|
|
|
Abrasives - Accessories/replacement Back-up Pads
|
BACKUP PAD
|
| 5" Sav A Disc Set(1ea Plt Pd & Nt)
...plus other(s)
|
PATENTED SAV-A-DISC BACK-UP PADS CAN EXTEND THE LIFE OF RESIN FIBER ABRASIVE DISCS BY UP TO 3 TIMES! PATENTED SAV-A-DISC BACK-UP PADS CAN EXTEND THE LIFE OF RESIN FIBER ABRASIVE DISCS BY UP TO 3 TIMES!:
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
TO HELP COMPLETE YOUR PROJECT, MAY WE SUGGEST:
CERAMIC RESIN FIBER ABRASIVE DISCS - 127-504. ZIRCONIA ALUMINA ABRASIVE DISCS - 125-516. ALUMINUM OXIDE ABRASIVE DISCS - 100-808. SILICON CARBIDE ABRASIVE DISCS - 121-076.
|
|
|
|
Bits Drill And Boring - Accessories
|
ACCURATELY POSITION BLUM® ADAPTER PLATES FOR FACE FRAME HINGES
|
| Platemate Boring Template
...plus other(s)
|
THE BLUM® PLATEMATE™ JIG CLAMPS TO FACE FRAMES USING LEVER ACTION TO ACCURATELY POSITION ADAPTER PLATES:
ADJUSTMENT KNOB ALLOWS ACCURATE BORING IN FRAMES FROM 5/8" TO 1" THICK. SPACER SCREWS ALLOW FOR QUICK USE WITHOUT MEASURING FOR EACH PLATE. INCLUDES 2.5MM PILOT BIT AND EXTENSION, 5MM STOP COLLAR, REVERSING BUSHING SET FOR 32MM OR 40MM HOLE SPACING. LIFETIME MANUFACTURER'S WARRANTY. AUSTRIA.
|
|
|
|
Bits Drill And Boring - Specialty
|
DRILL BITS, MANDRELS AND BUSHINGS FOR PEN, PENCIL AND OTHER KITS
|
| "j" Size Drill Bit
...plus other(s)
|
DRILL BITS, MANDRELS AND BUSHINGS COME IN VARIOUS SIZES AND SHAPES NEEDED TO BUILD A WIDE VARIETY OF PEN, PENCIL AND OTHER KITS. BITS ARE 135 SPLIT TIP PARABOLIC DRILLS. OPTIMUM DRILL SPEED 900 TO 1,500 RPM. FOR USE WITH:
103-565 - FOUNTAIN PEN WITH SCREW CAP 103-568 - ROLLER BALL PEN KIT WITH SCREW CAP 103-571 - GREEK KEY PEN KIT 103-574 - DECO STYLE PEN KIT 103-577 - WAVY BLADE LETTER OPENER (FLAT) 103-583 - WAVY BLADE LETTER OPENER (ROUND) 103-589 - TOOL PEN KIT 103-592 - DETACHABLE KEYCHAIN KIT 103-601 - TOOTHPICK HOLDER/KEY RING KIT 103-586 - MAGNIFYING GLASS KIT 103-595 - BRACELET HELPER
|
|
|
|
Bits Router/tongue & Groove/straight
|
WOODTEK T&G V JOINT ROUTER BIT
|
| 82841 T&g V Joint Cutter
|
THE WOODTEK® CARBIDE-TIPPED REVERSIBLE TONGUE AND GROOVE "V" JOINT ROUTER BIT ASSEMBLY USES ONE BIT TO MAKE BOTH CUTS. THE MIDDLE CUTTER IS REPLACED WITH A BUSHING TO MAKE THE TONGUE. IDEAL FOR SHAKER STYLE CABINETS - USE WITH TABLE-MOUNTED PORTABLE ROUTERS:
RUGGED PTFE (POLYTETRAFLUOROETHYLENE) BRITEVIEW™ COATING NOT ONLY PROTECTS BUT THE BRIGHT YELLOW COLOR PROVIDES BETTER VISIBILITY FOR SAFER OPERATIONS. MICRO-GRAIN CARBIDE CUTTING SURFACES HAVE BEEN DIAMOND HONED TO 800 GRIT FOR MINIMAL TEAR-OUT AND SMOOTHER SURFACE QUALITY. CNC-MACHINING TO +/-0.001" TOLERANCES AND DYNAMIC BALANCING HELP ENSURE VIBRATION-FREE OPERATION. POSITIVE SHEAR ANGLE PLACES LESS DEMAND UPON YOUR ROUTING EQUIPMENT. MANUFACTURED IN FACILITIES MEETING STRINGENT ISO 9000:2000 QUALITY ASSURANCE STANDARDS. 1/2" SHANKS. IMPORTED.
|
|
|
|
Fasteners - Knock Down (kd)
|
35MM CAM AND DOWEL FASTENERS
|
| Swirl Cam Set-35mm Bolt
...plus other(s)
|
INSTEAD OF A ONE POINT WEDGE, THE SWIRL SUPER STRONG 35MM CAM ASSEMBLY USES A SPIRAL CLOSING ACTION THAT DRAWS BOARDS TIGHTLY AND FIRMLY TOGETHER, EVEN UNDER UNUSUAL STRESS:
M8 BUSHING IS MOUNTED INTO 10MM DIA. X 15.5MM DEEP HOLE AND M8 BOLT IS THREADED IN. 35MM DIA. X 16.3MM DEEP HOLE IS DRILLED INTO SECOND BOARD FOR ECCENTRIC CAM ALONG WITH 9MM DIA. HOLE FOR BOLT; ROTATING THE CAM WITH A 6MM HEX WRENCH TIGHTENS AND LOCKS IT ONTO THE BOLT. DESIGNED FOR 3/4" TO 1-3/8" THICK PANELS; INSTALLATION INSTRUCTIONS INCLUDED.
128-825 MODEL 358 - INCLUDES ONE 35MM ECCENTRIC CAM, ONE M8 X 35MM LONG BOLT, ONE M8 BUSHING AND ONE COVER CAP. 128-828 MODEL 558 - COMES WITH ONE, EACH, 35MM ECCENTRIC CAM, M8 X 55MM LONG BOLT, M8 BUSHING AND COVER CAP. 128-831 MODEL 3525 - OPERATION SIMILAR TO MODELS 358 AND 558 BUT DESIGNED FOR TABLE TOPS AND OTHER HORIZONTAL APPLICATIONS - INCLUDES TWO 35MM ECCENTRIC CAMS, ONE 70MM DOUBLE BOLT AND TWO COVER CAPS.
|
|
|
|
Hardware Hinges - Accessories
|
BRUSSO® HINGE ROUTING JIGS TAKE THE HAZARD OUT OF HINGING BOX LIDS
|
| Template For 811-418 Hinge
...plus other(s)
|
HINGE ROUTING JIGS, MILLED FROM SOLID BRASS, ENSURE QUICK AND PRECISE PLACEMENT OF BRUSSO® HINGES. IF YOU MAKE A LOT OF BOXES, USE TWO FOR TIME SAVINGS AND BETTER ACCURACY:
105-170 - JIG FITS 936-134 & 811-418 HINGES. 105-173 - JIG FITS 811-419 & 105-164 HINGES. 105-179 - JIG FITS 936-141 & 811-425 HINGES. 105-182 - JIG FITS 105-830 HINGES. 116-468 - TEMPLATE FITS 936-148 & 811-428 HINGES.
COMPLETE INSTRUCTIONS INCLUDED. USE 3/4" OD GUIDE BUSHING AND 1/4" CARBIDE ROUTER BIT (NOT INCLUDED).
USA.
LIMITED TO QUANTITIES ON HAND
|
|
|
|
Hardware Hinges - Butt
|
BRUSSO® BUTT HINGES FOR SMALL BOXES
|
| 3/4"l Spans 5/16" Stop Hinge
...plus other(s)
|
BRUSSO® BUTT HINGES ARE MILLED FROM SOLID BRASS AND FEATURE A FLAWLESS SATIN FINISH:
811-418 JB-101 FULL MORTISE BUTT HINGES - (3/4" LONG X 3/32" LEAF THICKNESS, SPANS 5/16" MATERIAL) HAVE BUILT-IN STOPS TO ALLOW LID TO REMAIN OPEN AT 95°. 811-425 JB-103 FULL MORTISE BUTT HINGES - (1-1/4" LONG X 3/32" LEAF THICKNESS, SPAN 7/16" MATERIAL); OPERATION SIMILAR TO JB-101. 811-419 JB-102 FULL MORTISE BUTT HINGES - (1-1/4" LONG X 3/32" LEAF THICKNESS, SPANS 5/16" MATERIAL); OPERATION SIMILAR TO JB-101. 105-830 JB-804 STOP HINGES - (1-1/4" X 1-1/32, 3/16" LEAF THICKNESS, 1/8" RADIUS CORNER) PROVIDE BUILT-IN STOPS, ALLOWING LID TO REMAIN OPEN AT ABOUT 95° - USE WHEN ADDITIONAL STAYS NOT DESIRED. MORTISE FLAT INTO BOX AND LID. HINGE PINS ARE TOOL STEEL, FITTED TO PRECISION-REAMED BORES. SOLD IN PAIRS (MOUNTING SCREWS INCLUDED)..
OPTIONAL HINGE ROUTING JIGS, MILLED FROM SOLID BRASS, ENSURE QUICK AND PRECISE PLACEMENT OF BRUSSO® HINGES:
TJ-101 JIG - JB-101 HINGES. TJ-102 JIG - JB-102 HINGES. TJ-103 JIG - JB-103 HINGES. COMPLETE INSTRUCTIONS INCLUDED. USE 3/4" OD GUIDE BUSHING AND 1/4" CARBIDE ROUTER BIT (NOT INCLUDED). USA.
|
|
|
|
Hardware Hinges - Concealed
|
SOSS® INVISIBLE HINGES - BEAUTIFUL WHEN OPEN, INVISIBLE WHEN CLOSED
|
| 3/8"x1" Soss Hinge-sat. Brass
...plus other(s)
|
SAFETY AND SECURITY AS WELL AS A CLEAN, CONTEMPORARY LOOK ARE EASY WITH SOSS® INVISIBLE HINGES:
WHEN CLOSED, HINGES CANNOT BE SEEN OR TAMPERED WITH - WHEN OPEN, RIVETED PINS CANNOT BE REMOVED (HINGE OPENS TO 180°). HIGH-STRENGTH PLATED STEEL AND HEAVY-DUTY ZINC ALLOY CASTINGS. CHOOSE FROM SB-SATIN BRASS, SC-SATIN CHROME, EE-EBONY EPOXY FINISHES IN A NUMBER OF SIZES. TO INSTALL, MORTISE OUT WOOD DOOR AND JAMB USING A DRILL BIT AND CLEAN UP WITH A CHISEL (PAPER TEMPLATE, INSTRUCTIONS AND MOUNTING SCREWS INCLUDED). SMALLER HINGES SOLD IN CARDED PAIRS; 2-3/4 AND LARGER HINGES SOLD EACH. IMPORTED.
FOR FASTER AND MORE ACCURATE HINGE INSTALLATION, THE OPTIONAL SOSS® ROUTER GUIDE TEMPLATE ENSURES A PERFECT MORTISE:
INDIVIDUALLY HANDCRAFTED TEMPLATE FASTENS TO DOOR AND JAMB WITH NAILS - GUIDE PINS LOCATE THE DEEP MORTISE. ROUTER, ROUTER BIT AND 3/4" O.D. GUIDE BUSHING WITH LOCK NUT REQUIRED (NOT INCLUDED). 101 SERIES TEMPLATE - USE WITH 1/4" DIA BIT. 103 SERIES TEMPLATE - USE WITH 3/8" DIA BIT. 203 SERIES TEMPLATE - USE WITH 3/8" DIA BIT. 204 SERIES TEMPLATE - USE WITH 3/8" DIA BIT. 208 SERIES TEMPLATE - USE WITH 3/8" DIA BIT. 216 SERIES TEMPLATE - USE WITH 1/2" DIA BIT.
|
|
|
|
Hardware Hinges - Pivot
|
WOOD DOOR PIVOT HINGES
|
| Black Pivot Hinge For Wood
|
WHEN USING THESE PIVOT HINGES HINGE PIN BUSHINGS INSTALL INTO HOLES DRILLED INTO THE CABINET:
SLOTTED HOLES ALLOW FOR ±3/16" HORIZONTAL ADJUSTMENT AFTER INSTALLATION. BLACK, POWDER COATED FINISH (MOUNTING SCREWS INCLUDED). FOUR PAIRS PER PACKAGE. WORK FOR EITHER LEFT OR RIGHT-HAND DOORS
|
|
|
|
Hardware Locks And Latches - Catches And Bolts
|
BRUSSO® SOLID BRASS CATCHES FOR CASES AND CHESTS
|
| Solid Brass Box Latch
...plus other(s)
|
TYPICAL HIGH QUALITY FROM THE BRUSSO® HARDWARE LINE, THE MODEL JB-828 SOLID BRASS JEWELRY BOX LATCH WILL ADD BEAUTY AND ELEGANCE TO ALMOST ANY BOX PROJECT:
2"L X 3/4"W LATCH IS MORTISED INTO THE LID AND FRONT OF A BOX OR CASE. SPRING LOADED PIVOTING BAR RELEASES THE LATCH BY PRESSING ON THE BUTTON. OPTIONAL TJ-828 SOLID BRASS TEMPLATE SIMPLIFIES BOX LATCH INSTALLATION. USE 3/4" OD GUIDE BUSHING AND 1/4" CARBIDE TIPPED ROUTER BIT (NOT INCLUDED). BALL CATCHES HAVE MACHINED BODIES AND STRIKES WITH TOOL STEEL BALLS FOR DURABILITY AND SMOOTH PERFORMANCE. USA.
|
|
|
|
Hardware Shelf And Support - Shelf Pins
|
LIBRARY STYLE SHELF PINS AND SLEEVES
|
| 10mm Brass Bushing For 6.9mm Pin
...plus other(s)
|
LIBRARY STYLE SHELF PINS AND SLEEVES ENHANCE THE APPEARANCE AND PERFORMANCE OF ADJUSTABLE SHELVES. SOLD SEPARATELY, SO YOU CAN PUT A BUSHING INTO EACH HOLE BUT USE SHELF PINS ONLY WHERE NEEDED:
PRESS-TO-FIT, 9MM AND 10MM OUTSIDE DIA. SMOOTH SHELF BUSHINGS ACCEPT 6.9MM DIA. SMOOTH SHELF PINS. SPOON SHAPED SUPPORTS HAVE AN 11MM WIDE X 13MM LONG SURFACE (7/16" X 9/16") SLEEVES ADD DURABILITY TO WOODEN SURFACES AND DRESS UP THE SHELF PIN HOLES. EXTRA SECURITY FOR SLEEVES CAN BE ACHIEVED BY ADDING A SMALL DROP OF WOOD GLUE WHEN THE SLEEVES ARE INSERTED. SLEEVES AND PINS SOLD IN BAGS OF 10 EACH OR BAGS OF 100 EACH. THESE PINS MUST BE USED WITH SLEEVES. IMPORTED
|
|
|
|
Hardware Shelf And Support - Shelf Pins
|
LOCKING GLASS SHELF SUPPORTS
|
| 1/4" Glass Clip-brass
...plus other(s)
|
LOCKING GLASS SHELF CLIPS INCLUDE RUBBER TIPPED NYLON SCREWS TO SECURE GLASS:
BRASS OR CHROME FINISHES PROVIDE A DECORATIVE ACCENT. PLATED STEEL BRACKETS ARE 3/4" SQUARE. 941-602 AND 941-609 HAVE 5MM PINS AND INCLUDE NYLON BUSHINGS SO THEY CAN BE USED AS PIVOT HINGES FOR SMALL GLASS DOORS. NYLON INSERTS ARE NOT DESIGNED FOR USE AS SLEEVES IN SHELF APPLICATIONS.. SOLD IN BAGS OF 4.
|
|
|
|
Hardware Shelf And Support - Shelf Pins
|
SOLID BRASS THREADED LIBRARY SHELF PINS
|
| 9mm Threaded Bushing
...plus other(s)
|
SPECIALLY DESIGNED SHELF PINS THREAD INTO EXPANSION BUSHINGS TO LOCK THESE SHELF SUPPORTS IN PLACE:
11/32" DIA. (9MM) X 3/8" DEEP HOLE REQUIRED. BOTH COMPONENTS ARE SOLID BRASS FOR IMPROVED APPEARANCE AND DURABILITY. SOLD IN BAGS OF 10 PINS OR 10 BUSHINGS. NOTE: SHELF PINS MUST ONLY BE USED WITH THESE THREADED BUSHINGS. IMPORTED
|
|
|
|
Machinery Accessories - Drill Presses
|
TURN YOUR DRILL PRESS INTO A MORTISING MACHINE WITH A DELTA® MORTISING ATTACHMENT KIT
|
| 17-924 Mortising Kit
|
THE VERSATILE DELTA® MODEL 17-924 MORTISING ATTACHMENT KIT COMES WITH FOUR POPULAR MORTISING CHISEL AND BIT SETS PLUS A HANDY CARRYING CASE THAT HOLDS EVERYTHING FOR EASY STORAGE:
ATTACHES TO DRILL PRESS IN MINUTES WITHOUT THE NEED FOR INSTALLATION TOOLS. LARGE 4" CAPACITY UNDER HOLD DOWN - 2-3/4" CAPACITY FROM ENDS OF CLAMP RODS TO FENCE. COMES WITH 1/4" X 1/4", 5/16" X 5/16", 3/8" X 3/8" AND 1/2" X 1/2" HOLLOW CHISELS AND DRILL BITS, SPECIAL ALIGNMENT GAUGE FOR FAST, ACCURATE SET UPS, LARGE, CAST IRON FENCE ASSEMBLY, BUSHINGS, GUIDES, HEX WRENCH AND INSTRUCTIONS. FITS DRILL PRESSES WITH 38MM, 48MM, 50.8MM AND 66MM QUILL DIAMETERS, INCLUDING DELTA® MODELS 11-090, 11-980, 11-990, 14-040, 14-070, 17-900, 17-925 AND 17-965, PLUS SEARS® MODELS 21313, 21315 AND 21317. KIT WEIGHS 16 LBS. TWO YEAR MANUFACTURER'S WARRANTY. IMPORTED.
|
|
|
|
Machinery Accessories - Drill Presses
|
WOODTEK MORTISING ATTACHMENT FOR DRILL PRESS
|
| Mortising Attachment For Wdtk Dp
|
THE WOODTEK® MORTISING ATTACHMENT INSTALLS EASILY AND ADDS A SIGNIFICANT CAPABILITY TO YOUR DRILL PRESS:
INCLUDES CAST IRON CHISEL HOLDER (CHISELS NOT INCLUDED), FENCE ASSEMBLY, BUSHINGS, GUIDES, COLLAR, STEEL RODS AND HARDWARE. IN ADDITION TO WOODTEK® 21" DRILL PRESSES, THE ATTACHMENT FITS DELTA® AND CRAFTSMAN® 20" DRILL PRESSES AS WELL AS OTHERS WITH 2-15/16" COLLARS. 11-1/4 LBS. SHIPPING WEIGHT. ONE YEAR MANUFACTURER'S WARRANTY. IMPORTED.
|
|
|
|
Machinery Accessories - Drill Presses
|
VERSA-GRINDER CARBIDE SHARPENING TOOL
|
| Versa-grinder & 180x Wheel
...plus other(s)
|
VERSA-GRINDER™ IS A PATENTED, SHARPENING SYSTEM FOR RESTORING THE CUTTING EDGES ON SHAPER CUTTERS AND ROUTER BITS:
BASE MOUNTS ONTO DRILL PRESS TABLE AND DIAMOND SHARPENING WHEEL GOES INTO DRILL PRESS CHUCK (MAXIMUM 9,000 RPM). CHUCK A ROUTER BIT INTO THE FIXTURE COLLET OR MOUNT A SHAPER CUTTER ONTO THE ENCLOSED MANDREL - ADVANCE THE FIXTURE INTO THE SPINNING WHEEL AND HONE EDGES, PERFECTLY. INDEXED COLLET ADJUSTS FOR PRECISE SHEAR AND HOOK ANGLES. SO PRECISE, IT REPEATS OPERATIONS TO WITHIN 0.002". INCLUDES 1/2" INDEXED COLLET, 1/2", 1/4", 3/8" REDUCER BUSHINGS, 1/2" MANDREL FOR SHAPER CUTTERS WITH 3/4", 1", 1-1/4" BUSHINGS, 180 GRIT DIAMOND WHEEL WITH MANDREL (OPTIONAL 400 GRIT WHEEL HONES BITS TO A KEEN EDGE), EDGE FENCE AND COMPLETE INSTRUCTIONS AND VIDEOTAPE. USA. U.S. PATENT NO. 5,816,898.
|
|
|
|
Machinery Accessories - Mortisers
|
POWERMATIC® TILTING TABLE HOLLOW CHISEL MORTISER EXCELLENT CHOICE FOR PRODUCTION FACILITIES
|
| 1-1/8" Mortise Chisel Bushing
...plus other(s)
|
THE HEAD ON THE POWERMATIC® MODEL 719T TILTING TABLE HOLLOW CHISEL MORTISER IS MOUNTED USING ADJUSTABLE GIBS TO ENSURE YEARS OF TROUBLE FREE SERVICE:
1HP, 115V/230V (PREWIRED 115V), 1PH, 1,725 RPM MOTOR - 1/2" CHUCK EASILY ACCESSIBLE THROUGH HINGED DOORS. 10-3/4" MAXIMUM CHISEL STROKE; 6" MAXIMUM HEAD STROKE - RACK AND PINION GEAR SYSTEM USES SPRING LOADED, SIX POSITION ADJUSTABLE HANDLE. 1/4" TO 1" CHISEL CAPACITY - 5/8", 3/4", 1-1/8" CHISEL SHANK DIAMETERS. 7" X 20-1/4" WOODEN TABLE TILTS 0°-35°; ADJUSTS LEFT, RIGHT, FRONT AND BACK - 4-1/2" X 20-1/4" METAL FENCE. STEEL CABINET BASE, WORK STOPS, CHUCK KEY, DRILL BIT ADAPTER, QUICK RELEASE VISE, CHUCK EXTENSION ADAPTER AND HARDWARE INCLUDED. 74"H X 21-5/8"W X 21-1/4"D. 276 LBS. NET WEIGHT; 292 LBS. SHIPPING WEIGHT. FIVE YEAR MANUFACTURER'S WARRANTY. IMPORTED.
|
|
|
|
Machinery Accessories - Shapers
|
WOODTEK USA SHAPER SPINDLE ROUTER COLLET FOR DELTA SHAPER
|
| Router Collet For Delta Hd 2-spd Shaper
...plus other(s)
|
|
132-315 FITS 3/4" DELTA® HEAVY DUTY SHAPERS. 132-316 FITS 1/2" DELTA® LIGHT DUTY SHAPERS (REQUIRES A FALSE TABLE TO ELEVATE STOCK; PLAN INCLUDED). PRECISION MADE FOR HIGH QUALITY SHAPING. 1/2" COLLET; 1/4" SPLIT BUSHING INCLUDED. USA.
|
|
|
|
Machinery Accessories - Shapers
|
WOODTEK SHAPER CUTTER BUSHINGS AND SPACERS
|
| Double T-bushing 1-1/4"od 1"id 15/16"h
...plus other(s)
|
USE DURABLE STEEL WOODTEK® SHAPER CUTTER BUSHINGS AND SPACERS TO GREATLY EXPAND YOUR SHAPER CUTTER'S CAPACITY:
BUSHINGS ADAPT CUTTERS TO YOUR SHAPER SPINDLE. SPACERS HELP POSITION CUTTERS ON THE SPINDLE. IMPORTED.
|
|
|
|
Machinery Components - Blocks & Sheaves
|
BALL BEARING DOUBLE END MANDREL
|
| Ball Bearing Double End Mandrel
...plus other(s)
|
SELF ALIGNING POWER DRIVE MANDRELS COME IN TWO STYLES:
818-760 - BRONZE BUSHING MANDRELS USE LESS EXPENSIVE, FIXED BEARINGS. THEY SHOULD BE USED AT SLOWER SPEEDS AND OCCASIONALLY REQUIRE OIL. 818-753 - BALL BEARING MANDRELS CAN TURN AT HIGHER SPEEDS, ARE MAINTENANCE FREE AND QUIETER. TIGHTER TOLERANCES MEAN LONGER LIFE AND MORE CONSISTENT RUNNING. BOTH MANDRELS ARE THREADED ON EACH END TO RUN TWO WHEELS AT ONCE; 1/2"-20 THREADS; 5/8" X 12" SHAFT. FLANGES, NUTS AND PULLEYS (EXCEPT MOTOR PULLEY) INCLUDED.
|
|
|
|
Machinery - Mortisers
|
WOODTEK 1HP BENCH TOP MORTISER
|
| 1hp Bench Top Mortiser 120/230v
...plus other(s)
|
IN ADDITION TO A POWERFUL MOTOR FOR CONTINUOUS OPERATION AND AN IMPRESSIVE 6-1/2" STROKE, THE GAS FILLED HEAD STABILIZER ON THIS WOODTEK® BENCHTOP HOLLOW CHISEL MORTISER PROVIDES SMOOTH, PRECISE CONTROL NECESSARY FOR A PRODUCTION ENVIRONMENT:
COVERS ON BOTH SIDES OF HEAD PROVIDE FASTER, EASIER ACCESS WHILE RACK AND PINION GEARING AND BUILT IN, ADJUSTABLE STOP ROD ARE IDEAL FOR REPETITIVE MORTISING. HEAVY CAST IRON CONSTRUCTION - WRENCHLESS ADJUSTMENTS. 1-1/8" BORE AND BUSHING TO HOLD 5/8" SHANK CHISELS. 22" LONG HANDLE, HARDWARE AND COMPLETE INSTRUCTIONS INCLUDED (CHISEL AND BIT NOT INCLUDED). ONE YEAR PARTS AND WORKMANSHIP WARRANTY. IMPORTED.
SPECIFICATIONS:
MOTOR - 110VAC, 6.8A, 1PH, 1,720 RPM - 1/2" KEYED CHUCK (8' LONG POWER CORD AND PLUG INCLUDED). ON/OFF SWITCH - TOGGLE, MECHANICAL. CHISEL CAPACITY - 1/4" TO 5/8". VERTICAL SPINDLE TRAVEL - 6-1/2". HOLDDOWN CAPACITY - 7-3/16" UNDER 1/4" CHISEL; 9/16" MINIMUM STOCK THICKNESS. STOP ROD CAPACITY (LENGTH) - 14-1/4". TABLE SIZE - 7-3/8" X 6-1/4". FENCE SIZE - 2" X 11". VISE CAPACITY - 5-1/16". OVERALL DIMENSIONS - 28-1/2"H (NOT INCLUDING HANDLE) X 12"W X 13-3/4"D. SHIPPING WEIGHT - 85 LBS. NOTE: ALTHOUGH DEEMED ACCURATE, SPECIFICATIONS ARE NOT GUARANTEED.
WE STOCK MORE THAN 5,000 WOODTEK® PARTS IN OUR WYOMING WAREHOUSE. EXPERIENCED TECHNICIANS READY TO ASSIST YOU - SAME DAY SHIPPING ON MOST ORDERS. 1-800-545-9663, M-F, 7AM-4PM, MOUNTAIN TIME.
|
|
|
|
Machinery - Mortisers
|
POWERMATIC PM701 BENCH TOP MORTISER
|
| Pm701 Bench Top Mortiser
...plus other(s)
|
THE POWERMATIC® PM701 BENCHTOP MORTISER ACCEPTS 5/8" AND 3/4" SHANK CHISELS AND FEATURES AN EASY-ACCESS CHUCK AND INTEGRATED BIT-TO-CHISEL SPACER SYSTEM THAT MAKE CHISEL AND BIT CHANGES QUICK AND EASY THE POWERMATIC® PM701 BENCHTOP MORTISER ACCEPTS 5/8" AND 3/4" SHANK CHISELS AND FEATURES AN EASY-ACCESS CHUCK AND INTEGRATED BIT-TO-CHISEL SPACER SYSTEM THAT MAKE CHISEL AND BIT CHANGES QUICK AND EASY:
3/4HP, 115V, 1PH MOTOR - 1,725 RPM SPINDLE SPEED. MECHANICAL ON/OFF SWITCHADJUSTABLE, IN-LINE DEPTH STOP ALLOWS YOU TO STOP AT PRESET DEPTHS WITHOUT RACKING THE BIT TO THE BASE.5-1/2" HEAD STROKE; 5" CAPACITY UNDER HOLDDOWN; 1/2" CHISEL CAPACITY; 3/4" CHISEL SHANK CAPACITY.COMES WITH BUILT-IN BIT AND CHISEL HOLDER WITH SHARPENING STONE (BITS AND CHISELS NOT INCLUDED), REVERSIBLE HANDLE, 2-5/8" X 12-1/2" CAM LOCK FENCE, 5/8" AND 3/4" BUSHINGS, 4" CHUCK KEY, REMOVABLE SAFETY SWITCH KEY AND INSTRUCTIONS.13-3/4" X 16-5/16" BASE.93 LBS. NET WEIGHT; 100 LBS. SHIPPING WEIGHT.FIVE YEAR MANUFACTURER'S WARRANTY.IMPORTED.
|
|
|
|
Machinery - Mortisers
|
WOODTEK 1/2HP HOLLOW CHISEL MORTISER
|
| 1/2hp Hollow Chisel Mortiser
...plus other(s)
|
A GAS-FILLED HEAD STABILIZER GIVES THE WOODTEK® 1/2HP HOLLOW CHISEL MORTISER SMOOTH, PRECISE CONTROL - RACK-AND-PINION GEARING AND BUILT-IN, ADJUSTABLE STOP RODS FOR REPETITIVE MORTISING:
MOTOR - 120VAC, 6A, 1PH, 1,725 RPM - 3/8" KEYED CHUCK. ON/OFF SWITCH - TOGGLE, MECHANICAL. CHISEL CAPACITY - 5/8" TO 3/4" SHANK DIA. STROKE - 4-3/4". HOLDDOWN CAPACITY - 4-1/4". TABLE SIZE - 7-3/4" X 13-3/4". FENCE SIZE - 1-1/2" X 13-3/4". OVERALL DIMENSIONS - 30-1/4"H (NOT INCLUDING HANDLE) X 13-3/4"W X 13-3/8"D. NET WEIGHT - 45 LBS. SHIPPING WEIGHT - 50 LBS. BUSHINGS, 8' LONG POWER CORD AND PLUG, CHUCK KEY, 28" LONG HANDLE, WRENCHES, HARDWARE AND COMPLETE INSTRUCTIONS INCLUDED. ONE YEAR PARTS AND WORKMANSHIP WARRANTY. IMPORTED.
NOTE: ALTHOUGH DEEMED ACCURATE, SPECIFICATIONS ARE NOT GUARANTEED.
WE STOCK MORE THAN 5,000 WOODTEK® PARTS IN OUR WYOMING WAREHOUSE. EXPERIENCED TECHNICIANS READY TO ASSIST YOU - SAME DAY SHIPPING ON MOST ORDERS. 1-800-545-9663, M-F, 7AM-4PM, MOUNTAIN TIME.
TO HELP COMPLETE YOUR PROJECT, MAY WE SUGGEST:
MORTISER CHISEL AND BIT SETS - 124-248.
|
|
|
|
Machinery - Mortisers
|
WOODTEK 1 HORSE POWER MORTISER FLOOR STANDING
|
| 1hp Mortiser Floor Standing 230v
...plus other(s)
|
HEAVY DUTY CONSTRUCTION THROUGHOUT ALLOWS THIS WOODTEK® CHISEL MORTISER TO MAKE CLEAN, QUICK MORTISE CUTS UP TO 1" IN SOFTWOODS OR 3/4" IN HARDWOODS - 28" LONG HANDLE WITH RUBBER GRIP FOR LEVERAGE:
COUNTER BALANCED HEAD ENSURES EASIER BORING. DURABLE CAST IRON TABLE FEATURES INTEGRATED FENCE AND ACME THREADED ROD ADJUSTMENT. SINGLE HAND WHEEL CONTROLS LONGITUDINAL AND LATERAL MOVEMENT WHILE A POWERFUL CLAMP SECURES MATERIAL UP TO 10" X 7". ENCLOSED STAND, TABLE INSERT, TOOLS, HARDWARE AND COMPLETE INSTRUCTIONS INCLUDED. ONE YEAR PARTS AND WORKMANSHIP WARRANTY. IMPORTED.
SPECIFICATIONS:
MOTOR - 1HP, 230V, 7A, 1PH, 1,720 RPM MOTOR - (8' LONG POWER CORD INCLUDED, PLUG NOT INCLUDED). ON/OFF SWITCH - PUSH BUTTON, MAGNETIC. BUSHINGS - 5/8". 3/4", 1-1/8". CAPACITY - 10" X 7" WITH 5" STROKE. TABLE SIZE - 20-1/4" X 6-1/2"; ADJUSTS 16" SIDE TO SIDE AND 3-1/2" IN AND OUT. FENCE SIZE - 20-1/4" X 3-3/4". OVERALL DIMENSIONS - 57-1/2"H X 26-1/2"W X 20-1/2"D OVERALL. NET WEIGHT - 352 LBS. SHIPPING WEIGHT - 442 LBS. NOTE: ALTHOUGH DEEMED ACCURATE, SPECIFICATIONS ARE NOT GUARANTEED.
WE STOCK MORE THAN 5,000 WOODTEK® PARTS IN OUR WYOMING WAREHOUSE. EXPERIENCED TECHNICIANS READY TO ASSIST YOU - SAME DAY SHIPPING ON MOST ORDERS. 1-800-545-9663, M-F, 7AM-4PM, MOUNTAIN TIME.
TO HELP COMPLETE YOUR PURCHASE, MAY WE SUGGEST:
HOLLOW MORTISE CHISEL AND BIT SETS - 42-317.
|
|
|
|
Picture Framing - Hardware
|
PLAQUE AND MIRROR FASTENERS
|
| Plaque/mirror Fastener-pol. Brass
...plus other(s)
|
THESE FASTENERS ARE DESIGNED FOR QUICK AND SECURE FASTENING OF MIRRORS OR PLAQUES USING THROUGH-HOLE MOUNTING:
FIT INTO 1/4" DIA. MOUNTING HOLES DRILLED IN MIRROR OR PLAQUE.PLASTIC INSERT BUSHINGS GUIDE SCREWS AND PROTECT WORKPIECES FROM DAMAGE. PACKAGES OF 10 INCLUDE SCREWS, BUSHINGS AND DECORATIVE SCREW CAPS. AVAILABLE IN CHROME OR POLISHED BRASS FINISHES. IMPORTED.
|
|
|
|
Portable Power Tool Accessories - Dovetail Jigs
|
LEIGH SUPER JIGS CAN PRODUCE AN AMAZING NUMBER OF DOVETAIL JOINT OPTIONS RIGHT OUT OF THE BOX
|
| Super 12" Dovetail Jig
...plus other(s)
|
IF IT'S FAST PRODUCTION YOU WANT, THE LEIGH SUPER JIG LETS YOU ROUT HALF BLIND PIN BOARDS AND TAIL BOARDS...AT THE SAME TIME! AND WHEN YOU USE THE INCLUDED TWO FUNCTION SPACER TO OFFSET THE TAIL BOARD YOU CAN ROUT COMPLETE JOINTS IN ONE PASS. INFINITELY ADJUSTABLE ONE PIECE FINGERS ARE EASILY POSITIONED FOR ANY JOINT PATTERN AND YOU ARE ALWAYS GUARANTEED A HALF PIN AT EACH EDGE OF THE JOINT, REGARDLESS OF BOARD WIDTH:
LEIGH SUPER 12 LETS YOU PRODUCE VARIABLY SPACED THROUGH AND HALF BLIND DOVETAILS, 5/16" AND 5/8" BOX JOINTS AND SINGLE PASS HALF BLIND DOVETAILS IN MULTIPLE SIZES - 7/8" TO 12" WORK PIECE WIDTH; 13 FINGERS. LEIGH SUPER 18 OFFERS THE SAME CAPABILITIES AS THE SUPER 12. ADD AN OPTIONAL F18 FINGER JOINT TEMPLATE AND ISOLOC I18B CLOVER & BEARS EARS TEMPLATE FOR ADDITIONAL VERSATILITY - 7/8" TO 18" WORK PIECE WIDTH; 16 FINGERS. LEIGH SUPER 24 HAS CAPABILITIES SIMILAR TO SUPER 18. OPTIONAL F24 FINGER JOINT TEMPLATE PLUS ISOLOC I24A KEY & MIRROR AND I24B CLOVER & BEARS EARS TEMPLATES ADD CAPABILITIES - 7/8" TO 24" WORK PIECE WIDTH; 19 FINGERS. EACH SUPER JIG COMES WITH 8° AND 14° DOVETAIL BITS, 5/16" STRAIGHT BIT, 1/2" TO 8MM COLLET REDUCER, TEMPLATE GUIDE, CAM ACTION SPEED CLAMP, SLIDING DOVETAIL FENCE, SCREWDRIVER, USER GUIDE, INSTRUCTIONAL DVD, SPACER, E-BUSH OVAL GUIDE BUSHING AND HALF-BLIND BRIDGE MATERIAL. FIVE YEAR MANUFACTURER'S WARRANTY. CANADA.
OPTIONAL AC12, AC16 (LEIGH D1600 JIG ONLY), AC18 OR AC24 ACCESSORY KIT CONTAINS A 7 PC., 8MM SHANK BOXED ROUTER BIT SET (1/4", 5/16", 3/8", 7/16" THROUGH AND 1/2" 10°, 12°, 18° HALF BLIND DOVETAIL) PLUS A VRS VACUUM & ROUTER SUPPORT.
OPTIONAL VRS12, VRS18, VRS24 OR VRSD24 (FITS DR4 AND ALL 24" D-SERIES JIGS) VRS VACUUM & ROUTER SUPPORT LETS YOU POSITION YOUR ROUTER BETWEEN THE CONTROL ARMS ATTACHED TO THE VACUUM CHUTE, WHICH GLIDES FROM SIDE TO SIDE ON NYLON ROLLERS AND AUTOMATICALLY FOLLOWS THE ROUTER WHEN MAKING THE JOINT OR WHEN THE ROUTER IS PARKED OFF TO THE SIDE. MOUNTING HARDWARE INCLUDED; ADAPTS TO ANY 1-1/2" TO 2" DIA. HOSE.
|
|
|
|
Portable Power Tool Accessories - Dovetail Jigs
|
PATENT PENDING CHESTMATE™ DOVETAIL JIG IS EASY TO USE, ACCURATE AND AFFORDABLE
|
| Prazi Chestmate Dovetail Jig
|
USING THE DURABLE, CAST ALUMINUM PRAZI PR-3900 CHESTMATE™ DOVETAIL JIG AND YOUR ROUTER AND ACCESSORIES, YOU CAN CUT ANY PATTERN OF PINS AND TAILS IN ANY WIDTH STOCK 1/2" TO 1" THICK:
INSTEAD OF CLAMPING A WORKPIECE INTO A DOVETAIL JIG, YOU SECURE THE WORKPIECE ONTO YOUR BENCH AND CLAMP CHESTMATE™ ONTO THE EDGE OF THE BOARD. THEN, FOLLOWING AN EASILY CONSTRUCTED INDEXING BOARD, YOU ROUT YOUR OWN VARIABLE OR FIXED SPACE DOVETAIL JOINTS. REQUIRES A STANDARD ROUTER WITH 6" DIA. BASE (LARGE INDUSTRIAL ROUTER NOT RECOMMENDED), 5/8" DIA. X 1/2" LONG FOLLOWER BUSHING, 3/4" 14° DOVETAIL AND 5/16" STRAIGHT ROUTER BITS PLUS A SECURELY MOUNTED BENCH VISE AND SHOP CLAMPS. COMPLETE INSTRUCTIONS AND PIN AND TAIL INSERTS INCLUDED. APPROX. 3"H X 8"W X 9"D. 3-3/4 LBS. SHIPPING WEIGHT. LIFETIME MANUFACTURER'S WARRANTY. IMPORTED.
TO HELP COMPLETE YOUR PROJECT, MAY WE SUGGEST:
WOODTEK® 5/16" STRAIGHT ROUTER BIT, 1/4" SHANK - 110-186. WOODTEK® 5/16" STRAIGHT ROUTER BIT, 1/2" SHANK - 110-192. FREUD® 3/4" 14° DOVETAIL ROUTER BIT, 1/4" SHANK - 129-233. WOODTEK® 3/4" 14° DOVETAIL ROUTER BIT, 1/2" SHANK - 819-452. WOODTEK® C-CLAMPS - 114-647. JORGENSEN® 10" BENCH VISE - 801-744. PORTER-CABLE® TEMPLATE GUIDE - 107-144.
|
|
|
|
Portable Power Tool Accessories - Dovetail Jigs
|
DOVETAIL YOUR NEXT WOODWORKING PROJECTS IN MINUTES WITH KELLER 15" DOVETAIL JIG SYSTEMS
|
| 15" Journeyman Jig System
...plus other(s)
|
WHETHER YOU ARE A PROFESSIONAL WOODWORKER OR A WEEKEND HOBBYIST, YOU'LL FIND THAT KELLER 15" DOVETAIL JIG SYSTEMS ARE EASY AND EFFICIENT AND PROVIDE PERFECT RESULTS:
934-385 - MODEL 1500 JOURNEYMAN COMBINES TAIL AND PIN TEMPLATES IN ONE, BACK TO BACK, 15" LONG PHENOLIC TEMPLATE. ROUT DOVETAILS IN ANY 1/8" TO 3/4" THICK STOCK. ECONOMICAL CHOICE FOR BEGINNER AND HOBBYIST SMALL TO MID-SIZED PROJECTS.
951-597 - USE THE MODEL 1601 PRO SERIES TO CUT FIXED OR VARIABLE WIDTH DOVETAILS, EVEN FOR ANGLED OR CURVED JOINTS. TWO, 16" LONG ALUMINUM TEMPLATES WORK ON ANY STOCK FROM 1/8" TO 3/4" THICK AND ARE GUARANTEED BY THE MANUFACTURER FOR 20 YEARS. DESIGNED FOR SMALL TO MEDIUM SIZE WOODWORKING PROJECTS.
BOTH JIGS INCLUDE ONE CARBIDE TIPPED 7/16" X 7°, 1/4" SHANK DOVETAIL BIT AND ONE CARBIDE TIPPED 5/8", 1/4" SHANK STRAIGHT BIT, BOTH WITH BALL BEARING GUIDES (NO BUSHINGS REQUIRED) AND COMPLETE INSTRUCTIONS. BOTH REQUIRE A SIMPLE, WOODEN MOUNTING BLOCK (NOT INCLUDED).
|
|
|
|
Portable Power Tool Accessories - Dovetail Jigs
|
SET - MATCH MAKER TO FIT BOSCH 1613 ROUTER
|
| Matchmaker For Bosch 1613 Router
...plus other(s)
|
MATCHMAKER™ HANDLES TENONING, BOX JOINT CUTTING, DOVETAILING, SHUTTER MORTISE CUTTING AND MUCH MORE. BY COMBINING A TABLE THAT MOVES 6", IN OR OUT, AND 12", LEFT TO RIGHT, WITH A ROUTER THAT MOVES UP TO 5-1/2", VERTICALLY, MANY CONVENTIONAL (AND SOME NOT SO CONVENTIONAL) JOINTS CAN BE CUT QUICKLY AND ACCURATELY - WITHIN 0.005"!
BY SIMULTANEOUSLY CONTROLLING THE POSITIONS OF THE 17-1/2" X 11-1/4" TABLE AND CUTTERHEAD, THE OPERATOR MAKES THE STYLUS FOLLOWER TRACE THE TEMPLATE WHILE THE ROUTER IS SHAPING THE WORKPIECE TO MATCH THE TEMPLATE. 6" MAXIMUM CUT DEPTH. 5"H X 10"W MAXIMUM TENON SIZE - TENONS TAKE ONLY A FEW SECONDS ON A MACHINE THAT'S SMALL ENOUGH TO FIT INTO ALMOST ANY SHOP. CHANGEOVER TIME TO SWITCH FROM ONE CUTTING OPERATION TO ANOTHER IS ABOUT TWO MINUTES. INCLUDES ALIGNMENT TOOL (113-415) TO ENSURE ACCURATE ROUTER MOUNTING (ROUTER NOT INCLUDED), CHIP GUARD, TEMPLATE HOLDER, QUICK ACTION CLAMP, FENCES FOR REPEATABLE CUTTING AND 20 MINUTE INSTRUCTIONAL VIDEOTAPE. APPROXIMATELY 15"H X 17-1/2"W X 22-1/2"D. WEIGHS 58 LBS. OPTIONAL RETROFIT ROD PAIRS ALLOW LISTED ROUTERS TO BE USED ON EXISTING MATCHMAKER™ MACHINES. INVENTED IN USA - U.S. PATENTS #4,593,735 AND #4,909,292 - ASSEMBLED IN USA.
SEE "MATCHMAKER™ IN ACTION": 20-MINUTE VIDEOTAPE (825-534) SHOWS TENONING, BOX JOINT CUTTING, DOVETAILING, SHUTTER MORTISE CUTTING AND MORE. PURCHASE PRICE REFUNDABLE ON MATCHMAKER™ ORDER OR CAN BE APPLIED TOWARDS A GIFT CERTIFICATE. IF YOU ALREADY OWN A MATCHMAKER™, CALL US AT 800-645-9292 AND WE'LL SEND YOU THE VIDEO FREE.
NO HASSLE GUARANTEE: IF FOR ANY REASON YOU ARE NOT COMPLETELY SATISFIED WITH THE MATCHMAKER™ SIMPLY RETURN IT TO US UNDAMAGED WITHIN 30 DAYS OF RECEIPT, FREIGHT PREPAID, FOR A PROMPT REFUND OF YOUR PURCHASE PRICE. YOU ALSO HAVE A ONE YEAR WARRANTY AGAINST DEFECTS IN MATERIALS AND WORKMANSHIP. THE DETAILS OF THIS WARRANTY ARE AVAILABLE ON REQUEST.
TO HELP COMPLETE YOUR PROJECTS, MAY WE SUGGEST MATCHMAKER™ ACCESSORIES:
AIR CLAMP WITH LATCHING FOOT SWITCH - 826-077. LARGE AND SMALL PIN AND CRESCENT JOINT TEMPLATES - 878-561. MICRO-HEIGHT ADJUSTER - 889-386. ADJUSTABLE 1/2" AND 3/4" BLIND DOVETAIL TEMPLATES - 900-216. CENTERING PIN SET - 889-379. SINGLE TENON TEMPLATES - 95-801. DOUBLE TENON TEMPLATES - 95-830. SHUTTER MORTISE TEMPLATE - 95-855. ROUND TENON TEMPLATES - 95-889. DOVETAIL TEMPLATES - 95-900. BOX JOINT TEMPLATES - 95-904.
|
|
|
|
Portable Power Tool Accessories - Drills
|
DOUBLE EDGE TO EDGE DOWEL JIG
|
| 1/4" Bushings For 100131 Doweling Jig
...plus other(s)
|
WITH OTHER EDGE-TO-EDGE DOWEL JIGS, YOU NEED TO DRILL HOLES INTO ONE BOARD, REMOVE THE JIG, ATTACH IT TO THE SECOND BOARD AND HOPE THE HOLES ALIGN. WITH THIS EXCLUSIVE DOUBLE EDGE-TO-EDGE DOWELING JIG (PATENT 5,051,042) YOU CAN DRILL FOUR PERFECTLY ALIGNED HOLES INTO BOTH BOARDS - AT THE SAME TIME:
PLACE ONE BOARD IN EACH SIDE OF THE JIG, ALIGN AND CLAMP THE ENDS, THEN PUSH THE CLAMP UP AGAINST THE BOARDS AND TIGHTEN THE SPIN NUT. NO EXTRA ADJUSTMENTS REQUIRED. AFTER DRILLING THE FIRST TWO HOLES IN EACH BOARD, LOOSEN THE SPIN NUT, SLIDE THE JIG DOWN TO WHERE YOU WANT THE NEXT DOWELS, TIGHTEN AND DRILL BOTH BOARDS, AGAIN. HANDLES WORKPIECES 1/4" TO 2-1/4" THICK. PRECISION-MACHINED, DIE-CAST ALUMINUM (NO PLASTIC) - BLACK OXIDE STEEL SHAFTS. INCLUDES ONE 1/4", 5/16", 3/8" AND 1/2" HARDENED STEEL, SELF-LOCKING DRILL GUIDE BUSHINGS, ALLEN WRENCH AND INSTRUCTIONS. APPROXIMATELY 8-5/8"L X 6"W X 3"H (WHEN FOLDED), WEIGHS 2 LBS. 9 OZ. ORDER EXTRA BUSHINGS (SOLD IN PACKAGES OF THREE) SO YOU CAN WORK EVEN FASTER. IMPORTED.
TO HELP COMPLETE YOUR PROJECT, MAY WE SUGGEST:
829-008 - ECONOMY 7-PIECE BRADPOINT BIT SET - CLICK HERE.
|
|
|
|
Advanced Search Tools
Browse
symbol next to the category that matches your desired product and select a sub-category link.
