDES 5/16" SQUARE CHISEL, 5/16" BENT SQUARE CHISEL, 5/16" SKEW CHISEL, 3/16" STRAIGHT GOUGE, 5/16" BENT GOUGE AND A 3/16" BENT V-TOOL. ENGLAND.
|
|
|
|
Hand Tools - Carving Tools
|
FLEXCUT® WOODCARVING TOOLS - NEW TOOLS FOR AN OLD CRAFT
|
| 5 Piece Craft Carver Kit
...plus other(s)
|
FLEXCUT® WOODCARVING TOOLS ARE THE CHOICE OF SERIOUS AMATEUR AND PROFESSIONAL WOODTURNERS, WOOD CARVERS, WOOD SCULPTORS, WOODEN BLOCK PRINTMAKERS AND COMMERCIAL SIGN SHOPS:
117-602 - 5 PIECE CRAFT CARVER SET COMES WITH QUICK CONNECT ABS HANDLE AND 4 INTERCHANGEABLE BLADES (#3 X 3/8", #6 X 5/16", #11 X 1/8", 70° X 1/4"). ALL STORE IN A 10 POCKET TOOL ROLL THAT FOLDS DOWN TO 5" X 2". 117-605 - 11 PIECE CRAFT CARVER SET IS SIMILAR BUT HAS 6 ADDITIONAL INTERCHANGEABLE BLADES (#1 X 1/4", #3 X 5/8", #5 X 9/16", #9 X 1.5MM, #11 X 1/4", 45° X 1MM). BOTH SETS COME WITH BEGINNING CARVING BLANK, INSTRUCTIONS AND SHARPENING MANUALS.
PALM TOOLS ARE DESIGNED FOR PIECES THAT ARE DIFFICULT TO CLAMP INTO A VISE:
117-611 - 5 PIECE REGULAR PALM SET INCLUDES #2 X 5/16", #3 X 3/8", #6 X 5/16", #11 X 1/8", 70° X 1/4" BLADES. 117-614 - 9 PIECE DELUXE PALM SET ALSO INCLUDES #3 X 5/8", #5 X 9/16", #8 X 11/16", 70° X 3/8" BLADES. 117-764 - METRIC BASED MICRO-PALM SET HAS #5 X 2.5MM, #9 X 1MM, #9 X 1.5MM, 45° X 1 MM BLADES. 117-767 - SUPER-WIDE FORMAT PALM SET INCLUDES #3 X 7/8", #6 X 13/16", #8 X 11/16", #9 X 9/16" BLADES. ALL PALM TOOLS ARE 5" LONG WITH FIXED WOODEN HANDLES.
FLEXCUT® ALSO OFFERS A WIDE VARIETY OF INDIVIDUAL KNIVES, GOUGES AND ACCESSORIES:
THE DETAIL KNIFE (117-617), CURVED EDGE MINI-PELICAN KNIFE (117-620), 5" FLEXIBLE DRAW KNIFE (117-623) AND CUTTING KNIFE (117-626) ALL HAVE CURVED WOODEN HANDLES TO MINIMIZE FATIGUE. SCORPS ARE RIGHT-ANGLED GOUGES DESIGNED FOR CARVING AREAS WHERE THE FULL LENGTH OF A GOUGE WILL NOT FIT; AVAILABLE IN RIGHT AND LEFT HANDED MODELS. TO MAINTAIN TOOL SHARPNESS, FLEXCUT® OFFERS SLIPSTROP™ (117-665), SPECIALLY MOLDED TO ALLOW FOR POLISHING AND DEBURRING V-TOOLS, GOUGES AND OUTSIDE EDGE BEVELS. 117-677 - FLEXCUT GOLD™ POLISHING COMPOUND IS INCLUDED WITH SLIPSTROP™ TO SPEED SHARPENING; ALSO AVAILABLE SEPARATELY.
LIMITED TO QUANTITIES ON HAND
|
|
|
|
Hand Tools - Carving Tools
|
FLEXCUT™ MALLET TOOLS - THE EXTRA EDGE FOR THE SERIOUS WOODCARVER
|
| #1x1/2" Chisel-single Bevel
...plus other(s)
|
CARVING LARGE PROJECTS OR DENSER HARDWOODS OFTEN REQUIRES MORE THAN JUST A HAND HELD TOOL.
FLEXCUT™ MALLET TOOLS ARE DESIGNED WITH JUST THAT IN MIND. HANDCRAFTED WITH A LONG-LASTING RAZOR EDGE, THE ASH HANDLES ON THESE TOOLS CAN BE DRIVEN WITH A MALLET WHEN A PROJECT REQUIRES EXTRA CUTTING CAPABILITIES. AVAILABLE IN COST-SAVING SETS OR INDIVIDUALLY:
118-904 - 10 PIECE DELUXE MALLET TOOL SET INCLUDES GOUGES FOR DETAILING TO HOGGING OFF LARGE AMOUNTS OF WASTE WOOD. (1/2" #3 GOUGE, 1" #3 GOUGE, 3/4" #5 GOUGE, 1-1/4" #5 GOUGE, 1/2" #9 GOUGE, 3/4" #10 GOUGE, 1/8" #11 GOUGE, 1/4" #11 GOUGE, 1/2" 60° V-PARTING TOOL AND 3/16" 45° V-PARTING TOOL.)118-907 - 6 PIECE STARTER MALLET TOOL SET PROVIDES AN EXCELLENT SAMPLING OF TOOLS TO GET THE BEGINNER STARTED ON SIMPLER PROJECTS. (1" #3 GOUGE, 3/4" #5 GOUGE, 7/16" #8 GOUGE, 1/4" #11 GOUGE, 1/2" #11 GOUGE AND 5/16" 60° V-PARTING TOOL.)118-910 - 4 PIECE SCULPTURE MALLET TOOL SET IS SIZED FOR VERY LARGE STOCK REMOVAL. HANDLE DIAMETERS AND STEEL CALIPERS ARE 20% LARGER. DESIGNED FOR CAROUSEL CARVERS, CHAINSAW CARVERS AND THOSE DOING LIFE SIZE STATUARY. (2" #3 GOUGE, 1-3/8" #5 GOUGE, 1-1/8" #11 GOUGE AND 1-3/8" 90° V-PARTING TOOL.)
LIMITED TO QUANTITIES ON HAND
|
|
|
|
Hand Tools - Carving Tools
|
THESE QUALITY WOODCARVING GOUGES ARE AMONG THE FINEST ON THE MARKET
|
| 6-pc Basic Palm Gouge Set
...plus other(s)
|
DESIGNED FOR INTRICATE HAND CARVING, 5" LONG STUBAI 57 SERIES PALM GOUGES FEATURE HARDWOOD HANDLES, LIFETIME GUARANTEES AND ARE HAND FORGED SO EDGES STAY SHARPER AND LAST LONGER:
6 PIECE BASIC SET INCLUDES A SKEW CHISEL, FOUR GOUGES AND A V-TOOL. 12 PIECE INTERMEDIATE SET CONTAINS TWO CHISELS, EIGHT GOUGES, TWO V-TOOLS AND A DURABLE CLOTH TOOL ROLL. 18 PIECE ADVANCED SET INCLUDES THREE CHISELS, 12 GOUGES, THREE V-TOOLS AND TOOL ROLL. AUSTRIA; TOOL ROLLS MADE IN USA.
|
|
|
|
Hand Tools - Carving Tools
|
SOLINGEN WOODCARVING SETS BUILT TO HIGH EUROPEAN STANDARDS
|
| Carving Set In Pouch
...plus other(s)
|
EITHER OF THESE SOLINGEN CARVING SETS WILL BE APPRECIATED BY THE PROFESSIONAL AS WELL AS THE SERIOUS AMATEUR WOODCARVER. BOTH FEATURE HIGH QUALITY STEEL BLADES AND SOLID WOOD HANDLES:
SEVEN PIECE SET COMES IN A PLASTIC POUCH AND INCLUDES BENT, DETAIL AND UNDERCUT CARVING KNIVES, 8MM STRAIGHT CHISEL, 7MM V-GOUGE, 6MM DEEP GOUGE AND A SHARPENING STONE. SIX PIECE SET INCLUDES STRAIGHT AND DOUBLE CUT KNIVES, 8MM SHALLOW GOUGE, 8MM STRAIGHT CHISEL, 7MM V-GOUGE AND 6MM DEEP GOUGE. GERMANY.
LIMITED TO QUANTITIES ON HAND NOTE: ENGLISH CONVERSIONS ARE APPROXIMATE: 6MM = 15/64". 7MM = 17/64". 8MM = 5/16". 10MM = 25/64". 12MM = 15/32".
|
|
|
|
Hand Tools - Carving Tools
|
YOU CAN REALLY CUT WITH HIGH QUALITY SOLINGEN CHIP CARVING KNIVES
|
| Straight Chip Carving Knife
...plus other(s)
|
NINE DIFFERENT SHAPES OF SOLINGEN CHIP CARVING KNIVES OFFER TREMENDOUS VERSATILITY - ALL FEATURE STRONG WOOD HANDLES AND SOLINGEN STEEL BLADES:
GREAT FOR CHIP CARVING AND GENERAL WHITTLING. 863-330 - #60 BENT KNIFE; 1-1/2" CUTTING EDGE, 3-1/2" HANDLE. 829-085 - #58 STRAIGHT KNIFE; 1-1/2" CUTTING EDGE, 5" HANDLE. 950-161 (NOT SHOWN) - #59 STRAIGHT KNIFE, SIMILAR TO #58; 1-3/8" CUTTING EDGE, 5-3/8" HANDLE - LIMITED TO QUANTITIES ON HAND. 829-078 - #52 BENT KNIFE; 1-1/8" CUTTING EDGE, 4-1/4" HANDLE. 863-309 - #51 UNDERCUT KNIFE; 1/2" CUTTING EDGE, 4-1/4" HANDLE. 863-316 - #54 SKEW KNIFE; 1" CUTTING EDGE, 4-1/4" HANDLE. 863-323 - #56 DETAIL KNIFE; 3/8" CUTTING EDGE, 3-1/2" HANDLE. 863-337 - #61 DOUBLE CUT SKEW KNIFE; 5/8" CUTTING EDGE, 4-1/4" HANDLE. 829-071 - #53 DOUBLE CUT CHIP KNIFE; 1-3/4" CUTTING EDGE, 4-1/4" HANDLE. 863-342 - #62 STRAIGHT KNIFE; 1-1/2" CUTTING EDGE, 3-1/2" HANDLE. 881-030 - 5 PIECE SET INCLUDES #51, #52, #53, #56 AND #58. GERMANY.
LIMITED TO QUANTITIES ON HAND
|
|
|
|
Hand Tools - Carving Tools
|
BENT SPOON AND GOUGE CARVING TOOLS
|
| 8mm Short Bent Spoon
...plus other(s)
|
LONG AND SHORT BENT SPOONS AND DEEP BENT GOUGES ARE GREAT FOR BAS-RELIEF, BOWL AND THREE DIMENSIONAL CARVING:
HIGH QUALITY SOLINGEN STEEL BLADES WITH COMFORTABLE AND DURABLE OCTAGONAL BOXWOOD HANDLE; 8" LONG. HONE BEFORE USE. GERMANY.
NOTE: ENGLISH CONVERSIONS ARE APPROXIMATE: 6MM = 15/64". 8MM = 5/16".
|
|
|
|
Hand Tools - Carving Tools
|
EIGHT PIECE CARVING SET CHISELS, GOUGES AND SPOONS DISPLAY EUROPEAN QUALITY
|
| Deep Gouge 10mm
...plus other(s)
|
WHEN YOU NEED CARVING TOOLS, CONSIDER THESE THAT FEATURE HIGH QUALITY SOLINGEN STEEL BLADES WITH COMFORTABLE AND DURABLE OCTAGONAL BOXWOOD HANDLES:
863-468 - EIGHT PIECE SET INCLUDES 6MM SHALLOW GOUGE (#6 SWEEP), 3MM AND 5MM V-GOUGES (#39 SWEEP), 2MM AND 6MM DEEP GOUGES (#10 SWEEP), 8MM LONG AND SHORT BENT SPOONS AND 4MM SKEW CHISEL (#2 SWEEP); 8" LONG. INDIVIDUAL CHISELS AND GOUGES AVAILABLE IN SIZES TO MEET ALMOST ANY CARVING REQUIREMENT. HONE BEFORE USE. GERMANY.
NOTE: ENGLISH CONVERSIONS ARE APPROXIMATE: 2MM = 5/64". 3MM = 7/64". 4MM = 5/32". 5MM = 13/64". 6MM = 15/64". 7MM = 17/64". 8MM = 5/16". 10MM = 25/64". 12MM = 15/32". 14MM = 35/64".
|
|
|
|
Hand Tools - Carving Tools
|
SUPERBLY BALANCED CARVING KNIVES FROM KEN HELVIE
|
| Detail Carving Knife
...plus other(s)
|
SUPERBLY BALANCED CARVING KNIVES HAVE POLISHED TUNGSTEN AND CARBON BLADES, TAPERED TO A FINE POINT FOR INTRICATE DETAIL CARVING:
878-421 - DETAIL KNIFE HAS 1-3/16"L BLADE; 6-1/4" OVERALL. 878-428 - ROUGH OUT KNIFE HAS 2"L BLADE; 7" OVERALL. 878-435 - JUMBO KNIFE HAS 2-1/4"L BLADE; 7-1/4" OVERALL. PAKKA HARDWOOD VENEER HANDLES ARE DYED, PRESSED WITH EPOXY AND SHAPED (HANDLE COLORS WILL VARY). EACH KNIFE COMES WITH A LEATHER SHEATH. USA.
|
|
|
|
Hand Tools - Carving Tools
|
SIX PIECE PALM GOUGE CARVING SET FOR EXTREMELY PRECISE WORK
|
| Subminiature Palm Gouge Set
...plus other(s)
|
HAND FORGED AND TEMPERED HIGH GRADE TOOL STEEL, THIS SIX PIECE SUB-MINIATURE PALM GOUGE SET WILL EXCEED YOUR CARVING REQUIREMENTS:
CUTTING EDGES ARE POLISHED, SHARPENED AND READY TO USE. HANDLES ARE LACQUERED HARDWOOD. 4-1/8" OVERALL LENGTH. IMPORTED.
|
|
|
|
Hand Tools - Carving Tools
|
QUALITY MOOR CHIP CARVING KNIFE AT AN AFFORDABLE PRICE
|
| Large Cutting Knife
...plus other(s)
|
THE FINEST STEEL, HARDENED TO RC60, IS USED TO MAKE MOOR CHIP CARVING KNIFE BLADES SO THEY CAN HOLD A KEEN EDGE FOR A LONGER TIME - BLADES ARE ANGLED 20° TO THE HANDLE TO SIGNIFICANTLY REDUCE CUTTING FRICTION AND MAKE IT EASIER TO CUT SHARP CURVES:
909-479 - SMALL KNIFE IS PERFECT FOR DETAIL WORK AND THOSE WITH SMALLER HANDS. 909-472 - LARGE KNIFE IS SUITABLE FOR ALMOST ALL CUTS - A DECREASING RADIUS NEAR THE POINT PUTS LESS METAL INTO THE WOOD FOR LESS FRICTION AND EASIER CUTTING. 909-486 - STABBING KNIFE IS IDEAL FOR ADDING DECORATIVE ACCENTS. LARGE AND STABBING KNIVES ARE APPROXIMATELY 5-" LONG - SMALL CHIP KNIFE IS 4-" LONG (FINAL HONING REQUIRED). POLISHED ROSEWOOD HANDLES, SECURED WITH BRASS RIVETS, ARE SHAPED FOR COMFORT AND GRIP AND BEVELED ON THE UNDERSIDE TO INDUCE THE PROPER 65° CUTTING ANGLE. USA.
|
|
|
|
Hand Tools - Carving Tools
|
VERSATILE DETAIL CARVING HANDLE COMES WITH SIX INTERCHANGEABLE CARVING TIPS
|
| 6pc Detail Carver Set
|
THE DETAIL CARVER WITH 6-PIECE CHISEL SET GIVES YOU A WIDE RANGE OF CARVING OPTIONS USING JUST ONE TOOL:
STEEL HANDLE, WITH CHUCK ON ONE END, IS KNURLED ALONG ITS LENGTH FOR A SURE, NO-SLIP GRIP - 5-1/2" LONG X 1/2" DIA. SIX, 2" LONG STEEL CHISELS INCLUDE 9MM GROOVE, 4MM FLAT, 9MM FLAT, 4MM SKEW, 7MM DEEP GOUGE AND 4MM SHALLOW GOUGE - ALSO FIT MOST POWER RECIPROCAL CARVERS. CHUCK WRENCH INCLUDED AS WELL AS VINYL STORAGE POUCHES TO KEEP COMPONENTS ORGANIZED. IMPORTED.
|
|
|
|
Hand Tools - Carving Tools
|
TWO CHERRIES - THE ULTIMATE CARVING TOOLS
|
| 50mm #1 Fishtail Chisel
...plus other(s)
|
IF YOU HAVE BEEN CARVING VERY LONG, YOU KNOW ABOUT WORLD FAMOUS TWO CHERRIES CARVING TOOLS. THEY ARE HAND FORGED USING HIGH CARBON TOOL STEEL, HEAT TREATED BY HAND AND FINELY GROUND AND MIRROR POLISHED BY HAND:
HARDENED TO RC 61 AND HEAT TREATED USING THE IMMERSION BATH METHOD (WHICH GIVES A MUCH MORE CONSISTENT HARDNESS), THESE AMAZING TOOLS WILL TAKE A LITTLE EXTRA TIME TO HONE, HOWEVER, THEY WILL STAY SHARPER LONGER THAN ALMOST ANY OTHER TOOL AVAILABLE. STEEL HOOPS FORTIFY THE HORNBEAM HANDLES AND HELP PREVENT MUSHROOMING AND SPLITTING. FINAL HONING REQUIRED PRIOR TO USE. ORDER INDIVIDUALLY OR IN SETS. GERMANY.
957-137 - 6 PIECE CARVING SET: 957-158 - #6 STRAIGHT GOUGE - 16MM. 957-165 - #11 STRAIGHT GOUGE - 14MM. 957-151 - SKEW BEVEL CHISEL - 14MM. 957-172 - STRAIGHT V-TOOL 75° - 14MM. 957-179 - #16 LONG CURVED GOUGE - 10MM. 957-144 - #8 STRAIGHT CHISEL - 6MM.
957-130 - 12 PIECE CARVING SET: 957-214 - #5 STRAIGHT GOUGE - 16MM. 957-207 - #8 STRAIGHT GOUGE - 14MM. 957-200 - #5 STRAIGHT GOUGE - 14MM. 957-186 - #1 STRAIGHT CHISEL - 14MM. 957-221 - #6 STRAIGHT GOUGE - 10MM. 957-256 - STRAIGHT V-TOOL 75° - 6MM. 957-193 - #7 STRAIGHT GOUGE - 6MM. 957-235 - SKEW BEVEL CHISEL - 6MM. 957-263 - #14 LONG CURVED GOUGE - 6MM. 957-249 - SHORT CURVED CHISEL - 3MM. 957-228 - #6 STRAIGHT GOUGE - 3MM. 957-242 - #11 STRAIGHT GOUGE - 2MM. 957-270 - NO LONGER AVAILABLE.
SPECIALITY TOOLS: 102-233 - #1 SWISS PATTERN FISHTAIL GOUGE - 50MM. 102-236 - #3 SWISS PATTERN FISHTAIL GOUGE - 50MM. 102-239 - #6 SWISS PATTERN FISHTAIL GOUGE - 50MM. 102-242 - #7 SWISS PATTERN FISHTAIL GOUGE - 50MM.
NOTE: ENGLISH CONVERSIONS ARE APPROXIMATE: 2MM = 5/64". 3MM = 7/64". 6MM = 15/64". 10MM = 25/64". 14MM = 35/64". 16MM = 15/32". 50MM = 1-31/32".
|
|
|
|
Hand Tools - Carving Tools
|
VERSATILE CARVING KNIFE SETS MADE FROM FINEST JAPANESE STAINLESS STEEL
|
| Set - 10-pc Knife
...plus other(s)
|
ALSO A LEICHTUNG WORK SHOPS® PRODUCT
THESE CARVING KNIVES REPRESENT THE MOST POPULAR SHAPES AND STYLES AVAILABLE:
96-594 - (A) 5-3/4" KNIFE FOR SMALL NOTCH CUTS; (B) 6" DETAIL KNIFE FOR WHITTLING OR SPLICING; (C) 7-3/8" ALL PURPOSE KNIFE FOR PATTERN AND MODEL BUILDING; (D) 5-5/8" DELICATE EDGE FOR INCISING FINE LINES; AND (E) 5-1/4" FINE CUT KNIFE. 96-586 - (F) 5-5/16" SKEW CHISEL BLADE; (G) 6-7/16" HEAVY DUTY SKEW CHISEL BLADE FOR HEAVY NOTCHING; (H) 6-1/8" ALL PURPOSE WHITTLING KNIFE WITH TWO SHARP EDGES; (J) 5-3/4" WITH THREE SHARP EDGES FOR CLOSE QUARTERS' PARING CUTS; AND (K) 5" HOOKED KNIFE FOR CONTROLLED SHAVING. MEASUREMENTS ARE OVERALL LENGTHS. WOODEN HANDLES WITH STAINLESS STEEL BLADES - ALL REQUIRE FINAL HONING/SHARPENING PRIOR TO USE. JAPAN.
LIMITED TO QUANTITIES ON HAND
|
|
|
|
Hand Tools - Chisels
|
JAPANESE CHISELS STAY SHARPER, LONGER
|
| 3mm Japanese Chisel
...plus other(s)
|
LAMINATED STEEL BLADES HELP MAKE JAPANESE CHISELS STAY SHARPER, LONGER AND DISTRIBUTE FORCE MORE EVENLY OVER THE WIDTH OF THE BLADE:
DEEP, TAPERED SOCKETS FIRMLY GRIP THE JAPANESE OAK HANDLES, DISTRIBUTING FORCE TO PREVENT HANDLE DAMAGE. STRAIGHT GRAINED HANDLES FEATURE A STEEL HOOP AT THE TOP TO PREVENT MUSHROOMING AND ARE SLIGHTLY BARREL SHAPED FOR A COMFORTABLE, YET CONTROLLED GRIP. HONING REQUIRED.
LIMITED TO QUANTITIES ON HAND
|
|
|
|
Hand Tools - Chisels
|
SLICE TOUGH GRAIN CLEANLY AND REACH WHERE REGULAR WOOD CHISELS CAN'T
|
| 3/4" Skew Chisel Set
...plus other(s)
|
CLEAN OUT TIGHT CORNERS IN MORTISES OR DADOES OR USE THESE QUALITY 1/2", 3/4" OR 1" SKEW CHISELS TO CLEANLY SLICE WILD, CURLY GRAINS:
ROSEWOOD HANDLES HAVE BRASS FERRULES TO HOUSE POLISHED SHEFFIELD STEEL BLADES. EACH SET OF TWO HAS A RIGHT AND LEFT HAND SKEW. OVERALL LENGTH ABOUT 12". ENGLAND.
|
|
|
|
Hand Tools - Chisels
|
STANLEY® WOOD CHISELS - AN AMERICAN TRADITION
|
| 3 Pc Chisel Set-no Case Available
...plus other(s)
|
STANLEY® WOOD CHISELS FEATURE HEAT-TREATED, PRECISION-GROUND BLADES:
EXTRA LONG, SHATTERPROOF HANDLES. HEAVY DUTY STRIKE CAPS FOR DURABILITY. 16-900 - THREE PIECE SET (1/2", 3/4", 1"). 16-901 - SIX PIECE SET (1/4", 1/2", 3/4", 1", 1-1/4", 1-1/2") INCLUDES DURABLE, COVERED STORAGE CASE. USA.
|
|
|
|
Hand Tools - Chisels
|
CORNER CHISELS TURN ROUTERED HINGE MORTISES INTO SQUARE CORNER MORTISES
|
| Corner Chisel
...plus other(s)
|
A SIMPLE TAP OF THE MALLET ON EITHER OF THESE SPRING-LOADED CORNER CHISELS SQUARES CORNERS FOR PERFECT FITTING HINGES - LIFT THE CHIP WITH A CHISEL AND YOU'RE DONE:
107-999 - 1/2" SIZE CLEANS UP AFTER 1/2" MORTISING BITS - 2-3/4"H X 1-3/16" SQUARE. 858-467 - 5/8" SIZE HANDLES 5/8" MORTISING BITS - 3-1/4"H X 1-11/16" X 1-7/16". ALSO WORK GREAT FOR CLEANING UP CORNERS FOR INSTALLING BACKINGS AND FOR PICTURE FRAMES. CUTTING EDGES EASILY RESHARPENED WITH A HAND FILE.
|
|
|
|
Hand Tools - Chisels
|
CORNER CLEARING CHISELS GO WHERE OTHERS CAN'T
|
| 3" X 1/4" Corner Cleaning Chisel
|
|
DOG LEG CORNER CLEARING CHISELS ARE IDEAL FOR CLEANING CORNERS, GROOVES AND MOLDINGS AND WORK WHERE NORMAL CHISELS CAN'T. TWO-PIECE SET (LEFT AND RIGHT HAND) HAS ROSEWOOD HANDLES. ENGLAND.
|
|
|
|
Please Wait......Searching....
to see Sub Categories)
